SACHS Rotary engine revival

RICE RACING · 03-09-2013, 10:02 PM

Hello All,

Been too busy to post here much but wanted to share a video a few students of mine took at work.

2 years ago I found this engine in a bad state in our stock pile of teaching aids, it was very neglected and forgotten about, I undertook the task of knocking up a frame for it and restoring it.

Took off the govenor, made a race pipe, converted it to a hand throttle, and did a porting job on it. Overall the condition was not bad, had to machine up a few bits n pieces.

In our book room I managed to find the original dyno sheet and sales documents for the motor (which was purchsed from memory in 1967 from Rotor Power Australia *who were the Australasian Licence Holders for all SACHS prodcuts covering small engines and so on* I will try to scan this stuff and post it up at a later date.......... Flat out so dont hold your breath! between full time work and university study and doing rotary stuff and concuring the world with water injection my spare time is very precious!

Enjoy the video.

FC Zach · 03-10-2013, 05:24 AM

Very nice!

rx7 vinnie · 03-10-2013, 10:37 AM

Got a crick in my neck from it but cool video.

banzaitoyota · 03-10-2013, 08:43 PM

Nice

03-09-2013, 10:02 PM	#1
RICE RACING Don Mega Join Date: Dec 2008 Location: Utopia iTrader: (0) Posts: 1,688 Rep Power: 17	SACHS Rotary engine revival Hello All, Been too busy to post here much but wanted to share a video a few students of mine took at work. 2 years ago I found this engine in a bad state in our stock pile of teaching aids, it was very neglected and forgotten about, I undertook the task of knocking up a frame for it and restoring it. Took off the govenor, made a race pipe, converted it to a hand throttle, and did a porting job on it. Overall the condition was not bad, had to machine up a few bits n pieces. In our book room I managed to find the original dyno sheet and sales documents for the motor (which was purchsed from memory in 1967 from Rotor Power Australia who were the Australasian Licence Holders for all SACHS prodcuts covering small engines and so on I will try to scan this stuff and post it up at a later date.......... Flat out so dont hold your breath! between full time work and university study and doing rotary stuff and concuring the world with water injection my spare time is very precious! Enjoy the video. __________________ www.riceracing.com.au Worlds best Apex Seals Coil on Plug Water Injection ECU Calibration

03-10-2013, 05:24 AM	#2
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN iTrader: (2) Posts: 2,267 Rep Power: 19	Very nice! __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

03-10-2013, 10:37 AM	#3
rx7 vinnie I SEE DEAD PEOPLE Join Date: Mar 2008 Location: nashville, tn (antioch) iTrader: (0) Posts: 743 Rep Power: 17	Got a crick in my neck from it but cool video. __________________ VIN-AUTO Rotary list of Fails below: 86 mazda rx7 csp 61 N/A= because RACECAR 87 mazda rx7 t2 with 13b-re cosmo GT42= FKN RUNS!!! 03 Dodge Viper SRT-10 Vert 06 dodge ram 2500 Megacab turbo Cummins=puller 16 MB ML350

03-10-2013, 08:43 PM	#4
banzaitoyota Rotary Fanatic Join Date: Feb 2008 iTrader: (0) Posts: 201 Rep Power: 17	Nice __________________ My deuce

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode