Tips for cleaning up parts?

Raksj04 · 03-06-2012, 03:37 PM

I just got my 5 lug swap parts off a junk yard car. I wanted to clean them up a bit. Including the knuckle, which is a little rusty. I would like to powder coat it after I clean it up but that costs a lot. The main Issue I have is I live in the barracks, I have no garage. I can get to a shop but if I leave the parts over night I risk them walking away on me. I know there is a paint that a few guys used on transmissions and other driveline parts, however I forgot the name. Any help would be great.

WankelsRevenge · 03-06-2012, 05:28 PM

Paint wise I have no idea, however when I was doing alot of work on my FC had had tons of spare parts I would get some spray-on oven cleaner and liberally coat them, then toss them in the oven for a bit. Seemed to work great to me, of corse I only did this with engine parts so I'm not sure how it would work for what you have.
Ryan

vrracing · 03-06-2012, 07:03 PM

For your suspension components you might try Duplicolor Brake Caliper Paint or their wheel coatings. We have the red caliper paint on our calipers and after many years they still look great.

You might call ahead to the powder coaters and see if they can do it while you wait. Explain your situation and they might be accomodating. It doesnt take very long and since they cook it for 10 minutes or so you dont have to wait for it to dry, just cool down! If they wont do that they may be willing to sandblast the parts for you while you wait and then you can take them "home" to duplicolor them.

RETed · 03-06-2012, 11:51 PM

POR-15

-Ted

Raksj04 · 03-07-2012, 07:54 AM

What would be good for getting the rust off of the knuckle?

Raksj04 · 03-07-2012, 08:01 AM

Do any stores carry the POR-15?

Pete_89T2 · 03-07-2012, 10:00 AM

Quote:

Originally Posted by Raksj04

Do any stores carry the POR-15?

Not that I'm aware of, you buy online direct from the mfg.

www.por15.com

RETed · 03-07-2012, 10:13 AM

Just a word of warning with POR-15...
Use clothes that you'd throw away.
This stuff touches any fabic...it will never come out again.

-Ted

t_g_farrell · 03-07-2012, 11:16 AM

I'll just throw this out there. I needed to clean up a carb and found the
carb cleaner in the gallon can was so safe it could be used to water your
plants, needless to say it didn't work well. I then googled around and found
out that good ole lacquer thinner still has all the best ingredients the carb
cleaner used to have (acetone, etc). I bought a gallon and it work great.

I'm sure you could use this or the mentioned oven cleaner for the first pass
and then a good soak in alcohol will get it ready to paint. For rust you can
use a wire brush and then a rust converter or rust converter paint like POR-15
or Rustoleum. Depends on your budget.

(1st gen guys now ducks and runs out of 2nd gen section)

Raksj04 · 03-07-2012, 01:06 PM

Thanks for the help. I would buy off line but shipping to base is a pain. Takes 2 to 3 days longer for me to get it.

LuckySeven fc3s · 03-07-2012, 02:01 PM

ship it to me and i can just drive it out to you

WankelsRevenge · 03-07-2012, 03:26 PM

Which base are you at? I live about a mile from the mayport one
Ryan

Raksj04 · 03-07-2012, 03:43 PM

NAS, near orange park.

Sharingan 19 · 03-12-2012, 03:40 AM

All these Jax Rotaries popping up, thats encouraging.

LuckySeven fc3s · 04-05-2012, 11:10 PM

if only you knew...

03-06-2012, 03:37 PM	#1
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 14	Tips for cleaning up parts? I just got my 5 lug swap parts off a junk yard car. I wanted to clean them up a bit. Including the knuckle, which is a little rusty. I would like to powder coat it after I clean it up but that costs a lot. The main Issue I have is I live in the barracks, I have no garage. I can get to a shop but if I leave the parts over night I risk them walking away on me. I know there is a paint that a few guys used on transmissions and other driveline parts, however I forgot the name. Any help would be great.

03-06-2012, 07:03 PM	#3
vrracing Rotating Assembly Join Date: Oct 2008 Location: TX iTrader: (0) Posts: 102 Rep Power: 17	For your suspension components you might try Duplicolor Brake Caliper Paint or their wheel coatings. We have the red caliper paint on our calipers and after many years they still look great. You might call ahead to the powder coaters and see if they can do it while you wait. Explain your situation and they might be accomodating. It doesnt take very long and since they cook it for 10 minutes or so you dont have to wait for it to dry, just cool down! If they wont do that they may be willing to sandblast the parts for you while you wait and then you can take them "home" to duplicolor them. __________________ 90 S5 Vert. JDM Tii with BNR Stage1 turbo. Pineapple Racing street port. Bonez cat-forward. Corksport cat-back with Vibrant UltraQuiet resonator. RTek 2 wZeitronix w/b. HKS EBC. Vis CF Tii hood. 3000GT wing. Ground Control coilover kit with KYB AGX shocks. Red and Black leather RX8 seats. Corksport Odura lip & bumper caps, OEM Tii skirts

03-07-2012, 11:16 AM	#9
t_g_farrell Waffles - hmmm good Join Date: Aug 2008 Location: Huntersville, NC iTrader: (0) Posts: 757 Rep Power: 0	I'll just throw this out there. I needed to clean up a carb and found the carb cleaner in the gallon can was so safe it could be used to water your plants, needless to say it didn't work well. I then googled around and found out that good ole lacquer thinner still has all the best ingredients the carb cleaner used to have (acetone, etc). I bought a gallon and it work great. I'm sure you could use this or the mentioned oven cleaner for the first pass and then a good soak in alcohol will get it ready to paint. For rust you can use a wire brush and then a rust converter or rust converter paint like POR-15 or Rustoleum. Depends on your budget. (1st gen guys now ducks and runs out of 2nd gen section) __________________ 1980 GS stockport, Fat Nikki, RB Dual Facetfuel pumps, Holley regulator, RB Street port exhaust, 2GDFIS, MR2 MK I electric fans, 2G strut bar, relayed fans, lights and fuel pump, LEDs Project Fat Nikki Budget 12A rebuild Video setup < $30.00

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-07-2012, 07:54 AM	#5
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 14	What would be good for getting the rust off of the knuckle?

03-07-2012, 08:01 AM	#6
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 14	Do any stores carry the POR-15?

03-07-2012, 01:06 PM	#10
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 14	Thanks for the help. I would buy off line but shipping to base is a pain. Takes 2 to 3 days longer for me to get it.

03-07-2012, 02:01 PM	#11
LuckySeven fc3s fc3s_nataku on rx7club Join Date: Apr 2009 Location: OrangePark FL iTrader: (0) Posts: 35 Rep Power: 0	ship it to me and i can just drive it out to you

03-07-2012, 03:43 PM	#13
Raksj04 I have Ultra power in me. Join Date: Sep 2011 iTrader: (2) Posts: 457 Rep Power: 14	NAS, near orange park.

03-12-2012, 03:40 AM	#14
Sharingan 19 Rotary Fanatic Join Date: May 2010 iTrader: (0) Posts: 138 Rep Power: 15	All these Jax Rotaries popping up, thats encouraging.

04-05-2012, 11:10 PM	#15
LuckySeven fc3s fc3s_nataku on rx7club Join Date: Apr 2009 Location: OrangePark FL iTrader: (0) Posts: 35 Rep Power: 0	if only you knew...