S5 USDM NA to Jspec TII Vacuum Reroute

LunchboxCritter · 03-30-2010, 12:19 PM

Will this set up work for me? I am putting a J-spec TII S5 into my S5 NA car. I have removed the ACV, Split Air, Air Pump (installed dual pulleys on the alt), and have installed block off plates, I am planning on keeping the BAC as I'm keeping A/C. I am unsure how the oil catch should be hooked up, could someone confirm setup? Also can the stock pressure sensor be blocked off or does it need to be routed to the manifold?

FerociousP · 03-30-2010, 01:23 PM

If you are running the stock ECU then you need the pressure sensor hooked up. preferably the closest location to stock on the manifold. and don't forget there is a small pellet in that line...

LunchboxCritter · 03-30-2010, 01:44 PM

Quote:

Originally Posted by FerociousP

If you are running the stock ECU then you need the pressure sensor hooked up. preferably the closest location to stock on the manifold. and don't forget there is a small pellet in that line...

Okay thanks for the clarification (I am running OEM ECU). Here is a new diagram reflecting that. Is there anything else I'm missing or that I should know about this mod?

LunchboxCritter · 03-30-2010, 09:44 PM

Here is what I have so far. I ordered a Jaz oil catch and it should be here tomorrow. Please if you see something wrong let me know.

================================================== ============================================

This is scary looking to me. I could be retarded but shouldn't the wastegate be hooked to a controller?

================================================== ============================================

================================================== ============================================

Some of what all that I removed. I also removed the two hard lines from the oil line that crosses the top front of the short block to the turbo. P.S. the starter is not part of the mod; it is a spare.

LunchboxCritter · 03-30-2010, 11:42 PM

Disclaimer: I am in no way a mechanic, and I did not sleep at a Holiday Inn. I do not even know if I am doing this mod right. Please don't run out and copy what I am doing. I could not find any good pictures of this job; however I did find a pretty good write up about the process. I am sorry, if I am doing something wrong, and I would appreciate suggestions.

DO NOT TRY THIS AT HOME!!!

LunchboxCritter · 03-31-2010, 04:40 PM

Just a few more pics.

================================================== ================

Front of the TIM

================================================== ================

Back of the TIM (firewall side)

Gregory Casimir · 04-01-2010, 10:30 AM

so the oil catch can is hooked up in the right direction?

LunchboxCritter · 04-01-2010, 10:48 AM

Quote:

Originally Posted by Gregory Casimir

so the oil catch can is hooked up in the right direction?

I'm unsure of exactly how it should be hooked up, the diagram I colored was in hopes of some clarification. If someone knows for sure, please chime in here.

LunchboxCritter · 04-05-2010, 10:40 AM

Currently I have my setup like this, it fired right up and seems to run just fine. I am still short an exhaust and having only a downpipe installed I have yet to run it down the road.

================================================== ================

I will adding a boost controller and boost gauge in the next few days and then my setup will be like this. I will inform everyone how well it works as soon as I know for sure.

12arotary · 04-05-2010, 11:27 AM

you capped off your waste gate, you need your waste gate solenoid to pull open off vacuum

LunchboxCritter · 04-05-2010, 11:33 AM

Quote:

Originally Posted by 12arotary

you capped off your waste gate, you need your waste gate solenoid to pull open off vacuum

You are absolutely correct.

LunchboxCritter · 04-05-2010, 11:34 AM

Quote:

Originally Posted by 12arotary

you capped off your waste gate, you need your waste gate solenoid to pull open off vacuum

Thanks for pointing that out. I changed that before I started the car, I ran the turbo out and wastegate to a T fitting and then piped it to one of the vac on the front side of the top intake manifold. I have a manual boost controller that I'm going to put between the out on the turbo and the wastegate, and then I'll eliminate the hose running to the TIM. I'll get some updated pictures on here soon.

FerociousP · 04-05-2010, 12:58 PM

why would you run a hose to the intake manifold? How bout just leave it like stock until the boost controller?

djmtsu · 04-05-2010, 02:03 PM

Looky:

Connect those together.

There is supposed to be a metal 'ring' around the compressor coldside that has an output nipple. That nipple goes to the wastegate solenoid. If you are dumping the rats nest/emissions than you DON'T need it. Just connect the two together (compressor-to-wastegate).

Mine had the metal ring still, but I just capped it.

LunchboxCritter · 04-13-2010, 05:15 PM

Got a problem. Car won't boost, when it reaches half throttle and zero vacuum it stalls. Any ideas or suggestions?

Here is my current setup - Running an N374 ecu chipped with a speedlabs chip, n370 pressure sensor, correct maf sensor.

03-30-2010, 12:19 PM	#1
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	J-Spec TII Vacuum Reroute Will this set up work for me? I am putting a J-spec TII S5 into my S5 NA car. I have removed the ACV, Split Air, Air Pump (installed dual pulleys on the alt), and have installed block off plates, I am planning on keeping the BAC as I'm keeping A/C. I am unsure how the oil catch should be hooked up, could someone confirm setup? Also can the stock pressure sensor be blocked off or does it need to be routed to the manifold? Last edited by LunchboxCritter; 03-31-2010 at 05:03 PM..

03-30-2010, 01:23 PM	#2
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	If you are running the stock ECU then you need the pressure sensor hooked up. preferably the closest location to stock on the manifold. and don't forget there is a small pellet in that line... __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

03-30-2010, 09:44 PM	#4
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	Here is what I have so far. I ordered a Jaz oil catch and it should be here tomorrow. Please if you see something wrong let me know. ================================================== ============================================ This is scary looking to me. I could be retarded but shouldn't the wastegate be hooked to a controller? ================================================== ============================================ ================================================== ============================================ Some of what all that I removed. I also removed the two hard lines from the oil line that crosses the top front of the short block to the turbo. P.S. the starter is not part of the mod; it is a spare. Last edited by LunchboxCritter; 03-31-2010 at 12:01 AM.. Reason: added a picture

03-30-2010, 11:42 PM	#5
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	Disclaimer: I am in no way a mechanic, and I did not sleep at a Holiday Inn. I do not even know if I am doing this mod right. Please don't run out and copy what I am doing. I could not find any good pictures of this job; however I did find a pretty good write up about the process. I am sorry, if I am doing something wrong, and I would appreciate suggestions. DO NOT TRY THIS AT HOME!!! Last edited by LunchboxCritter; 03-30-2010 at 11:53 PM..

04-05-2010, 11:27 AM	#10
12arotary tumor-syphilis-itis-osis Join Date: Sep 2008 iTrader: (0) Posts: 191 Rep Power: 17	you capped off your waste gate, you need your waste gate solenoid to pull open off vacuum __________________ 82 300d 82 Gsl 84 b2200 Diesel 88 gxl

03-31-2010, 04:40 PM	#6
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	Just a few more pics. ================================================== ================ Front of the TIM ================================================== ================ Back of the TIM (firewall side)

04-01-2010, 10:30 AM	#7
Gregory Casimir Rotary Fanatic Join Date: Jan 2010 iTrader: (0) Posts: 253 Rep Power: 15	so the oil catch can is hooked up in the right direction?

04-05-2010, 10:40 AM	#9
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	Currently I have my setup like this, it fired right up and seems to run just fine. I am still short an exhaust and having only a downpipe installed I have yet to run it down the road. ================================================== ================ I will adding a boost controller and boost gauge in the next few days and then my setup will be like this. I will inform everyone how well it works as soon as I know for sure.

04-05-2010, 12:58 PM	#13
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	why would you run a hose to the intake manifold? How bout just leave it like stock until the boost controller? __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

04-05-2010, 02:03 PM	#14
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Looky: Connect those together. There is supposed to be a metal 'ring' around the compressor coldside that has an output nipple. That nipple goes to the wastegate solenoid. If you are dumping the rats nest/emissions than you DON'T need it. Just connect the two together (compressor-to-wastegate). Mine had the metal ring still, but I just capped it. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5 Last edited by djmtsu; 04-05-2010 at 02:05 PM..

04-13-2010, 05:15 PM	#15
LunchboxCritter Simply Rotarded Join Date: Jan 2009 Location: Florida iTrader: (0) Posts: 166 Rep Power: 16	Got a problem. Car won't boost, when it reaches half throttle and zero vacuum it stalls. Any ideas or suggestions? Here is my current setup - Running an N374 ecu chipped with a speedlabs chip, n370 pressure sensor, correct maf sensor. __________________ LunchboxCritter - 91 NA to J-Spec TII - 88 FC Vert - 04 Rx8 Disclaimer: I am not a mechanic, and I did not sleep at a Holiday Inn. DO NOT TRY THIS AT HOME!!! Last edited by LunchboxCritter; 04-14-2010 at 10:55 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode