FD3S RX-7 Engine Mounted Oil Catch Tank GB

RotaryWhat? · 01-22-2009, 09:25 PM

Regarding the premix tank design---I can't think of a filler/cap location better than what you pretty much have drawn up. Attached is a picture showing the routing of the IC piping (mine will be similar)----I think your tank will still fit. Perhaps you could cut off the top part of the tank on the drivers side just to make a little more clearance? I don't think it will affect the capacity much, and if you could run the sight line out of the front instead of top I think there would be enough room. What do you think?

Also, I wanted to make sure that your tank will have clearance for the steel braided oil metering lines around the water pump---it looks pretty close in some of your pictures.

afgmoto1978 · 01-23-2009, 01:01 PM

Quote:

Originally Posted by RotaryWhat?

Regarding the premix tank design---I can't think of a filler/cap location better than what you pretty much have drawn up.

Also, I wanted to make sure that your tank will have clearance for the steel braided oil metering lines around the water pump---it looks pretty close in some of your pictures.

I came to that conclusion last week, here's what your's is going to look like.

I did take that into account, it will be tight, but they will fit.

afgmoto1978 · 01-23-2009, 01:05 PM

I need a deposit of $50 via PayPal. PayPal Account: jw_griffith@msn.com

PM me you’re shipping address ahead of time so I can give you an accurate shipping quote.

I plan to have these catch tanks done by the end of January 2009. Once I’m finished making them I will contact you and request a final payment of $100 + shipping payment.

You will get the following:

1) 1.1 Liter catch tank, with a raw aluminum sand blasted finish.
2) One steel ball valve petcock for drainage
3) K&N air filter
4) Sight line fittings and clear line – preinstalled
5) 3/8” steel breather line mounted to the rear turbo oil drainage mounting point.
6) 3/8” Silicone hose
7) Brass push on fittings and hose clams
8) 2 6mm bolts & 2 6mm nuts

If you want the catch tank powder coated or polished it will be extra. PM me for price quote.

Interest List:

1. Trout2 - Depost Paid
2. RotaryWhat? - Deposit Paid
3. Astroboy - Paid in Full
4. John Magnuson - Deposit Paid
5. GoRacer
6. AHarada - Deposit Paid
7. hsitko - Deposit Paid

01-23-2009, 01:05 PM	#3
afgmoto1978 Rotary Fanatic Join Date: Mar 2008 Location: Portland, Oregon Posts: 381 Rep Power: 18	I need a deposit of $50 via PayPal. PayPal Account: jw_griffith@msn.com PM me you’re shipping address ahead of time so I can give you an accurate shipping quote. I plan to have these catch tanks done by the end of January 2009. Once I’m finished making them I will contact you and request a final payment of $100 + shipping payment. You will get the following: 1) 1.1 Liter catch tank, with a raw aluminum sand blasted finish. 2) One steel ball valve petcock for drainage 3) K&N air filter 4) Sight line fittings and clear line – preinstalled 5) 3/8” steel breather line mounted to the rear turbo oil drainage mounting point. 6) 3/8” Silicone hose 7) Brass push on fittings and hose clams 8) 2 6mm bolts & 2 6mm nuts If you want the catch tank powder coated or polished it will be extra. PM me for price quote. Interest List: 1. Trout2 - Depost Paid 2. RotaryWhat? - Deposit Paid 3. Astroboy - Paid in Full 4. John Magnuson - Deposit Paid 5. GoRacer 6. AHarada - Deposit Paid 7. hsitko - Deposit Paid Last edited by afgmoto1978; 01-30-2009 at 11:50 PM.