Dgrr 2016

***TitaniumTT*** · 03-21-2016, 06:06 PM

Hoe Shit! Fuck that! Did you add extra grounds and use lots of dielectric grease?

reddozen · 03-22-2016, 08:39 AM

Quote:

Originally Posted by TitaniumTT

Hoe Shit! Fuck that! Did you add extra grounds and use lots of dielectric grease?

No extra grounds, but I had the greased them up good. I'm going to depin all the clips and scrub the hell out of all the tabs then crimp the female side so the pin will barely fit in. Also going to check the crimps on all the pins. Will probably just flow some solder into the crimped clips for good measure.

If this doesn't work, then I'm just going to drop the damn electric steering for a different rack. Probably use a Mark III MR2 electric motor.

***TitaniumTT*** · 03-22-2016, 09:27 AM

Don't use the solder, it will actually hinder with more resistance.

Sephitrask · 03-22-2016, 03:50 PM

Why the fuck did I even look in this thread? I knew it would just make me sad

Not going to make it this year, currently bleeding out on a rebuild on the 8 that won't be done in time, and even if the car was done wouldn't have the cash to make it happen. next year for sure the 8 will make a reappearance!

reddozen · 03-22-2016, 04:55 PM

Quote:

Originally Posted by TitaniumTT

Don't use the solder, it will actually hinder with more resistance.

Just re-crimp if it's loose?

***TitaniumTT*** · 03-22-2016, 05:08 PM

Yup. The crimps aren't what gets loose, it's the connector itself where the contact is made

djmtsu · 03-23-2016, 02:20 PM

http://rotarycarclub.com/rotary_foru...254#post327254

reddozen · 04-13-2016, 08:42 AM

Final count for online registration.. 197.

I'd say that we'll have about 250 people this year. It started out a little slow, but lots of people registered in the last month or so.

See everyone tomorrow!

chibikougan · 04-13-2016, 02:16 PM

Quote:

Originally Posted by reddozen

Final count for online registration.. 197.

I'd say that we'll have about 250 people this year. It started out a little slow, but lots of people registered in the last month or so.

See everyone tomorrow!

Nope but have FUN EVERBODY!

Pete_89T2 · 04-13-2016, 03:28 PM

Just finished detailing the FC and am ready to roll at the crack of dawn tomorrow.

See you all at the lodge!

chibikougan · 04-13-2016, 03:29 PM

Quote:

Originally Posted by Pete_89T2

Just finished detailing the FC and am ready to roll at the crack of dawn tomorrow.

See you all at the lodge!

Yeah this guy has my Motor...

Pete_89T2 · 04-13-2016, 03:39 PM

Quote:

Originally Posted by chibikougan

Yeah this guy has my Motor...

And if I ever get off my lazy arse, it will be built up, in my FC, broken in and tuned before next years DGRR

03-21-2016, 06:06 PM	#106
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Hoe Shit! Fuck that! Did you add extra grounds and use lots of dielectric grease? __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-22-2016, 09:27 AM	#108
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Don't use the solder, it will actually hinder with more resistance. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-22-2016, 03:50 PM	#109
Sephitrask BOILED PEANUTS!!! Join Date: Jun 2010 Location: Jacksonville, Fl iTrader: (0) Posts: 257 Rep Power: 15	Why the fuck did I even look in this thread? I knew it would just make me sad Not going to make it this year, currently bleeding out on a rebuild on the 8 that won't be done in time, and even if the car was done wouldn't have the cash to make it happen. next year for sure the 8 will make a reappearance! __________________ www.rotarycarclub.com *"The way a Rotary engine makes power is ferocious, much like having a chainsaw under your right foot."*

03-22-2016, 05:08 PM	#111
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Yup. The crimps aren't what gets loose, it's the connector itself where the contact is made __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-23-2016, 02:20 PM	#112
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	http://rotarycarclub.com/rotary_foru...254#post327254 __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

04-13-2016, 08:42 AM	#113
reddozen Gold Wheels FTW Join Date: Mar 2008 iTrader: (0) Posts: 744 Rep Power: 17	Final count for online registration.. 197. I'd say that we'll have about 250 people this year. It started out a little slow, but lots of people registered in the last month or so. See everyone tomorrow! __________________ My Cars: 1974 RX4 Coupe 1991 FC3S RX7 - Sold 2003 ZZW30 MR2 (Rotary swap after RX8) 2004 SE3P RX8 (20B Swap in the works)

04-13-2016, 03:28 PM	#115
Pete_89T2 Lifetime Rotorhead Join Date: Apr 2010 Location: Elkton, MD iTrader: (1) Posts: 874 Rep Power: 15	Just finished detailing the FC and am ready to roll at the crack of dawn tomorrow. See you all at the lodge!