TII trans

FCTII · 09-29-2009, 06:36 PM

will a TII trans work with an N/A motor?

Whizbang · 09-29-2009, 06:43 PM

yes but you need the proper turbo flywheel and clutch compoenets. Also you need to find a solution to the fact the transmission is longer so the na driveshaft wont work and the Turbo shaft wont either.

***TitaniumTT*** · 09-29-2009, 06:58 PM

I don't think the trans is longer, it's more of an issue of the splines are difference between the N/A and TII trans and the flange on the diff is different as well. So there is no stock driveshaft that will work. Mazdatrix has a few driveshafts that they offer that will solve the problems.

What you need to make the trans work with the engine is the proper counterweight and flywheel. S4 and S5 counterweights are different weights and the n/a vs TII flywheels are of different diameter. So you need to match the couterweight to the series engine and the flywheel to the trans.

You'll also need the proper sized clutch disc and PP. Obviously these are specific to the flywheel.

You'll also need the correct starter. Again, specific to the trans.

Whizbang · 09-29-2009, 07:19 PM

the transmission is actually longer as well. Another option is using a T5 adapter. See the trans and diff faq.

***TitaniumTT*** · 09-29-2009, 07:50 PM

Or once I acheive full apocalyptic evil genius status I can build you a 6 spd that will bolt right in.

I've got both a TII and N/A driveshaft kicking around, I think I'm gonna have to measure them. I think it's like a 3/8" difference. The trans is not longer in the sense that it won't fit though or the shifter won't line up.

Whizbang · 09-29-2009, 08:02 PM

if i recall it was more in the tail housing section

djmtsu · 09-29-2009, 08:51 PM

Here is what you need to do it:

TII trans
TII clutch slave cylinder
TII flywheel
TII starter

And from what I have seen (and done) a vert driveshaft might work for you.

RotaryProphet · 09-30-2009, 01:35 AM

Instead of swapping flywheels & clutches, you could order a clutch disk for less than $100 with the T2 spline pattern and the NA diameter. There are quite a few places that could build this for you, or Mazdatrix sells a 6 puck with this setup.

***TitaniumTT*** · 09-30-2009, 06:54 AM

If he has an N/A flywheel and wants to use a TII trans, the starters won't line up with the flywheels. He'll need a TII flywheel to use with the TII trans. The N/A PP that he currently has will not fit on the TII flywheel that he'll need to get to use with the TII flywheel if he's using the TII trans. N/A clutchs are 225mm diameter and the Turbos are either 240 or 235.

So, to the best of my knowledge an N/A PP will NOT fit on a TII flywheel. So, to add to DJ's list, you'll need to add a disc and PP.

NoDOHC · 09-30-2009, 06:04 PM

Out of curiousity, what is your reason for wanting to upgrade? If you want an NA transmission, go to eBay and buy one for around $75.00 any day you want one.

The turbo transmission will require a custom driveshaft to connect to the NA diff (different splines). Plus it will require a lot of electrical work (the wires for the reverse lights, 5th gear switch and neutral switch will not reach). The NA trans will take NA power just fine (if it starts out in good shape).

I have killed two of them, but both were old to start with and I am making 160 Wlb-ft of torque (200 Lb-ft at the flywheel).

Whizbang · 09-30-2009, 06:32 PM

vert driveshafts are just the same. An automatic driveshaft may work though

Flooder · 09-30-2009, 11:21 PM

The auto drive shaft will work.

SecondGenPat · 10-04-2009, 05:25 PM

Quote:

Originally Posted by Flooder

The auto drive shaft will work.

you are saying that the drive shaft from an automatic will allow you to use a T2 trans with and N/A engine (as long as the clutch/ flywheel is correct)??

I ask because I have both the T2 trans and an auto drive shaft in the garage.

Thanks
-Pat

FCTII · 10-05-2009, 06:17 PM

Quote:

Originally Posted by NoDOHC

Out of curiousity, what is your reason for wanting to upgrade? If you want an NA transmission, go to eBay and buy one for around $75.00 any day you want one.

The turbo transmission will require a custom driveshaft to connect to the NA diff (different splines). Plus it will require a lot of electrical work (the wires for the reverse lights, 5th gear switch and neutral switch will not reach). The NA trans will take NA power just fine (if it starts out in good shape).

I have killed two of them, but both were old to start with and I am making 160 Wlb-ft of torque (200 Lb-ft at the flywheel).

My buddy's just went out and i have a spare tii trans and i was just gunna let him buy it off of me. but since it would be easier and chaeper for him to just buy an n/a one he'll just do that.

Black91n/a · 10-06-2009, 11:52 PM

Quote:

Originally Posted by NoDOHC

The turbo transmission will require a custom driveshaft to connect to the NA diff (different splines). Plus it will require a lot of electrical work (the wires for the reverse lights, 5th gear switch and neutral switch will not reach). The NA trans will take NA power just fine (if it starts out in good shape).

You can get such a driveshaft from Mazdatrix and all I had to do for wiring was to extend 4 wires and change a connector, not really what I'd call "a lot of electrical work".

Quote:

Originally Posted by Flooder

The auto drive shaft will work.

Yes it has the right connections for the TII trans and NA diff, but it's really too short to be a decent solution. You can probably find a driveshaft shop in your area that can extend it for you though to make it a proper solution.

09-29-2009, 06:36 PM	#1
FCTII Rotary Fan in Training Join Date: Mar 2009 iTrader: (-1) Posts: 42 Rep Power: 0	TII trans will a TII trans work with an N/A motor?

09-29-2009, 06:43 PM	#2
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	yes but you need the proper turbo flywheel and clutch compoenets. Also you need to find a solution to the fact the transmission is longer so the na driveshaft wont work and the Turbo shaft wont either. __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

09-29-2009, 06:58 PM	#3
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I don't think the trans is longer, it's more of an issue of the splines are difference between the N/A and TII trans and the flange on the diff is different as well. So there is no stock driveshaft that will work. Mazdatrix has a few driveshafts that they offer that will solve the problems. What you need to make the trans work with the engine is the proper counterweight and flywheel. S4 and S5 counterweights are different weights and the n/a vs TII flywheels are of different diameter. So you need to match the couterweight to the series engine and the flywheel to the trans. You'll also need the proper sized clutch disc and PP. Obviously these are specific to the flywheel. You'll also need the correct starter. Again, specific to the trans. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

09-29-2009, 07:19 PM	#4
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	the transmission is actually longer as well. Another option is using a T5 adapter. See the trans and diff faq. __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

09-29-2009, 07:50 PM	#5
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Or once I acheive full apocalyptic evil genius status I can build you a 6 spd that will bolt right in. I've got both a TII and N/A driveshaft kicking around, I think I'm gonna have to measure them. I think it's like a 3/8" difference. The trans is not longer in the sense that it won't fit though or the shifter won't line up. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

09-29-2009, 08:02 PM	#6
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	if i recall it was more in the tail housing section __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

09-29-2009, 08:51 PM	#7
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Here is what you need to do it: TII trans TII clutch slave cylinder TII flywheel TII starter And from what I have seen (and done) a vert driveshaft might work for you. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

09-30-2009, 01:35 AM	#8
RotaryProphet Rotary Fanatic Join Date: Sep 2008 iTrader: (0) Posts: 147 Rep Power: 17	Instead of swapping flywheels & clutches, you could order a clutch disk for less than $100 with the T2 spline pattern and the NA diameter. There are quite a few places that could build this for you, or Mazdatrix sells a 6 puck with this setup.

09-30-2009, 06:54 AM	#9
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	If he has an N/A flywheel and wants to use a TII trans, the starters won't line up with the flywheels. He'll need a TII flywheel to use with the TII trans. The N/A PP that he currently has will not fit on the TII flywheel that he'll need to get to use with the TII flywheel if he's using the TII trans. N/A clutchs are 225mm diameter and the Turbos are either 240 or 235. So, to the best of my knowledge an N/A PP will NOT fit on a TII flywheel. So, to add to DJ's list, you'll need to add a disc and PP. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

09-30-2009, 06:04 PM	#10
NoDOHC The quest for more torque Join Date: Sep 2008 Location: Sheboygan, Wisconsin iTrader: (1) Posts: 855 Rep Power: 17	Out of curiousity, what is your reason for wanting to upgrade? If you want an NA transmission, go to eBay and buy one for around $75.00 any day you want one. The turbo transmission will require a custom driveshaft to connect to the NA diff (different splines). Plus it will require a lot of electrical work (the wires for the reverse lights, 5th gear switch and neutral switch will not reach). The NA trans will take NA power just fine (if it starts out in good shape). I have killed two of them, but both were old to start with and I am making 160 Wlb-ft of torque (200 Lb-ft at the flywheel). __________________ 1986 GXL ('87 4-port NA - Haltech E8, LS2 Coils. Defined Autoworks Headers, Dual 2.5" Exhaust (Dual Superflow, dBX mufflers) 1991 Coupe (KYB AGX Shocks, Eibach lowering springs, RB exhaust, Stock and Automatic)

09-30-2009, 06:32 PM	#11
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	vert driveshafts are just the same. An automatic driveshaft may work though __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

09-30-2009, 11:21 PM	#12
Flooder Rotary Fanatic Join Date: Feb 2008 Location: Tucson, Arizona iTrader: (0) Posts: 321 Rep Power: 17	The auto drive shaft will work. __________________ AZRX7.COM Red 1991 A-package(SOLD) Red 1990 GXL(SOLD) White 1989 GTUs(DEAD) Red 1988 Turbo II(DD) Black 1988 Turbo II(SOLD) Rebuilt and street ported motor, Garrett T04E Turbo, 3" Turbo Inlet Duct/AEM Dry Flow Filter, Your Mom's MBC, Blitz FMIC, 890cc and 1000cc injectors, Tomei FPR, Walbro, Rtek 2.1 ECU, Taurus E-Fan, Turbonetics BOV, 3" Motoria/Corksport Turbo Back Exhaust, Emissions Removed, Greddy Boost Gauge, Megan Racing Water Temp Gauge, 5one5 Triple Gauge Pod, AEM Uego, GP Sports Body Kit, Fiber Images CF Hood, S5 Seats, S5 Tails, S5 Alt, Dual Alt Pulley, D2 Coilovers, NRG Quick Release, Shook Motorsports Radiator, HID's, AN/Steel Braided Oil Cooler Lines, SUPER JDM TYTE DRIFT BUTTON www.DensetsuMotorsports.com www.AZRX7.Com www.FloodersAdventure.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode