NA SemiPP 20b

reddozen · 03-06-2017, 02:12 PM

Updated 6/4/2019

https://www.instagram.com/reddozen12/

Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one.

Goal 450WHP

Mazmart
B series motor purchased. Reliable source, and on the shelf.
Iron lapping

Built by Myles Fisher
Large Street Port, and semi pport
OE Seal kit
17pc Goopy 10mm stud kit
I-Rotay apex seals

Chip Motorsports
Rotor lightning, clearancing, and balancing 20b rotors
Going to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance.
Billet oil pan

Fabrication by Coffee Fabrication
Flaming River custom steering rack. Little faster ratio than stock
MK3 MR2 Electric power steering pump - eventually. May end up doing it myself.
370z transmission mounting.
Reverse mounted hood to open to the front - eventually

Drive-train / Engine Parts
Xcessive Engineering Short LIM
6x ID 1050 injectors
Adaptronic plug and play ECU
20b crossmember from Promaz
370z JK40C Transmission

Body
2012 Spirit R head lights
Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication)
Autoexe duck-tail trunk
Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts)
Lions Kit S2 over fenders - will replace with metal eventually.
Marsh Powerhouse Fabrication carbon zylon roof
RE Amamiya carbon tail lights
RE Amamiya AD Pro fender mirrors
Vertex Lang rear bumper
Vertex Lang side skirts (May change)

Misc Parts
Autoexe big brake kit
Autoexe S1 steering wheel
Autoexe ball type shift knob
90's Mazda Speed seats
Volk SF Challenge wheels

Johnny_K · 03-06-2017, 03:13 PM

Should be cool if this gets finished. You plan on passing emissions with this setup?

You have a target completion time frame.

reddozen · 03-06-2017, 03:23 PM

That's why we're keeping the stock ECU. If you turn off all the codes (AP, Mazda Edit or Racing Beat flash), and allow all the readiness checks to set, it should pass.

I have no clue on the time table... it's really up to all the hands it has to exchange, and just how far over budget it goes...

Best case... I would say September?

project86 · 03-07-2017, 10:00 PM

Quote:

Originally Posted by reddozen

That's why we're keeping the stock ECU. If you turn off all the codes (AP, Mazda Edit or Racing Beat flash), and allow all the readiness checks to set, it should pass.

Speaking from experience with the AP on my Speed3.... it doesn't let the readiness codes set. It masks the CEL but when they check at the emissions place it will say not ready and they will say "Did you disconnect your battery recently? You probably just need to complete your drive cycle."

Example:

I had the EGR removed and cat... EGR and cat both still said "not ready" after a full tune on the AP. You are allowed 1 not ready though.

FC Zach · 03-07-2017, 02:14 AM

Sweet man, look forward to seeing this completed!

almoststockfc · 03-07-2017, 07:27 AM

I set my goal for 6 months too, its now turned into 3 years lol. Be ready for setbacks along the way.

reddozen · 03-07-2017, 10:01 AM

Quote:

Originally Posted by almoststockfc

I set my goal for 6 months too, its now turned into 3 years lol. Be ready for setbacks along the way.

Believe me I know. We'll see where things fall. September is an absolute best case scenario. Things never work out for me quite so nicely.. lol

***TitaniumTT*** · 03-07-2017, 10:14 AM

Do I have to be the asshole?

Quote:

Originally Posted by reddozen

Best case... I would say September?

of 2019?

Quote:

Originally Posted by almoststockfc

I set my goal for 6 months too, its now turned into 3 years lol. Be ready for setbacks along the way.

And some not even by your own doing. Projects like that are never going to be top's on a shops list because they aren't money makers. They are in the sense that they're rolling advertisements, but the amount of time that fabrication takes and the amount that actually gets billed are two totally different numbers.

At Speed1 we would rather do engine jobs and dyno's all fucking day than the big project cars for the money, but the reality is if you can pull two blown REW's before lunch and bill 18.4 hours for it, you're gonna make a shit ton of money. But when you spend two days building an exhaust system, you're not actually going to bill 18 hours for it. Even if you do, you're still paying someone 18 hours and billing 18 hours, where if you can R&R an engine in a day, you'll pay someone 9 hours and bill 18.... so shops generally let the big projects sit until shit gets slow.....

Just my experience

Quote:

Originally Posted by reddozen

Believe me I know. We'll see where things fall. September is an absolute best case scenario. Things never work out for me quite so nicely.. lol

And lets not forget because Rotary

RETed · 03-08-2017, 02:55 PM

Quote:

Originally Posted by TitaniumTT

Do I have to be the asshole?

I'm STILL waiting for that Christopher W guy to get his 20B FC going...

Granted, he has the engine in the car, but I bagged on him like TWENTY YEARS AGO on the Evil Forum...

-Ted

GySgtFrank · 03-08-2017, 06:43 PM

Quote:

Originally Posted by RETed

I'm STILL waiting for that Christopher W guy to get his 20B FC going...

Granted, he has the engine in the car, but I bagged on him like TWENTY YEARS AGO on the Evil Forum...

-Ted

impatient you are.

reddozen · 03-27-2017, 09:12 AM

Myles picked the engine up from MazMart. Probably wont really be any updates till after DGRR.

rx7 vinnie · 03-07-2017, 11:06 AM

Sell it to me and let it sit for 5 more years.

FC Zach · 03-07-2017, 11:23 AM

Quote:

Originally Posted by rx7 vinnie

Sell it to me and let it sit for 5 more years.

Ain't that the damn truth, I still haven't seen your car!

rx7 vinnie · 03-07-2017, 12:20 PM

Quote:

Originally Posted by FC Zach

Ain't that the damn truth, I still haven't seen your car!

Unicorn bruh..... Unicorn.

reddozen · 03-07-2017, 01:11 PM

Like I said we'll just have to see.

03-06-2017, 02:12 PM	#1
reddozen Gold Wheels FTW Join Date: Mar 2008 iTrader: (0) Posts: 744 Rep Power: 17	NA SemiPP 20b Updated 6/4/2019 https://www.instagram.com/reddozen12/ Looking for a new eshaft. The original one is out of alignment, and in such a way that it cannot be straightened. This will not effect it's use, but the RPM limit has been limited to 8500 RPMs by Rick Engman. That doesn't work for the NA plans, so I need to find a new one. Goal 450WHP Mazmart B series motor purchased. Reliable source, and on the shelf. Iron lapping Built by Myles Fisher Large Street Port, and semi pport OE Seal kit 17pc Goopy 10mm stud kit I-Rotay apex seals Chip Motorsports Rotor lightning, clearancing, and balancing 20b rotors Going to have to do the 9.7 rotors now... lightning, balance, scallop, and clearance. Billet oil pan Fabrication by Coffee Fabrication Flaming River custom steering rack. Little faster ratio than stock MK3 MR2 Electric power steering pump - eventually. May end up doing it myself. 370z transmission mounting. Reverse mounted hood to open to the front - eventually Drive-train / Engine Parts Xcessive Engineering Short LIM 6x ID 1050 injectors Adaptronic plug and play ECU 20b crossmember from Promaz 370z JK40C Transmission Body 2012 Spirit R head lights Autoexe Type C hood (Will be replaced with a one off hood by MPH Fabrication) Autoexe duck-tail trunk Leg Motorsports RX Vision front bumper (Being remolded by MPH Fabrication into dry carbon with carbon zylon inserts) Lions Kit S2 over fenders - will replace with metal eventually. Marsh Powerhouse Fabrication carbon zylon roof RE Amamiya carbon tail lights RE Amamiya AD Pro fender mirrors Vertex Lang rear bumper Vertex Lang side skirts (May change) Misc Parts Autoexe big brake kit Autoexe S1 steering wheel Autoexe ball type shift knob 90's Mazda Speed seats Volk SF Challenge wheels __________________ My Cars: 1974 RX4 Coupe 1991 FC3S RX7 - Sold 2003 ZZW30 MR2 (Rotary swap after RX8) 2004 SE3P RX8 (20B Swap in the works) Last edited by reddozen; 06-06-2019 at 11:10 AM..

03-06-2017, 03:23 PM	#3
reddozen Gold Wheels FTW Join Date: Mar 2008 iTrader: (0) Posts: 744 Rep Power: 17	That's why we're keeping the stock ECU. If you turn off all the codes (AP, Mazda Edit or Racing Beat flash), and allow all the readiness checks to set, it should pass. I have no clue on the time table... it's really up to all the hands it has to exchange, and just how far over budget it goes... Best case... I would say September? __________________ My Cars: 1974 RX4 Coupe 1991 FC3S RX7 - Sold 2003 ZZW30 MR2 (Rotary swap after RX8) 2004 SE3P RX8 (20B Swap in the works)

03-07-2017, 02:14 AM	#5
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN iTrader: (2) Posts: 2,267 Rep Power: 19	Sweet man, look forward to seeing this completed! __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

03-07-2017, 07:27 AM	#6
almoststockfc ..... Join Date: Jan 2010 Location: Murfreesboro, TN iTrader: (0) Posts: 543 Rep Power: 15	I set my goal for 6 months too, its now turned into 3 years lol. Be ready for setbacks along the way. __________________ -75 RE_W_PU - -76 Hercules W2000 - DGRR 2012 3rd place Old School -75 Hercules W2000 MSO - DGRR 2011 Peoples Choice - April 2011 Rotary of the Month -Rotary snowmobile powered go kart - DGRR 2012 Peoples Choice - RIP

03-07-2017, 11:06 AM	#12
rx7 vinnie I SEE DEAD PEOPLE Join Date: Mar 2008 Location: nashville, tn (antioch) iTrader: (0) Posts: 743 Rep Power: 17	Sell it to me and let it sit for 5 more years. __________________ VIN-AUTO Rotary list of Fails below: 86 mazda rx7 csp 61 N/A= because RACECAR 87 mazda rx7 t2 with 13b-re cosmo GT42= FKN RUNS!!! 03 Dodge Viper SRT-10 Vert 06 dodge ram 2500 Megacab turbo Cummins=puller 16 MB ML350

03-06-2017, 03:13 PM	#2
Johnny_K Rotary Fanatic Join Date: Jun 2013 iTrader: (0) Posts: 225 Rep Power: 12	Should be cool if this gets finished. You plan on passing emissions with this setup? You have a target completion time frame.

03-07-2017, 01:11 PM	#15
reddozen Gold Wheels FTW Join Date: Mar 2008 iTrader: (0) Posts: 744 Rep Power: 17	Like I said we'll just have to see. __________________ My Cars: 1974 RX4 Coupe 1991 FC3S RX7 - Sold 2003 ZZW30 MR2 (Rotary swap after RX8) 2004 SE3P RX8 (20B Swap in the works)