Whizbang's GSLSE

Whizbang · 06-03-2013, 08:37 PM

picked this up for a few hundred since the audi is being sold. ran rough, didnt want to start unless i poured gas on the filter, and had some low oil pressure. The engine is an S4 motor, recently swapped, and poorly. moving the distributor didnt change anything. sounds different than a one rotor situation, engine had even strong "poofs", and it has no power.

i think the low oil pressure is the front cover o-ring going to be taking a peek here this week.

I got all the S4 ecu, wiring, and sensor bits to just run the S4 stuff in an attempt to get the car running right. Began the process of making the S4 wiring harness ready for install... (hence the pile of wiring)

speedjunkie · 06-04-2013, 01:24 AM

Congrats! It looks great for the price.

Whizbang · 06-04-2013, 08:40 AM

Quote:

Originally Posted by speedjunkie

Congrats! It looks great for the price.

thanks Eric!

hows the springs been in my absence?

speedjunkie · 06-04-2013, 10:38 PM

Been pretty good here. Had some folks leave but more always move to town. When are you coming back? lol

Whizbang · 06-17-2013, 04:35 PM

well, trying to find an M12x1.5 bolt about 150mm long is completely impossible without waiting a week for two silly bolts. In leiu of doing that, im justing going to use an SAE equivalent. Not like you really need to drop subframes all the time.

So with that, today I should have the FC subframe installed. Just need to remove the rear studs, drill, and weld in the new stubs. Then viola!

Whizbang · 06-19-2013, 10:12 PM

FC subframing like it ain't no thing!

diabolical1 · 06-20-2013, 10:01 AM

looking pretty good so far.

fc nut · 06-21-2013, 09:01 PM

so... by using the fc crossmember, you can use the fc's rack n pinion? I'd do this to my beige se if I could use it.

Whizbang · 06-21-2013, 09:39 PM

Quote:

Originally Posted by fc nut

so... by using the fc crossmember, you can use the fc's rack n pinion? I'd do this to my beige se if I could use it.

yup, rack and pinion! i use the FC column as well. takes a little tinkering to make the column work out since that isn't a direct bolt in affair or anything.

but yea, basically i have the FC suspension, brakes, steering etc.

chibikougan · 06-22-2013, 04:00 AM

fc nut · 06-22-2013, 09:22 AM

would I have to modify the se's struts to work or modify the fc's?

Whizbang · 06-22-2013, 12:30 PM

FC struts. Then either FB tops with FB springs, OR FC coilovers (and top hats) by just widening the opening a wee little bit.

there will be pics

fc nut · 06-22-2013, 02:07 PM

concerning the steering column,do you combine the fc's wiring and the fb's to make it work? i'm assuming the fb column won't work with the fc rack? i have lots of questions.

Whizbang · 06-25-2013, 11:16 PM

some bits came in for the suspension

Whizbang · 07-03-2013, 09:32 AM

well I have some bad news bears:

I was cleaning the front cover to put back on then right about when i was done, I noticed a semi-circular chunk ground out of the inside.... uh oh. following Ted's comments about bearings and the nature of e-shafts to migrate I walked over to the motor. The front counter weight had a nice polished around on the edge, like it had been hitting something... uh oh.

but she still turned by hand nicely and I couldn't get any play by hand. So i used a small prybar between the counterweight and the front iron. And the whole shebang moved about 3/4"... oh uh... scratch that.... FUCK! at least that explains why the rear main seal was compromised.

So yea. car needs an engine... all because some fuckwad didn't torque the wee bolt holding the oil pickup properly and it basically came loose.

06-03-2013, 08:37 PM	#1
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	Whizbang's GSLSE picked this up for a few hundred since the audi is being sold. ran rough, didnt want to start unless i poured gas on the filter, and had some low oil pressure. The engine is an S4 motor, recently swapped, and poorly. moving the distributor didnt change anything. sounds different than a one rotor situation, engine had even strong "poofs", and it has no power. i think the low oil pressure is the front cover o-ring going to be taking a peek here this week. I got all the S4 ecu, wiring, and sensor bits to just run the S4 stuff in an attempt to get the car running right. Began the process of making the S4 wiring harness ready for install... (hence the pile of wiring) __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

06-17-2013, 04:35 PM	#5
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	well, trying to find an M12x1.5 bolt about 150mm long is completely impossible without waiting a week for two silly bolts. In leiu of doing that, im justing going to use an SAE equivalent. Not like you really need to drop subframes all the time. So with that, today I should have the FC subframe installed. Just need to remove the rear studs, drill, and weld in the new stubs. Then viola! __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

06-19-2013, 10:12 PM	#6
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	FC subframing like it ain't no thing! __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

06-21-2013, 09:01 PM	#8
fc nut member Join Date: Jun 2008 Location: Lebanon,Ohio iTrader: (0) Posts: 282 Rep Power: 17	so... by using the fc crossmember, you can use the fc's rack n pinion? I'd do this to my beige se if I could use it. __________________ leaving my carbon footprint....one start up at a time

06-22-2013, 09:22 AM	#11
fc nut member Join Date: Jun 2008 Location: Lebanon,Ohio iTrader: (0) Posts: 282 Rep Power: 17	would I have to modify the se's struts to work or modify the fc's? __________________ leaving my carbon footprint....one start up at a time

06-04-2013, 01:24 AM	#2
speedjunkie RCC Loves Me Not You Join Date: Mar 2008 Location: Colorado Springs, CO iTrader: (1) Posts: 2,089 Rep Power: 19	Congrats! It looks great for the price.

06-04-2013, 10:38 PM	#4
speedjunkie RCC Loves Me Not You Join Date: Mar 2008 Location: Colorado Springs, CO iTrader: (1) Posts: 2,089 Rep Power: 19	Been pretty good here. Had some folks leave but more always move to town. When are you coming back? lol

06-22-2013, 12:30 PM	#12
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	FC struts. Then either FB tops with FB springs, OR FC coilovers (and top hats) by just widening the opening a wee little bit. there will be pics __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

06-22-2013, 02:07 PM	#13
fc nut member Join Date: Jun 2008 Location: Lebanon,Ohio iTrader: (0) Posts: 282 Rep Power: 17	concerning the steering column,do you combine the fc's wiring and the fb's to make it work? i'm assuming the fb column won't work with the fc rack? i have lots of questions. __________________ leaving my carbon footprint....one start up at a time

06-25-2013, 11:16 PM	#14
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	some bits came in for the suspension __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

07-03-2013, 09:32 AM	#15
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	well I have some bad news bears: I was cleaning the front cover to put back on then right about when i was done, I noticed a semi-circular chunk ground out of the inside.... uh oh. following Ted's comments about bearings and the nature of e-shafts to migrate I walked over to the motor. The front counter weight had a nice polished around on the edge, like it had been hitting something... uh oh. but she still turned by hand nicely and I couldn't get any play by hand. So i used a small prybar between the counterweight and the front iron. And the whole shebang moved about 3/4"... oh uh... scratch that.... FUCK! at least that explains why the rear main seal was compromised. So yea. car needs an engine... all because some fuckwad didn't torque the wee bolt holding the oil pickup properly and it basically came loose. __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook