Crimping vs. Soldering

Mutaku · 04-23-2013, 10:08 PM

Quote:

Originally Posted by TitaniumTT

Use the ECU that I learned on and come back and talk to me

I agree, which is why I only crimp

I usually just say I crimp on aircraft so you should just crimp your car. If I go any deeper people get all retarded lol

***TitaniumTT*** · 04-24-2013, 04:14 PM

Got a car on the dyno that just dropped a tach signal

ZOMGWTFBBAYGTBKMNFW!!!!!! A BROKEN SOLDER JOINT!!!!!

Gonna go crimp that shit together

Rotary Evolution · 04-24-2013, 04:40 PM

i had one a few days ago, bad crimp junction.

i replaced the 25 year old connector and crimps(with shortened solid wires to the new connector), but that's just me. and don't be one of those donks who hard wires the CAS to the ECU...(seen it done plenty on FCs, along with ignition wiring)

if you think it bothers me that you found a bad solder joint, good luck with that. i've seen every sort of wire repair fail(improperly done). yet i haven't had any cars come back.

RICE RACING · 04-24-2013, 05:18 PM

Fuck! tuned a car last night and its ECU case was in what look like a gold colored Aluminum window frame extrusion and the end were held on with roofing screws!!!!

WTF!

RICE RACING · 04-24-2013, 05:21 PM

Quote:

Originally Posted by Rotary Evolution

i've seen every sort of wire repair fail(improperly done). yet i haven't had any cars come back.

Now imagine if you were Howard Coleman or Brian D Cain, you would have no cars come back or leave for that matter!

Hard to have any wiring failures when the motors fail just after the starter motor engages the flywheel ring gear LOL.

Rotary Evolution · 04-24-2013, 06:01 PM

well i did just have one leave today that was here for a year and a half.. i felt like taking a sledge hammer to that car many times, especially when i found the ground strap from the battery loose, burned and bolted to a painted chassis surface.

don't ask, that car was a wiring nightmare and i should have told him to pick it up long ago. shitty part is it ran fine until under full load, then shit would start crapping out erratically. sometimes you feel like it's your own damn fault for not checking the idiocy factor of others.

04-24-2013, 04:14 PM	#107
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Got a car on the dyno that just dropped a tach signal ZOMGWTFBBAYGTBKMNFW!!!!!! A BROKEN SOLDER JOINT!!!!! Gonna go crimp that shit together __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

04-24-2013, 04:40 PM	#108
Rotary Evolution rotaryevolution.net Join Date: Feb 2011 Location: Las Vegas, NV iTrader: (0) Posts: 248 Rep Power: 14	i had one a few days ago, bad crimp junction. i replaced the 25 year old connector and crimps(with shortened solid wires to the new connector), but that's just me. and don't be one of those donks who hard wires the CAS to the ECU...(seen it done plenty on FCs, along with ignition wiring) if you think it bothers me that you found a bad solder joint, good luck with that. i've seen every sort of wire repair fail(improperly done). yet i haven't had any cars come back. __________________ http://rotaryevolution.net Last edited by Rotary Evolution; 04-24-2013 at 04:48 PM..

04-24-2013, 05:18 PM	#109
RICE RACING Don Mega Join Date: Dec 2008 Location: Utopia iTrader: (0) Posts: 1,688 Rep Power: 17	Fuck! tuned a car last night and its ECU case was in what look like a gold colored Aluminum window frame extrusion and the end were held on with roofing screws!!!! WTF! __________________ www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration

04-24-2013, 06:01 PM	#111
Rotary Evolution rotaryevolution.net Join Date: Feb 2011 Location: Las Vegas, NV iTrader: (0) Posts: 248 Rep Power: 14	well i did just have one leave today that was here for a year and a half.. i felt like taking a sledge hammer to that car many times, especially when i found the ground strap from the battery loose, burned and bolted to a painted chassis surface. don't ask, that car was a wiring nightmare and i should have told him to pick it up long ago. shitty part is it ran fine until under full load, then shit would start crapping out erratically. sometimes you feel like it's your own damn fault for not checking the idiocy factor of others. __________________ http://rotaryevolution.net

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode