runs a couple of times

rotaryguy481 · 01-31-2010, 01:27 PM

i have a 87 seven N/A and i can get it to run a couple of times and when i turn it off it will not start for a couple of hours then when i try it it starts just fine for a couple of times then the prossess starts all over again can anyone give me an idea where to start

Whizbang · 01-31-2010, 01:33 PM

as in starts and runs until you turn it off next? Is it drivable will it runs? Does this only occur while the car is fully warmed up?

***TitaniumTT*** · 01-31-2010, 01:33 PM

You have leaky fuel injectors. Pull them out, get them serviced by someone reputable.

rotaryguy481 · 01-31-2010, 02:14 PM

it does it when its run for alil then it does it and yes it runs and drives a couple of times then does the no start thing

vex · 01-31-2010, 03:31 PM

Two major possibilities, one has already been said by Titanium TT (TTT); Leaky fuel injector. The other possibility would be low compression (especially if it's an NA). As such check compression to ensure proper compression

rotaryguy481 · 01-31-2010, 05:32 PM

well the compression is around 112 on front and back is that ok

***TitaniumTT*** · 01-31-2010, 06:32 PM

Yes, that's really good. It's your injectors. I would put money on it UNLESS when it's not starting it's becuase the prior time you drove it it wasn't fully warmed up. If it was taken to normal temp before shut down than it's your injectors leaking.

rotaryguy481 · 01-31-2010, 06:53 PM

how much could i get a good set for and which ones are the primary and which are the secondary

Whizbang · 01-31-2010, 07:21 PM

primary are tuck under the intake manifold with the ports actually on the engine, secondaries are found on top of the intake manifold and are considerably easer to access

***TitaniumTT*** · 01-31-2010, 08:55 PM

$400 for a new set or ~$100 to get them serviced.......................................... ........................................

rotaryguy481 · 01-31-2010, 10:11 PM

aight thanx guys now i just got to find a place around me to service them lol

01-31-2010, 01:27 PM	#1
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	runs a couple of times i have a 87 seven N/A and i can get it to run a couple of times and when i turn it off it will not start for a couple of hours then when i try it it starts just fine for a couple of times then the prossess starts all over again can anyone give me an idea where to start

01-31-2010, 01:33 PM	#2
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	as in starts and runs until you turn it off next? Is it drivable will it runs? Does this only occur while the car is fully warmed up? __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

01-31-2010, 01:33 PM	#3
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	You have leaky fuel injectors. Pull them out, get them serviced by someone reputable. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

01-31-2010, 03:31 PM	#5
vex RCC Loves Me Not You Join Date: Jul 2008 Location: Influx. iTrader: (6) Posts: 2,113 Rep Power: 19	Two major possibilities, one has already been said by Titanium TT (TTT); Leaky fuel injector. The other possibility would be low compression (especially if it's an NA). As such check compression to ensure proper compression __________________ The Official FC Radiator Thread My Project Thread: Cerberus CCVT Virginia Rotary Group

01-31-2010, 06:32 PM	#7
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Yes, that's really good. It's your injectors. I would put money on it UNLESS when it's not starting it's becuase the prior time you drove it it wasn't fully warmed up. If it was taken to normal temp before shut down than it's your injectors leaking. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

01-31-2010, 02:14 PM	#4
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	it does it when its run for alil then it does it and yes it runs and drives a couple of times then does the no start thing

01-31-2010, 05:32 PM	#6
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	well the compression is around 112 on front and back is that ok

01-31-2010, 06:53 PM	#8
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	how much could i get a good set for and which ones are the primary and which are the secondary

01-31-2010, 07:21 PM	#9
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	primary are tuck under the intake manifold with the ports actually on the engine, secondaries are found on top of the intake manifold and are considerably easer to access __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

01-31-2010, 08:55 PM	#10
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	$400 for a new set or ~$100 to get them serviced.......................................... ........................................ __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

01-31-2010, 10:11 PM	#11
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	aight thanx guys now i just got to find a place around me to service them lol