prosport sender in factory location?

RotaryXperiment · 04-26-2011, 06:41 PM

can it will in the rear iron on a s5 iron? and how accurate is it there

My5ABaby · 04-26-2011, 07:02 PM

Quote:

Originally Posted by RotaryXperiment

can it will in the rear iron on a s5 iron? and how accurate is it there

RotaryXperiment · 04-26-2011, 07:06 PM

can it fit fit in rear iron (stock sender location)

RotaryXperiment · 04-26-2011, 07:11 PM

looks like factory is a 1/8 BPS and sender 1/8 NPT

infernosg · 04-26-2011, 07:23 PM

Yep, Mazda likes to use 1/8" BSPT for their oil pressure senders. It IS NOT the same as 1/8" NPT but adapters are easy to find (McMaster). As far as accuracy goes I'd assume it's accurate enough for whatever use you have in mind considering it is the location Mazda decided to put their unit.

RotaryXperiment · 04-26-2011, 07:29 PM

o btw i meant for coolant temp

sometimes i type and think my thoughts are coming out onto words on the keyboard lol

JustJeff · 04-26-2011, 11:54 PM

Yes coolant temp sender will thread in the S5 rear iron spot

RotaryXperiment · 04-27-2011, 06:14 AM

arent they different threads though?

Pete_89T2 · 04-27-2011, 07:51 AM

Quote:

Originally Posted by RotaryXperiment

arent they different threads though?

YES - the Prosport sender is 1/8"NPT, the hole Mazda threaded into the rear iron is 1/8"BSPT - you will STRIP the threads if you try screwing the Prosport sender directly in there. Buy the adapter.

RotaryXperiment · 04-27-2011, 09:56 AM

u can fit their sender o their 1/8 bsp adapter. sender is too long and that adapter might effect reading.
im using and adapter now on the back of wp housing right under ecu thermosensor and the reading can be as far as 20* off, comparing haltech temp reading to prosport gauge

JustJeff · 04-27-2011, 10:03 AM

We are talking about the rear iron water temp location correct? Unless I'm remembering incorrectly I have taken my Prosport temp sender and screwed it into the rear iron water temp location. It screws all the way down without ever catching. My engine is in pieces, next time I'm messing with parts I'll do it again to make sure.

RotaryXperiment · 04-27-2011, 10:32 AM

ya i was asking about factory temp sender location in rear iron.

JustJeff · 04-27-2011, 11:06 AM

^I may need to leave work early today. If that happens I'll check again, but from memory my Prosport threaded onto my S5 rear iron without ever catching or tearing up threads.

RotaryXperiment · 04-27-2011, 11:26 AM

ya if u can check for me that would be great!

RotaryXperiment · 04-27-2011, 04:00 PM

and how accurate was it there? my current spot on wp housing and adapter is 15-20* off

04-26-2011, 06:41 PM	#1
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	prosport sender in factory location? can it will in the rear iron on a s5 iron? and how accurate is it there

04-26-2011, 07:23 PM	#5
infernosg IT'S ALIVE! Join Date: Dec 2009 Location: Richmond, VA iTrader: (5) Posts: 811 Rep Power: 15	Yep, Mazda likes to use 1/8" BSPT for their oil pressure senders. It IS NOT the same as 1/8" NPT but adapters are easy to find (McMaster). As far as accuracy goes I'd assume it's accurate enough for whatever use you have in mind considering it is the location Mazda decided to put their unit. __________________ '86 Mazda RX-7 Base '79 Mazda RX-7 GS

04-26-2011, 07:06 PM	#3
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	can it fit fit in rear iron (stock sender location)

04-26-2011, 07:11 PM	#4
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	looks like factory is a 1/8 BPS and sender 1/8 NPT

04-26-2011, 07:29 PM	#6
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	o btw i meant for coolant temp sometimes i type and think my thoughts are coming out onto words on the keyboard lol

04-27-2011, 06:14 AM	#8
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	arent they different threads though?

04-27-2011, 09:56 AM	#10
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	u can fit their sender o their 1/8 bsp adapter. sender is too long and that adapter might effect reading. im using and adapter now on the back of wp housing right under ecu thermosensor and the reading can be as far as 20* off, comparing haltech temp reading to prosport gauge

04-27-2011, 10:32 AM	#12
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	ya i was asking about factory temp sender location in rear iron.

04-27-2011, 11:26 AM	#14
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	ya if u can check for me that would be great!

04-27-2011, 04:00 PM	#15
RotaryXperiment Rotary Fanatic Join Date: Mar 2008 Location: Bradenton, Fl iTrader: (0) Posts: 136 Rep Power: 17	and how accurate was it there? my current spot on wp housing and adapter is 15-20* off