FS: FD Engines - Stock, Streetported, & Bridgeported

r0t0rhead · 09-02-2011, 01:22 PM

1) Stock "FD" RX7 13B-REW Engine- $3000.00 plus shipping

2) Streetported "FD" RX7 13B-REW Engine= $4000.00 with Racung Beat aluminum flywheel, (as pictured)
or $3500.00 with stock flywheel

3) Bridgeported "FD" RX7 13B-REW- $4800.00 Secondary ports only have large Bridgeporting, primary ports are Streetported, Rotor Housings are match ported for the secondary ports intake bridgeporting and exhaust ports are also ported. Includes stock flywheel- Good used Racing Beat aluminum flywheel also available with this engine for additional cost $400.00

These engines were built to our our competition proven specifications and include all new seals, springs, 0-rings, bearings & gaskets, also include upgraded apex seals, combustion & water seals

Stock Engines are warranted for 1-yr.
*Engine Core return required on each engine- $900.00 core charge if no core returned
*Warranty does not cover damage caused by turbo overboost or lean operation under boost.

For more information- http://rotorsportsracing.com/perform...ng/engines.htm
(please note- our website has not been updated in 6 yrs, so pricing listed on site is inaccurate)

Please contact us with any questions,

Bryan Smith
Rotorsports Racing
465 Russell Farm Rd.
Kannapolis, NC 28081
(704) 933-6222

email- info@rotorsportsracing.com

r0t0rhead · 10-20-2011, 08:04 PM

sale pending on stock ported engine

yzf-r1 · 10-30-2011, 10:34 PM

Nice looking motors...

imstillonjava · 10-30-2011, 11:49 PM

Hi Bryan,
are these motors equivalent to your sites' "Stage 1" build?

r0t0rhead · 11-02-2011, 11:45 PM

To answer your question....Yes & No

Our website hasn't been updated since '05 (but soon to be revamped), so both specs and pricing have changed. They are prepped to our latest Stage 1 specs but with improvements that are not listed on website.

All Stage 1 engines now receive new upgraded and cryogenic treated apex seals and springs in addition to all the other new seals, springs, bearings, 0-rings, oil seals gaskets, assembly also includes a new Mazdaspeed metal front cover gasket (we've never had one of these fail or leak!)

E-shaft is checked for "run-out" then polished and thermal pellet installed, Side Housings are checked for wear and micro-lapped and ultra-sonic cleaned. Oil pressure regulator is pressure verified & oil pump is also clearanced & wear checked and tested.

**The "Stock" ported Engine and the "Streetported" Engine have both been sold as of 11/01/'11

09-02-2011, 01:22 PM	#1
r0t0rhead Rotary Fanatic Join Date: Jun 2008 Posts: 192 Rep Power: 17	FS: FD Engines - Stock, Streetported, & Bridgeported 1) Stock "FD" RX7 13B-REW Engine- $3000.00 plus shipping 2) Streetported "FD" RX7 13B-REW Engine= $4000.00 with Racung Beat aluminum flywheel, (as pictured) or $3500.00 with stock flywheel 3) Bridgeported "FD" RX7 13B-REW- $4800.00 Secondary ports only have large Bridgeporting, primary ports are Streetported, Rotor Housings are match ported for the secondary ports intake bridgeporting and exhaust ports are also ported. Includes stock flywheel- Good used Racing Beat aluminum flywheel also available with this engine for additional cost $400.00 These engines were built to our our competition proven specifications and include all new seals, springs, 0-rings, bearings & gaskets, also include upgraded apex seals, combustion & water seals Stock Engines are warranted for 1-yr. Engine Core return required on each engine- $900.00 core charge if no core returned Warranty does not cover damage caused by turbo overboost or lean operation under boost. For more information- http://rotorsportsracing.com/perform...ng/engines.htm (please note- our website has not been updated in 6 yrs, so pricing listed on site is inaccurate) Please contact us with any questions, Bryan Smith Rotorsports Racing 465 Russell Farm Rd. Kannapolis, NC 28081 (704) 933-6222 email- info@rotorsportsracing.com

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-20-2011, 08:04 PM	#2
r0t0rhead Rotary Fanatic Join Date: Jun 2008 Posts: 192 Rep Power: 17	sale pending on stock ported engine

10-30-2011, 10:34 PM	#3
yzf-r1 Banned Join Date: Mar 2010 Posts: 67 Rep Power: 0	Nice looking motors...

10-30-2011, 11:49 PM	#4
imstillonjava Rotary Fanatic Join Date: Mar 2008 Posts: 108 Rep Power: 18	Hi Bryan, are these motors equivalent to your sites' "Stage 1" build?

11-02-2011, 11:45 PM	#5
r0t0rhead Rotary Fanatic Join Date: Jun 2008 Posts: 192 Rep Power: 17	To answer your question....Yes & No Our website hasn't been updated since '05 (but soon to be revamped), so both specs and pricing have changed. They are prepped to our latest Stage 1 specs but with improvements that are not listed on website. All Stage 1 engines now receive new upgraded and cryogenic treated apex seals and springs in addition to all the other new seals, springs, bearings, 0-rings, oil seals gaskets, assembly also includes a new Mazdaspeed metal front cover gasket (we've never had one of these fail or leak!) E-shaft is checked for "run-out" then polished and thermal pellet installed, Side Housings are checked for wear and micro-lapped and ultra-sonic cleaned. Oil pressure regulator is pressure verified & oil pump is also clearanced & wear checked and tested. **The "Stock" ported Engine and the "Streetported" Engine have both been sold as of 11/01/'11