|
Old School Rotary Classified Pre- 1979 Rotary Classified |
Welcome to Rotary Car Club. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact contact us. |
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Premium Vendor
|
![]()
I'm selling my 1976 Mazda Cosmo (96210 miles) along with a spare parts car. Brake job recently done and car will pass inspection no problem.
It has the 4 port 13B which was rebuilt some time ago with all new seals and springs. Plates were ground, lapped and re-nitrided. Street ported intake and exhaust with NRS 3mm 2pc ceramic apex seals. An MSD runs direct fire to the leading plugs and the trailing runs off the distributor. 3 MSD blaster coils provide a powerful spark. OML racing plug wires (lowest resistance on the market) Breaker-less distributor is locked out with proper advance timing for best performance. IC reg built in alternator. High flow Carter fuel pump located in the trunk. Ceramic coated custom header with 1/8" wall tubing, ID matches the rotor housing port. Engine currently breathes through a modified Weber 51 IDA two barrel down draft racing carb. Carb was bought brand new as a 48 IDA and was then bored to 51mm with an enlarged float bowl and 3mm glass ball needle valve on a Tweak-it intake manifold from Australia. Cars can be sold with stock rebuilt carb and intake for $1000 less IE $4000.00 Or I can supply it with RB side draft manifold and 45 DCOE or 44 PHH or 50 DCO-SP, will negotiate price. The doors on the running vehicle are starting to rot through but the parts car has nice doors so no problem there. The parts car frame rotted at the steering box but could be easily repaired with a fish plate to get her on the road again. I have some extra parts that will go with them if wanted. Rotors, housings etc and any spare parts I have will go with them. I have 2 brand new windshields that will also go with the cars. Running car has cracked windshield but is still good for a long time before needing the windshield replaced. New windshield can be installed for free at Crackmasters in St. Albert. Summary of highlights: - 2 brand new spare windshields $950.00 Value - NRS 3mm 2pc Ceramic Apex Seals with twin Stinger hard faced springs $1400.00 value - 13B 4 port fully rebuilt with street ported intake and exhaust ports $3000.00 value - Port matched ceramic coated header - Modified 51 IDA Weber carb with enlarged float bowl and 3mm glass ball needle valve, jet extensions, air horns, K&N filter $1400.00 value - MSD direct fire on the leading plugs - 3 MSD Blaster coils - OML racing spark plug wires - Tweak-it intake manifold - High flow Carter fuel pump - IC reg built in alternator - Locked out breaker-less distributor - Brand new battery - Last new dash pad available from Mazda - RARE $5000.00 780-468-2567 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com Last edited by glassman; 06-10-2014 at 10:06 PM.. |
![]() |
![]() |
![]() |
#2 |
Premium Vendor
|
![]()
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
![]() |
![]() |
![]() |
#3 |
Premium Vendor
|
![]()
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
![]() |
![]() |
![]() |
#4 |
My minds tellin' me no...
|
![]()
Too bad getting 2 cars from Canada to Tennessee is a pain in the ass, or I'd buy them right now.
__________________
1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5 |
![]() |
![]() |
![]() |
#6 | |
Premium Vendor
|
![]() Quote:
![]()
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
|
![]() |
![]() |
![]() |
#7 |
The Newbie
|
![]()
Hey-
names Lewis 43- live in Florida at the Space Cost. Own two 1976 Cosmo's/RX5's. One's in good shape, the other's rough. Working on the good shape one first, not really sure about the second - using this one to help out with the first. Looking for a dash - who isn't, LOL Look forward to getting to know everyone - hope I can find other's who are as crazy as I am about these cars Lewis |
![]() |
![]() |
![]() |
#8 |
Premium Vendor
|
![]()
So are you jacking my thread to sell your car?
Your comments really don't belong in my FS thread
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
![]() |
![]() |
![]() |
#9 |
Premium Vendor
|
![]()
Guys please keep posts relevant to this car that is for sale, not Fred's, Bill's or one you saw at kfc
Thanks
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
![]() |
![]() |
![]() |
#10 |
Premium Vendor
|
![]()
Sold
__________________
Mild to wild, street to strip, when you want to go fast and you want your engine to last, NRS Ceramics is the only way to go. NRS Rotorsports nrsrotorsports@shaw.ca www.nrsrotorsports.com |
![]() |
![]() |
![]() |
#11 |
The Newbie
|
![]()
Hey everyone, I have an rx5 and I need help bringing it back to life, I need a manual trans with pedals from an rx5 or if someone knows a swap to replace trans let me know thks!. I have an 86 5 speed trans and a driveshaft but the driveshaft seems too short.
|
![]() |
![]() |