TitaniumTT's I hope I make it to DGRR '09 Build - Page 54

helghast7 · 01-11-2010, 08:10 PM

Quote:

Originally Posted by TitaniumTT

I'm sure they are. The only place to find any real information on them is the manufacturers website. It's not under the general listing though, you need to DL or open thier PDF catalog. Everything else I've found is really just internet heresay, nothing really concrete as it applies to gas engines ..... everyone still guessing

yea thats as far as i got, the companies site only formally addresses the item for one car, but it looks like it would only work on that specific car

all other sites speak of it in past tense and dont say how to go about purchasing one or the type of setup they would run

and lol im trying to make this go as long as possible lol its getting hard

***TitaniumTT*** · 01-12-2010, 09:44 AM

The super secret tranny is assembled, it works, sorta, one problem to solve and one piece to be machined. Then it's off to Daves for some cryo treatment, full rebuild and then it can be put into the car. 6-spd, awesome gearing, and it fits in the stock shifter opening and BOLTS up to the bellhousing.

Roen · 01-12-2010, 10:23 AM

Curiouser and curiouser.......

need RX7 · 01-12-2010, 02:45 PM

I lol'd.

EJayCe996 · 01-12-2010, 05:01 PM

You should have done it as Count von Count from Sesame Street......

btw, where's mine?

need RX7 · 01-12-2010, 05:08 PM

Quote:

Originally Posted by EJayCe996

You should have done it as Count von Count from Sesame Street......

*awaiting new video with said revisions*

helghast7 · 01-12-2010, 07:30 PM

nice dude, cant wait to see it in the car

djmtsu · 01-12-2010, 07:48 PM

That vid make me LOL at work today.

***TitaniumTT*** · 01-12-2010, 08:23 PM

Quote:

Originally Posted by EJayCe996

You should have done it as Count von Count from Sesame Street......

btw, where's mine?

If you're serious, I can price some pieces out for you. I know exactely what needs to be done to make it work, and can get prices for everything with the exception of the machine work. I'll be heading down to the shop in the next few days to get some parts turned down.

Only drawback so far is there is no aftermkt short throw that I can find for it..... I may be making one of those too

Quote:

Originally Posted by djmtsu

That vid make me LOL at work today.

EJayCe996 · 01-12-2010, 11:15 PM

Quote:

Originally Posted by TitaniumTT

If you're serious, I can price some pieces out for you. I know exactely what needs to be done to make it work, and can get prices for everything with the exception of the machine work. I'll be heading down to the shop in the next few days to get some parts turned down.

Only drawback so far is there is no aftermkt short throw that I can find for it..... I may be making one of those too

Hell, tax returns are around the corner, why not?

I honestly don't have anything better to spend my money on other than that which automatically comes out of my paychecks into a Roth IRA

Force13b · 01-15-2010, 11:47 AM

Quote:

Originally Posted by TitaniumTT

If you're serious, I can price some pieces out for you. I know exactely what needs to be done to make it work, and can get prices for everything with the exception of the machine work. I'll be heading down to the shop in the next few days to get some parts turned down.

Only drawback so far is there is no aftermkt short throw that I can find for it..... I may be making one of those too

FD version?

***TitaniumTT*** · 01-15-2010, 12:12 PM

Quote:

Originally Posted by EJayCe996

Hell, tax returns are around the corner, why not?

I honestly don't have anything better to spend my money on other than that which automatically comes out of my paychecks into a Roth IRA

Alrighty, gimme some time to make sure that this thing is up to snuff, that the needed machining can actually be done, then I'll grab some parts fiches and price some stuff out.

***TitaniumTT*** · 01-15-2010, 12:15 PM

Quote:

Originally Posted by Force13b

FD version?

You would need to
change the clutch, maybe the flywheel,
starter
and worst off, modify the PPF as the tailshaft housing is most likely very different.
Speed sensors are another thing to worry about.

Yeah Jay, forgot to mention that, there's no speed sensor on this tranny. You'd need to use an aftermkt speedo with a programable hall effect sensor..........

Me, I got my MoTeC

Force13b · 01-15-2010, 12:26 PM

Quote:

Originally Posted by TitaniumTT

You would need to
change the clutch, maybe the flywheel,
starter
and worst off, modify the PPF as the tailshaft housing is most likely very different.
Speed sensors are another thing to worry about.

Yeah Jay, forgot to mention that, there's no speed sensor on this tranny. You'd need to use an aftermkt speedo with a programable hall effect sensor..........

Me, I got my MoTeC

That's a little much for a gear i doubt i need. I think i'll wait to see what you do with your FD, i'm sure you'll come up with something else. I'm sure my haltech could wire into a speed sensor of any kind just take some time to figure it out.

***TitaniumTT*** · 01-15-2010, 01:37 PM

Mag converter off of an ABS sensor

If the trans works well in the FC, I'll be doing the same thing with the FD. It's not an extra gear, it tightens up all the gears. You do loose some OD though. Im using the RX8 gear set, .84 OD FWIW. I think the ratio's will be spot on though. Especially the 1-2 & 2-3 shift.

01-12-2010, 09:44 AM	#797
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	Oh noes!!!!! I done it again! The super secret tranny is assembled, it works, sorta, one problem to solve and one piece to be machined. Then it's off to Daves for some cryo treatment, full rebuild and then it can be put into the car. 6-spd, awesome gearing, and it fits in the stock shifter opening and BOLTS up to the bellhousing. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

01-12-2010, 02:45 PM	#799
need RX7 Clean S4 Nutswinger Join Date: Mar 2008 Location: Sterling Heights, MI Posts: 485 Rep Power: 18	I lol'd. __________________ -Ted -1986 Mazda RX7 Sport [DD/beater]: engine finally let go at 205k. parts car status. -1986 Mazda RX7 base [resto-mod project]: S5 n/a swap in progress.

01-12-2010, 05:01 PM	#800
EJayCe996 PPP-P-P-P-POWER! Join Date: Feb 2008 Location: North GP, TX Posts: 283 Rep Power: 18	You should have done it as Count von Count from Sesame Street...... btw, where's mine? __________________ 1. Walk through a row of 22", or larger, rims 2. Say you love dubstep 3. ????? 4. PROFIT! Axiomatic: Total cacology.

01-12-2010, 07:30 PM	#802
helghast7 F yo couch! Join Date: Dec 2009 Location: Belleville, NJ Posts: 223 Rep Power: 16	nice dude, cant wait to see it in the car __________________ 87' n/a FC 94' FD-360whp, 300lbs-tq at 14psi on twins 92' ZZR-600 sold 07' CBR600RR more to come

01-12-2010, 07:48 PM	#803
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN Posts: 4,043 Rep Power: 22	That vid make me LOL at work today. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

01-12-2010, 10:23 AM	#798
Roen Evil Club Mod Join Date: Feb 2008 Posts: 183 Rep Power: 18	Curiouser and curiouser.......

01-15-2010, 01:37 PM	#810
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	Mag converter off of an ABS sensor If the trans works well in the FC, I'll be doing the same thing with the FD. It's not an extra gear, it tightens up all the gears. You do loose some OD though. Im using the RX8 gear set, .84 OD FWIW. I think the ratio's will be spot on though. Especially the 1-2 & 2-3 shift. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**