Zero clearance side seals round 2. (If you don't mind Barry)

		Rotary Car Club > Tech Discussion > Rotary Tech - General Rotary Engine related tech section..
Zero clearance side seals round 2. (If you don't mind Barry)

Rotary Tech - General Rotary Engine related tech section.. Tech section for general Rotary Engine... This includes, building 12As, 13Bs, 20Bs, Renesis, etc...

Welcome to Rotary Car Club.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

If you have any problems with the registration process or your account login, please contact contact us.

Thread Tools

Display Modes

\r\n

\r\n\r\n

\r\n \r\n\r\n\r\n\r\n\r\n\r\n \r\n \r\n \r\n \r\n\r\n\r\n \r\n\r\n\r\n \r\n \r\n \r\n\r\n

\r\n \r\n \r\n 08-29-2015, 07:17 AM\r\n \r\n \r\n	\r\n \r\n #2\r\n \r\n
\r\n\r\n \r\n \r\n 88turboii\r\n \r\n \r\n\r\n \r\n\r\n \r\n \r\n\r\n \r\n \r\n \r\n __________________ \r\n -The Angry Stig- \r\nDGRR 2009, 2011, 2012 & 2013 - Best FC \r\n \r\nDEALS GAP!! WOOHOOOO!!!!! \r\n \r\n2015 Audi S4 - Samantha - Zero Brap S4 \r\n2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter \r\n2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO\'s! So it begins \r\n1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG\'s - Rotary Tow Vehicle \r\n1988 \'Vert - In progress \r\n1988 FC Coupe - Gretchen -The attention whore BEAST! \r\n \r\n \r\nI\'m a sick individual, what\'s wrong with you? \r\nI\'m pure Evil \r\nI\'m still insane, in the best possible way. \r\nI think Brian\'s idea of romance is using lube. \r\nYour rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. \r\nYou win with your thread. Most everything \r\nIt\'s a truck with a steel gate on the back. Just a statement of fact \r\n \r\nMotec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... \r\nNo Bolt-ons allowed. Dyno\'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. \r\n-Angry Motherf*cker Mode ENGAGED-\r\n \r\n \r\n \r\n\r\n \r\n\r\n \r\n\r\n
\r\n \r\n\r\n\r\n \r\n \r\n \r\n \r\n \r\n	\r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n

\r\n\r\n\r\n\r\n\r\n\r\n\r\n\r\n

\r\n \r\n

\r\n

\r\n\r\n

\r\n \r\n\r\n\r\n\r\n\r\n\r\n \r\n \r\n \r\n \r\n\r\n\r\n

\r\n \r\n

\r\n 03-14-2016, 04:00 PM\r\n \r\n \r\n

\r\n \r\n #17\r\n \r\n

\r\n\r\n

\r\n \r\n Barry Bordes\r\n

08-28-2015, 11:48 PM	#1
Slides Rotary Fan in Training Join Date: Apr 2012 Location: NSW, Australia iTrader: (0) Posts: 39 Rep Power: 0	Zero clearance side seals round 2. (If you don't mind Barry) I genuinely though Ted forgot the italics in his comment here until I saw it was actually closed. Not sure why you wouldn't want documentation of long term runner that someone has tested in one place? (I will say mods/admin on other forums encourage keeping tech stuff in one place) So, seems this is a goer. I would like to do this when I eventually get around to building one or other of my engines, the 12a will have to come apart for clearance/lighten/balance anyway as there was still vibes with what was sold to me as the correct series auto counterweight (will do the measuring check etc again but I want to port it anyway, will send to spinny bits to Freaky or Wilkins to machine) with after-market flywheel and there was an issue with leaking intake crossover o-rings/gasket filling housing with coolant too so I'm guessing it could be a bit messy inside. If you don't mind me asking Barry do you cut them with a fine diamond disk with a dremel style thing or is it more like a milling bit. I guess I'm curious as to whether there is a tight or open radius under the side seal and how hard it would be for me to replicate it, given sending you seals/rotor from Aus would be cost prohibitive and I'd like to try it myself anyway. Is there enough length in generic side seals to do this effectively? Last edited by Slides; 08-29-2015 at 08:56 PM..

Bookmarks

« Previous Thread | Top | Next Thread »

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is On Forum Rules

Forum Jump

All times are GMT -5. The time now is 08:47 PM.