New project: 1976 Cosmo RX-5

[djmtsu]

I've got a few tricks to try on the rear caliper. Right now it is soaking in Evap-O-Rust. Tomorrow after work, I'll blow it out with compressed air and hope the 'clog' goes away. All the other brakes bled out fine. Only had 1 leak where the hardline meets the soft line for the rear axle.

Trans is also up and in. Talk about a PITA when you're by yourself, AND have to deal with a driveshaft that has a center bearing (READ- it stays put and the trans has to slide onto it),

I am really trying to get it together. I don't care if I have to screw on the headlight trim, tail lights, and bumpers the morning we're leaving. It is a little harder now to work on it, since I work until 6-7pm and Morgan goes to bed about 8:30. What's left isn't hard, there are just these little setbacks that get irritating!!!

Oh, and dropping $170 at Advance Auto today on JUST chemicals. Enough oil for 2 changes, gear oil, pre-mix, brake fluid, oil filters, acetone, carb cleaner. Ugh.

[FC Zach]

I feel ya bro, I had to replace that BA 3rd gen alternator you got me the hook up on and that muther F'er aint cheap! Even with an employee discount I paid $190. And I had to replace my starter for the second time since the previous replacement was just as bad as the other. . Starting to wonder what classifies these parts as "Remans", seriously. . do they just clean these parts and throw them back in a box? Hopefully the alternator is good on the first try since it is order only. . if not I'll have to convert back to 2nd gen or the 7 wont make it this year!

[TitaniumTT]

Originally Posted by djmtsu

So, my wheels are delayed....again....probably won't have them until another week and a half.

Because of this, I have a question:

Would you risk running the engine on jackstands? I am going to need to break it in, with only a short amount of time to do it!!!! It isn't a bridge or any huge port, so it should be fine.....right?

Are you talking about JUST the engine on jackstands or the engine in the car on the jackstands? The first... I wouldn't do it, not worth the time needed to set up all the aux systems to keep it running not to mention the fear of it falling off.

The second - There is no problem with that at all... in fact I always do it. Every engine that I build where I have the car, I start and run at a highish idle (1100rpms) on the jeckstands for at least an hour. Shut her down, check for leaks and let her cool over night. The next day stat idling... Anyone who knows me understands why I do what I do next - Break in lasts for 1000 miles. For the first 100 miles I don't exceed about 3-3500rpms after that I up the rev limit as follows.
100-200 miles - 4000 rpms
200-300 miles - 4500 rpms
300-400 miles - 5000 rpms
400-500 miles - 5500 rpms then change the oil
500-600 miles - 6000 rpms
600-700 miles - 6500 rpms
700-800 miles - 7000 rpms
800-900 miles - 7500 rpms
900-1000 miles all the way to 8k. After 1000 miles change the oil again and head to the dyno.
I stay out of boost as well... or try to... one or two lbs at mid rpms isn't going to hurt anything as long as it's already been tuned.

As far as how long it takes to break things in, it depends on what's been replaced and which Apex seals you used... the ones I like take a LONG time to break in. THe most recent engine I built kept gaining vacuum all the way into the 800 mile range. Granted a good deal of it is done in the first few hundred miles but I also over premix while they break-in and use a lot of oil/vasoline during assembly.

What's the deal with this engine? What all was replaced?

Originally Posted by djmtsu

Disassembling everything was easy. Putting it back together, not so much.

Right? That and I'm also fixing a laundry list of shit that has been bothering me for the last year.....

Originally Posted by djmtsu

It had all the wiring, but no actual CB radio. Tried to find a vintage one that fits the hole, but no luck. Power antenna for it is still there though!

Originally Posted by djmtsu

I have no doubt the engine is nothing other than perfect. Adler and Charles did a great job on this engine. It really is on me for performing the rest of the work to make it run. Hopefully I won't need to call for a 'All hands on deck' to make this thing ready to go. Everyone else around here are also on a time crunch to get their cars ready for DGRR.

Really?!?!?!? NO WAY??? :Smilielol5:

Originally Posted by djmtsu

I know alot of people are counting on this POS to show up at DGRR, and I really don't want to disappoint.

Nah.... we're gonna be disappointed if you don't show up.... bring the camry and we'll run on Hellbender.... see what the bitch can really do

Originally Posted by djmtsu

Some issues I'm dealing with now.

Can't install the engine on jack stands, the hoist can't get in the right position.

Reposition jackstands or use jack on front subframe until the hoist is in the right position then put the jackstands back

Originally Posted by djmtsu

Driver side rear caliper won't bleed. Like, no fluid will come out.

Could be hose, we talked about this

Originally Posted by djmtsu

Wheels STILL AREN'T FUCKING HERE.

Mine neither, he's HOPING for Friday... bastard is weeks late.... happy I am not....

Originally Posted by djmtsu

Need to pressure wash the tank. Weather has been shitty.

Did you wake up to snow this morning and leave your neighbor a fresh pile of yellow snow before calling it a nigh.....errrr... morning? Than STFU!

Originally Posted by djmtsu

Running out of time. Might need some on the double help.

That.....

Originally Posted by FerociousP

All ya gotta do is ask bro. Just be ready for everybody else scrambling on their own stuff and the last weekend before DGRR to be Easter.

All moot if wheels don't show anyway...

Easter..... ummmmmm... sneeze... cough... I'm not feeling very well... just send me some Deviled Eggs

Originally Posted by djmtsu

Oh, and dropping $170 at Advance Auto today on JUST chemicals. Enough oil for 2 changes, gear oil, pre-mix, brake fluid, oil filters, acetone, carb cleaner. Ugh.

Ugh.... I've got to do that as well..... 16 quarts of oil, 10 of which are synthetic, 3 filters, and about 2 gals of RedLine tranny fluid.... EFFFFFFFUUUUUUUUU