FC clutch slave thread size?

C. Ludwig · 08-30-2014, 06:39 PM

Can anyone check the thread size on the hydraulic fitting on an FC slave, please? TIA!

Dannobre · 08-30-2014, 07:14 PM

Not M10X1 like a lot of the others??

C. Ludwig · 08-31-2014, 11:52 AM

Nope. It's larger.

RETed · 08-31-2014, 03:45 PM

The fitting on the clutch slave cylinder to the clutch slave flex hose?
The one that uses a 17mm hex fitting to remove and install?
BTW, this is for a TURBO model...

I just eyeballed it, and it does look like a 10mm fine thread, or 10mm x 1.0.
The 10mm I got using a ruler.
I can confirm in a few hours, as I don't have my fastener measuring tools with me right now...

-Ted

C. Ludwig · 08-31-2014, 06:00 PM

Yes. Maybe it is 10mm. Thought it was larger. Turbo and NA use the same hose, so either one will give the proper measurement.

RETed · 09-01-2014, 04:23 AM

Confirmed.
10mm x 1.00

-Ted

C. Ludwig · 09-01-2014, 07:04 AM

Thanks Dannobre and Ted!

08-30-2014, 06:39 PM	#1
C. Ludwig Rotary Masochist Join Date: May 2008 Location: Floyds Knobs, IN iTrader: (5) Posts: 494 Rep Power: 17	FC clutch slave thread size? Can anyone check the thread size on the hydraulic fitting on an FC slave, please? TIA! __________________ _______________________________________________ *One stop Haltech, AEM, Syvecs shopping. Installation and tuning.* http://www.lms-efi.com *Free support. Drop us an email.* chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI

08-31-2014, 11:52 AM	#3
C. Ludwig Rotary Masochist Join Date: May 2008 Location: Floyds Knobs, IN iTrader: (5) Posts: 494 Rep Power: 17	Nope. It's larger. __________________ _______________________________________________ *One stop Haltech, AEM, Syvecs shopping. Installation and tuning.* http://www.lms-efi.com *Free support. Drop us an email.* chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI

08-31-2014, 06:00 PM	#5
C. Ludwig Rotary Masochist Join Date: May 2008 Location: Floyds Knobs, IN iTrader: (5) Posts: 494 Rep Power: 17	Yes. Maybe it is 10mm. Thought it was larger. Turbo and NA use the same hose, so either one will give the proper measurement. __________________ _______________________________________________ *One stop Haltech, AEM, Syvecs shopping. Installation and tuning.* http://www.lms-efi.com *Free support. Drop us an email.* chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI

09-01-2014, 07:04 AM	#7
C. Ludwig Rotary Masochist Join Date: May 2008 Location: Floyds Knobs, IN iTrader: (5) Posts: 494 Rep Power: 17	Thanks Dannobre and Ted! __________________ _______________________________________________ *One stop Haltech, AEM, Syvecs shopping. Installation and tuning.* http://www.lms-efi.com *Free support. Drop us an email.* chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-30-2014, 07:14 PM	#2
Dannobre Rotary Fan in Training Join Date: Oct 2008 iTrader: (0) Posts: 87 Rep Power: 17	Not M10X1 like a lot of the others??