another 20b thread

1twistedrx7 · 12-24-2010, 10:29 AM

start off saying whats happening guys been really busy this past 6 months new shop to buying a new home with that being done .i made my mind that it was time to step up to the plate and do a 20b also a (13bre another thread soon). sort of a lil late on this thread because i have got to a point that i might as well start a thread now !

here is the scab

little more work done

week later!

the these came in so i put them up till the right time!

this also came in

for this to do a bridge port!

post more later have to to work now !!

1twistedrx7 · 12-24-2010, 06:45 PM

this is when she got a lil primer

now painted! pics have to do a couple of inside touch ups and a new windshield

1twistedrx7 · 12-24-2010, 06:50 PM

so today we finish the motor and installed it will post pics of the engine bay!

Santa did drop this off !

1twistedrx7 · 12-24-2010, 06:52 PM

another picture

jamespond24 · 12-24-2010, 08:45 PM

Looking good! So what mount did you use?

1twistedrx7 · 12-24-2010, 09:32 PM

sorry for any confusion but i installed a ported 3mm rotors 13b rew for now while i build my 20b .

I have checked for and did the proper clearances to have a little give for high boost levels and make sure that the rotor side seals ride the steels and not the rotors,and polished rotors to fight carbon build up but have one more to do !

I will post pics of the e shaft.

I am chafing the oil ports so that i can get oil all the way across the rotor bearings and not just the center of the bearing. What I am looking to accomplish is better oil flow for the rotor bearings and e shaft! I have done this mod to some 13b e-shafts as well that I am also considering to do to my 20b e-shaft, I am planning on removing the the spring and ball oiling mechanism. They are there for engine warm up process which is nice for a standard engine but because I plan on making high hp. I want the oil instantly so I will remove the spring and ball and install a webber 200 jet which will supply a sufficient amount of oil to key areas.
be back soon!

1twistedrx7 · 12-27-2010, 12:46 AM

been a busy bee but got one rotor done 2 two more to do for my 20b! here is a sneak peak!
scalloped rotors

timing @ TDC

and a lil suspension work

sway bars for the front and rear just for the twists at dgrr

T-von · 12-27-2010, 10:28 PM

What up? I'm suprised I actually came across this thread. Everything looks better on computer than on your cell phone. The rotors and polished e-shaft look nuts.

***Herblenny*** · 12-28-2010, 09:57 AM

Looking good! Hope to see it at DGRR

1twistedrx7 · 01-01-2011, 11:01 PM

oh will do my best to be there. Trying to get this 20b project done! I am building my own engine subframe not that bad at all. Today I got my jig done so it will be all true with steering rack, bottom clearance and stock shifter location. I have the engine in to mock up then start spot welding then back to the jig to finish the welds. I will try to post pics once the sub frame is complete .

1twistedrx7 · 01-10-2011, 01:25 AM

ok so the past week I have been really busy with the 20b sub frame so this is it !
first I was not wanting to hack my car and intake manifold and dry shaft.
so I installed the dry shaft, the power plant frame and the motor so that I would know where to start .I took the sub frame out and went to work this is what I came out with!

steering rack arms. oh ya you should wear safety glasses!

Drilling the holes to mount the steering rack.

1twistedrx7 · 01-10-2011, 01:30 AM

steering done

1twistedrx7 · 01-10-2011, 01:52 AM

so the sub frame is complete

So this came in !!!

starting tomorrow I will begin the rebuild on the 20b ! so far I have done rotor
clearances and scalloped rotors!!
I will be doing a bridge port on the secondaries. steal housings are in excellent shape.I will post pics of the bridge port then close it all up. then take it all out of the mock up car and install it into my black fd and begin wiring the micro tec lt-12s thanks ! be back soon enough.

1twistedrx7 · 01-10-2011, 10:29 PM

Definitely going to be at the rally this year Phil. If things go right we will have a couple 20b's going.

Started my partner Bobby's 20b build today also he is the master welder and fabricator behind our projects.

T-von · 01-11-2011, 04:04 PM

Looking good! Nice approach for the modified subframe. I can see how this will keep the factory rigidity once the rear portion is completed.

By the way, I have a nice thick piece of aluminum on the way so I can remake my oil pan. I rather not shorten the factory one.

Trey,

12-24-2010, 10:29 AM	#1
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	another 20b thread start off saying whats happening guys been really busy this past 6 months new shop to buying a new home with that being done .i made my mind that it was time to step up to the plate and do a 20b also a (13bre another thread soon). sort of a lil late on this thread because i have got to a point that i might as well start a thread now ! here is the scab little more work done week later! the these came in so i put them up till the right time! this also came in for this to do a bridge port! post more later have to to work now !! __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

12-24-2010, 06:45 PM	#2
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	this is when she got a lil primer now painted! pics have to do a couple of inside touch ups and a new windshield __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 12-24-2010 at 06:48 PM..

12-24-2010, 06:50 PM	#3
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	so today we finish the motor and installed it will post pics of the engine bay! Santa did drop this off ! __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

12-24-2010, 06:52 PM	#4
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	another picture __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 12-24-2010 at 06:55 PM..

12-24-2010, 09:32 PM	#6
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	sorry for any confusion but i installed a ported 3mm rotors 13b rew for now while i build my 20b . I have checked for and did the proper clearances to have a little give for high boost levels and make sure that the rotor side seals ride the steels and not the rotors,and polished rotors to fight carbon build up but have one more to do ! I will post pics of the e shaft. I am chafing the oil ports so that i can get oil all the way across the rotor bearings and not just the center of the bearing. What I am looking to accomplish is better oil flow for the rotor bearings and e shaft! I have done this mod to some 13b e-shafts as well that I am also considering to do to my 20b e-shaft, I am planning on removing the the spring and ball oiling mechanism. They are there for engine warm up process which is nice for a standard engine but because I plan on making high hp. I want the oil instantly so I will remove the spring and ball and install a webber 200 jet which will supply a sufficient amount of oil to key areas. be back soon! __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 12-24-2010 at 09:59 PM..

12-24-2010, 08:45 PM	#5
jamespond24 Rotary Fanatic Join Date: Feb 2008 iTrader: (0) Posts: 157 Rep Power: 17	Looking good! So what mount did you use?

12-27-2010, 12:46 AM	#7
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	been a busy bee but got one rotor done 2 two more to do for my 20b! here is a sneak peak! scalloped rotors timing @ TDC and a lil suspension work sway bars for the front and rear just for the twists at dgrr __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 12-27-2010 at 12:54 AM..

12-27-2010, 10:28 PM	#8
T-von Rotary Perfection Join Date: Dec 2010 iTrader: (1) Posts: 5 Rep Power: 0	What up? I'm suprised I actually came across this thread. Everything looks better on computer than on your cell phone. The rotors and polished e-shaft look nuts.

12-28-2010, 09:57 AM	#9
*Herblenny* Founder/Administrator/Internet Pitbull :) Join Date: Jan 2008 iTrader: (11) Posts: 644 Rep Power: 10	Looking good! Hope to see it at DGRR __________________ DGRR 2013 - Year of 13B www.DealsGapRotaryRally.com http://www.facebook.com/Herblenny

01-01-2011, 11:01 PM	#10
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	oh will do my best to be there. Trying to get this 20b project done! I am building my own engine subframe not that bad at all. Today I got my jig done so it will be all true with steering rack, bottom clearance and stock shifter location. I have the engine in to mock up then start spot welding then back to the jig to finish the welds. I will try to post pics once the sub frame is complete . __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

01-10-2011, 01:25 AM	#11
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	ok so the past week I have been really busy with the 20b sub frame so this is it ! first I was not wanting to hack my car and intake manifold and dry shaft. so I installed the dry shaft, the power plant frame and the motor so that I would know where to start .I took the sub frame out and went to work this is what I came out with! steering rack arms. oh ya you should wear safety glasses! Drilling the holes to mount the steering rack. __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

01-10-2011, 01:30 AM	#12
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	steering done __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com

01-10-2011, 01:52 AM	#13
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	so the sub frame is complete So this came in !!! starting tomorrow I will begin the rebuild on the 20b ! so far I have done rotor clearances and scalloped rotors!! I will be doing a bridge port on the secondaries. steal housings are in excellent shape.I will post pics of the bridge port then close it all up. then take it all out of the mock up car and install it into my black fd and begin wiring the micro tec lt-12s thanks ! be back soon enough. __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 01-10-2011 at 02:01 AM..

01-10-2011, 10:29 PM	#14
1twistedrx7 Rotary Fanatic Join Date: Feb 2008 iTrader: (11) Posts: 411 Rep Power: 0	Definitely going to be at the rally this year Phil. If things go right we will have a couple 20b's going. Started my partner Bobby's 20b build today also he is the master welder and fabricator behind our projects. __________________ Rotary Performance Motors(DGRRXI)sponsor 2011 RPM sale complete rebuilt your choice ported or bridge port short block W/RA seals 2300 no core required plus shipping. we now offer powder coating! 93 mb touring patring out sold! 93 vr touring sold 93vr died violently 93 ssm touring sold 93 black 20b project and a lot of money! underestimated !! http://rotorfest.lefora.com Last edited by 1twistedrx7; 01-10-2011 at 11:01 PM..

01-11-2011, 04:04 PM	#15
T-von Rotary Perfection Join Date: Dec 2010 iTrader: (1) Posts: 5 Rep Power: 0	Looking good! Nice approach for the modified subframe. I can see how this will keep the factory rigidity once the rear portion is completed. By the way, I have a nice thick piece of aluminum on the way so I can remake my oil pan. I rather not shorten the factory one. Trey, Last edited by T-von; 01-11-2011 at 04:08 PM..