|
Show your rotary car build up. Show off your Rotary Car build! |
![]() |
|
Thread Tools | Display Modes |
|
![]() |
#1 |
Don Mega
Join Date: Dec 2008
Location: Utopia
Posts: 1,688
Rep Power: 18 ![]() |
I have a fair bit of information to pass on (need to collated it first) but here is a quick rundown of today’s work.
Boost re-learn at 1.35kg/cm 3rd gear pull from 2500rpm = 1+ bar or ~15psi boost by 4300rpm 4th gear pull from same revs = 15+psi by 3600rpm VBOX3i results (on boost learning) max boost at this stage was like 1.25kg/cm or about 17.2psi 90-140kmh = 2.88 seconds, showed 272rwkw on Blitz power logging at 6800rpm and same power on my VBOX dyno plot (272rwkw @ 7000rpm) Repeated same test in exact same location as the small incline (so I could overlay graphs and see difference to flat piece of road and it ran 3.07 seconds (v’s the 3.25 yesterday) exact same vehicle weight (cross checked on corner scales this morning ).. AFR on these pulls was 11.1 to 11.0 across the range all smoothed out and boost was pretty similar to the first run where I did the comparison for you.. so trim of fuel mixture helped the time improvement. So after lunch I poured over the data and did some more trimming (2% reduction of fuel map) and went for a cruise. I gave it a few hits and it felt unreal in 2nd gear ![]() I’ll wait for a cool morning and take out the 20kg worth of spare tire, tools, fire extinguisher! And run it at ¼ tank of fuel and I should beat my 2.75 second 90-140 record. As a side note when I was at track and it was doing 90-140 in 3.05 second range, I did 100kmh to 200kmh in 8.1 to 8.2 seconds range at same weight (1350kg total). I’ll hope to do this in 7 seconds flat now as now I can hold 4th gear due to the much better top end power with no loss of 4700rpm to 7100rpm power range (as measured in the 90-140 tests in 3rd gear). It’s a win mate. ![]()
__________________
www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration |
![]() |
![]() |
![]() |
#2 |
Don Mega
Join Date: Dec 2008
Location: Utopia
Posts: 1,688
Rep Power: 18 ![]() |
Polished the bad boy today, fucken in love
![]() ![]() ![]()
__________________
www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration Last edited by RICE RACING; 11-14-2010 at 10:45 AM. Reason: more pics |
![]() |
![]() |
![]() |
#3 |
Don Mega
Join Date: Dec 2008
Location: Utopia
Posts: 1,688
Rep Power: 18 ![]() |
Well
![]() Fitted up the new waste gate springs yesterday bought option of 1.3 bar and 1.4 bar Tail springs (combination of different inner and outers). I settled on the lower 1.3bar combo just in case they gave a higher set boost. Along with the new higher power setting I upgraded the specification of the spark plugs and some other details too. Took the "beast" out for a drive today and the boost went to 1.53 to average of 1.50kg/cm! which is around 1.47 to 1.50bar! or old money 21+psi boost ![]() Fuel duty before was around 67% > now 75% same AFR Power on the Blitz was just under 300rwkw Peak fuel pressure was 70psi now its around 75psi EGT peaks have not gone above 890deg C First cool morning will go out and do a test of the 90-140kmh and also do a 100kmh to 200kmh acceleration test report along with VBOX power graph.
__________________
www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration |
![]() |
![]() |
![]() |
#4 |
Don Mega
Join Date: Dec 2008
Location: Utopia
Posts: 1,688
Rep Power: 18 ![]() |
![]() ![]() ![]() Did a 90-140km 3rd gear test but battery went flat before all data could be written *I know excuses lol* covered the speed increment in 85m, previous best was 88m, off ECU data logging and given this distance its around 2.62 seconds which is Ferrari F40 beating territory. Boost on 3rd gear pull from 2500rpm 130kpa (18.9psi) ~ 4400rpm 145kpa (21psi) ~ 5000rpm holding to 8000rpm Turbo speed is 110,000+rpm now lol EGT fr 928 deg C rr 930 deg C peak. AFR 11.3:1 After the boost controller learned the new spring the power delivery is so violent in 2nd gear even with warm semi slicks it just throws the car sideways down the road and leaves two black lines on the road ![]() ![]() From my best estimates its making around 490bhp to 500bhp at the engine corrected to std temp and pressure. Through a full catalyst equipped exhaust that is very quiet for road running *sounds nice at full power and revs* Engine has logged over 100 hours of use now at pretty high power settings, covered over 5000km testing. Hope to update with some nice VBOX graphs soon, though the weather here is shit at the moment, stupidly hot and monsoon conditions daily ![]()
__________________
www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration |
![]() |
![]() |
![]() |
#5 |
REIAN
Join Date: Feb 2008
Posts: 112
Rep Power: 18 ![]() |
Man your car is sick clean. Nice to see your putting the effort in getting your car tuned right. Can't wait to have my car put back together. Had it apart for painting....
__________________
1989 Turbo II. Track Car 1988 10thAE. Garage Queen 400+rwhp |
![]() |
![]() |
![]() |
#6 |
The Newbie
Join Date: Jan 2010
Location: alhambra, CA
Posts: 8
Rep Power: 0 ![]() |
That is a impressive set up man. I have to agree, thats a nice air box you got there
|
![]() |
![]() |
![]() |
Bookmarks |
|
|