PDA

View Full Version : ive been busy over the last few days :)

widebodyse7en
07-22-2011, 01:35 AM
so i thought id post since ive just recently rebuilt my motor with a streetport and goopy performance apex seals. i also used there housing refreshing service
heres a few pictures. tomorrow im finishing up with the oil pan and the front cover internals. enjoy!
widebodyse7en
07-22-2011, 01:37 AM
another picture
Signal 2
07-22-2011, 06:55 AM
Cool.
Curious....what prompted the rebuild? And how bad were your housings and how did they turn out?
widebodyse7en
07-22-2011, 09:58 AM
Cool.
Curious....what prompted the rebuild? And how bad were your housings and how did they turn out?

haha i blew my motor up in april and i only had a chipped apex seal. im going to give goopy performance props because they were like brand new when i got them back. they also installed my stationary gear bearings for free so that was cool

heres a picture of the housing before. i actually dont have a after but on there site they have lots that are what they looked like when i have them back.
Force13b
07-22-2011, 10:33 AM
Do you know what caused the chipped seal?
Signal 2
07-22-2011, 10:38 AM
Great. Been following customer's experiences with Goopy. I've got a couple used housings sitting on a shelf...~ 85k on them. No cracks or chatter marks and only light grooving. But some typical flaking on the edges. Wondering if they can be helped.
widebodyse7en
07-25-2011, 08:43 PM
Do you know what caused the chipped seal?

i actually dont know what caused it to chip since i was only boosting 5 psi at the time.

i sent goopy some housings that had 100k on them and they turned out really well.. im impressed. the only thing i had a problem with was the timing cover?.. it didnt quite fit which i thought was odd but i fixed that. anyway heres some more pictures.
widebodyse7en
07-25-2011, 08:46 PM
another couple pics also signal 2 those housings absolutley can be helped. :)
93rx7r1
07-26-2011, 05:31 AM
Looking good man! Nice to see a project coming together.
Force13b
07-26-2011, 10:27 AM
i actually dont know what caused it to chip since i was only boosting 5 psi at the time.


That's kind of scary. Always nice to find out what happened to keep it from happening again.
widebodyse7en
07-26-2011, 10:43 AM
That's kind of scary. Always nice to find out what happened to keep it from happening again.

lol yea i think it had more to do with the shitty oem 3 piece apex seals,,
widebodyse7en
07-26-2011, 10:44 AM
Looking good man! Nice to see a project coming together.

Thanks! it should be up and running later this week!
widebodyse7en
07-28-2011, 08:58 PM
got some more pics for you guys :P enjoy!
widebodyse7en
08-01-2011, 09:18 PM
heres some more pictures.. she is up and running just.. the clutch fork is flopping around in the bell housing for some reason..
widebodyse7en
08-08-2011, 11:18 PM
alright!.. its finally in running and now im tuning. heres a video of the set up

http://www.youtube.com/watch?v=n5U0UHLht5U
widebodyse7en
08-11-2011, 01:28 AM
kk so i decided to take some night pictures and i figured id post them for everyone.. not that it makes a difference lol.. no one comments or nothin haha anyway here they are!

http://www.youtube.com/watch?v=7G4ayCWCVoE