DGRR 2011 Winners

[butterfly21kaye]

Doing this from memory, so correct me if I'm wrong!

Best of Show:
Rich Farrell (GoodfellaFD3S)

Old School:
RotoryPolo (Marco)
SavannaDan
Buggy (Bryon K)

RX-8:
Kane Tomlin
Fisher (Ryan P.)
Chad D.

1st gen:
Robert Watson
el canito rotary
CorgiSteve

2nd gen:
TitaniumTT (Brian T.)
Pete_89T2
bikerboy_23322 (Shane)

3rd gen:
Scrub (Dan McVicker)
Trout2 (Jack Coxe)
Supernaut (Andy)

V8:
evot23 (Eddie)
Red V8 on trailer
lt1_fd3s (Tray Houston)

[butterfly21kaye]

Post pics and mods of your winning car here.

[evot23]

sorry for the repost on the pic...best one I have

Eddie Vergara
2002 LS6 mild cam 412rwhp/405 trq
Mods...hmmm
Shine Sanai Front and sides
Shine Craftsquare replica rear cannards
Shine Street Diffuser
RZ Recaros
Feed Gauge cluster
Feed Rear tower brace
Feed Luggage tub
Improved Racing Front Tower Brace
S2K push button start (lol)
R-Magic Lights
RSR coilovers/springs
Old school Enkei RP01 18x9 front 18x9.5 rear
RE-Amemiya GTII low spoiler

[Sephitrask]

I WANT THAT SPOILER!

[Kane]

Kane
2007 Mazda RX-8, Ported, Ceramic Sealed and Turbocharged









Powertrain / Tuning:
* All power modifications stealth installed, goal is to keep engine bay looking 100% stock *
13B-MSP Ported and Hand Built by Black Halo Racing
Ceramic 2mm 1-piece Apex Seals from NRS Rotorsports
Rotors Milled by Speedsource
Black Halo Racing / Spec Stage 2 Clutch
Mazmart Waterpump
Powder coated all Pulleys Piano Black
Greddy Manifold, Down pipe, Intercooler and Intake Piping (powder coated stealth black)
Custom Garrett GT3071R Turbo by Mazda Maniac
Synapse Syncronic BOV - recirculated like a real man...
Custom AEM Air Intake with K&N Filter hidden in bumper
Greddy SP2 Catback Exhaust with gutted cat and resonator
New Flow-matched 400cc, 400cc and 800cc Injectors (brings total fueling well in excess of 400WHP)
Black Halo Racing's 3 Core Aluminum Radiator by Griffin
Agency Power Silicone Radiator Hoses
Cobb Accessport PCM Flash Tuner
Custom Tuned by PPO2's automated tuning software; Baseline
Stealth Oil Catch Can fabricated from OEM Air Pump
Greddy Front and Rear Strut Tower Brace (powder coated stealth black)
Black Halo Racing's Yukon Coil Ignition System

Suspension / Braking:
Tein Coilovers
Prototype KVR 2-Piece Slotted Rotors, Aluminum Hats and Hawk Ceramic Pads
Agency Power SS Brake Lines
Gorilla Blue Racing Lug Nuts

Interior:
Greddy Turbo Timer and Profec II Boost Controller
Autometer Cobalt AFR, Boost and EGT in Lotek dash pod, custom molded to center console, Piano Black
Autometer Elite Fuel Pressure Gauge in Vent Pod from BlockHead
iPod Integrated into Bose system
Hymee Scanalyzer Live for the ODBII Info
PPO2 White Retro Shift Knob custom counter-weighted by Koolknobs
Custom Center Console and Head Unit w/ remote mount Radar & Laser Detector
Italian Leather Shift Boot and Arm Rests from Shiftstyle

Exterior:
Authentic Mazdaspeed Full Bodykit
19" Staggered (9.5"+28mm rear, 8.5"+35mm front) SSR D5R Wheels on Federal Tires w/ Fender Roll and Stretch
35% Tint on windows; 5% Tint on sunroof
Fender Vents Paint Matched to Wheels in Top Secret Gold

Sponsors:
Ron's Performance
JN Mazda
PPO2 Performance
Street Unit

Awards Won:
Top Mazda Car Domain, 1st Place DGRR RX8

[Buggy]

Buggy (Bryon K) 1976 Rx-4


Mods:
-Half Bridge 13B 3B 4 port
-S5 NA rotors
-Rx-8 Stationary gears, bearings, and eccentric shaft
-FD oil press. regulator
-Weber 48 IDF carburetor and manifold
-Racing Beat road race header, presilencer, and 3" muffler
-FC front mount oil cooler
-Braided stainless oil cooler lines
-Carter fuel pump and holley FPR
-Aluminum fuel cell
-DLIDFIS ignition
-Racing Beat aluminum flywheel and ACT clutch
-Pedders Suspension front coil springs
-Autometer pro comp marine oil press., coolant temp, and 10k RPM tach.
-Hand built front bumper. (made from a 1993 chev truck bumper)

Off the top of my head that's all I can remember. There's some I'm missing though I'm sure.

[Rotorypolo]

Rotorypolo 1973 RX-3
1st in class (old school/other rotaries) DGRR 2011






Mods
Here is everything in a nutshell:
Street port 13B 4 port, MSD Ignition coils and Jacobs amp, Holley 4 barrel carburetor, Holley fuel pump, Racing Beat intake manifold, Racing Beat downpipe, Racing Beat exhaust system. Custom built 5 speed TII transmission with gear changed out and shorten gearing. Custom race suspension with coilovers and 4 wheel disc brakes w/ cross drilled rotors. Everything under the hood is SS lines and AN fitting. Chassis was stiffened and reinforced. Wheels are ultra rare Advan Racing A3A. 13 x 8s. Interior is mostly stock with an RX-8 GT seat for the passenger side and an old school Sparco racing seat for the driver.

[butterfly21kaye]

Marco, where was the photo in front of the waterfall taken?

[Rotorypolo]

Originally Posted by butterfly21kaye

Marco, where was the photo in front of the waterfall taken?

we went on the Friday morning Skyway run and did a little detour to check out that neat waterfall. It was beautiful )

[whiteboy's rx7]

Shane Duncan
1987 TII Rx7
( Whiteboy's Rx7 )
3rd place FC












Interior :
clean and all working
momo tuner steering wheel with adapter
mazdaspeed leather shift knob
double din, new speakers
prosport boost gauge, aem wideband

Exterior:
repainted
S5 mirrors, Spoiler, Tails
15% tint
626 Lower lip
FD rx7 wheels gunmetal with spacers
Blue calipers

Engine/ small mods :
In House

Fresh rebuild
3mm rotors
3mm apex seals
Solid corner seals
93+ corner springs
Pineapple Racing street port intake and exhaust
Fly cut housings for spark plug clearance
Oil pressure mod
Eliminated OMP, plugged holes
Solid thermal pellet
Port matched manifolds
Pineapple racing Timing cap

CAI plate, Specter filter
Turbo oil filler cap
Relocated battery
Knightsports dual alt pulley
Allen head hardware
Polished steel pulleys cleared
Koyo Radiator
Removed emissions, with block off kits

Performance

BorgWarner GM8
HKS manifold
t4-t3 adapter
Tial 41mm WG, stainless wg pipes
Tial 50mm BOV
CX racing piping, hand fit
CX racing intercooler
TB elbow
stainless turbo lines
Marren 720/1000 cc injectors
g35 fuel pump
3in down pipe (heat wrapped),
Trust sp exhaust.
Rtek 2.1 ecu
6 puck sprung clutch
mazdatrix short shifter

[Supernaut]

[rwatson5651]

Robert Watson
1st in Class- 1st Gen
Exterior:
Pacific front and rear spoiler, sideskirts
Aurora White Paint (Painted at home)
BBS 15x7 Wheels

Engine:
13B4port Streetport
Built at home with 12a irons
Balanced rotating assembly
Mikuni 44pph sidedraft carb with modded accel pump, Mallory comp 70 pump and regulator
Racing Beat streetport header with streetport midsection and powerpulsemuffler.
High volume oil pump with high pressure mod
modded OMP with 2 cycle oil tank
relocated oil cooler with Racig Beat oil lines and full length radiator
MSD 6A Direct Fire setup

Suspension:
Respeed rack and pinion, coilovers, camber plates, and Respeed anti sway bar
(My favorite part of the whole car!)

Interior:

Custom leather interior stitched by Shannon Walters, Alex City AL with suede headliner and suede accents, custom dash panel with OE style guages

[Trout2]

Jack Coxe - 3rd gen - 2nd place

1994 Mazda Rx-7 with Popular Equipment Package with approx. 111,000-miles modified by myself with mucho assistance from Gorilla RE

Engine:
RP/rx7.com street port, 3mm apex seals, balanced rotating assembly
Unorthodox anodized full pulley set (main, w/p, alt)
Mazdaspeed engine mounts
Garfinkle oil pan brace

Intake:
Ground Zero / Excessive lower intake manifold (with Gorilla RE extra injector bung plugs)
Gorilla RE upper/lower intake manifold port matching
Gorilla RE ported throttle body
Double-throttle – AWS – wax rod removed
All unused Upper Intake nipples removed/plugged
Jet Hot cerama-chrome coating upper/lower intake manifolds
Turbo Blown LIM heat shield blanket
Sport Tuner throttle body polishing with nickel plated linkage

Turbo:
A-spec 500R with long runner manifold (Gorilla RE prepared: smoothed compressor inlet, rough casting – welds – flanges – protruding bolts ground smooth)
Tial 44mm waste gate
Gorilla RE 1-3/4 inch waste gate dump tube
Tial 50mm blow off valve
Blitz sbc-id boost controller
Earls -4 & -6AN super stock hose & fittings for water, W/G & BOV lines
ATP -3AN stainless steel oil feed line
Earls -10AN Perform-O-Flex stainless steel oil return line with swivel seal fittings
K&N air filter with Gorilla RE 45 degree aluminum inlet pipe & 45 degree blue silicone coupler
Sport Tuner high-temp black ceramic coating exhaust manifold & turbine housing
Sport Tuner cerama-chrome compressor housing
DEI black fire sleeved oil, coolant, & wastegate lines
Thero-tec heat sleeve a/c lines & misc. wires
Thermo-tec adhesive backed heat shielding on fire wall, ABS shield and inner fender

Intercooler:
Crooked Willow stock mount IC (Spearco 13x17-in. core with carbon fiber duct)
Gorilla RE polished aluminum piping
Greddy throttle body elbow
Hose Techniques blue silicone couplers with Breeze clamps

Exhaust:
Gorilla RE 4-inch stainless steel downpipe
RP/rx7.com - Greddy 3-3/4 inch race exhaust
DEI titanium wrapped downpipe
DEI fiberglass wrapped mid & rear muffler sections
Thermo-tec muffler shield on mid-muffler
Fuel System:
Injector Dynamics 725cc primary / 2000cc secondary injectors
KG fuel rails with Sport Tuner cerama-chrome coating
SX Performance fuel pressure regulator with -3AN stainless steel boost line
Apexi BNR33 pump
Chuck Westbrook fuel pump wiring mod (direct power to relay, 10-ga. power wire from fuel pump relay to pump, extra ground at pump)
Earls -6AN feed/return Perform-O-Flex hose with swivel seal fittings (routed using Earls hose separators mounted on OEM feed/return brackets undercar)
Hyperion surge tank cover
Kinsler ANO-BRL 10-micron in-line fuel filter

Ignition:
HKS Twin Power amplifier
Turbo II leading coil
Magnacore 10mm wires
Gorilla RE remote coil mount bracket (in place of removed power steering pump)
NGK R7420-9 & 10 spark plugs

Engine Management:
Apexi Power FC with commander
FC datalogit
Dudeman fast acting air intake temperature sensor relocated to intercooler outlet pipe
Gorilla RE tuning
Race Logic traction control
OEM map sensor with -4AN super stock hose and fittings

Cooling:
Koyo radiator
Mazmart remedy water pump
Evans coolant
FC thermo switch
Thermo-flex radiator hoses
Earls -4 & -6AN super stock hose & fittings
Sport Tuner cerama-chrome water pump & thermostat housings
OEM polished coolant filler cap

Oil System:
Crooked Willow dual oil cooler kit using Mocal 19-row coolers, Mocal thermostat, Aeroquip -10AN lines & fittings, carbon fiber ducts
RE-Speed oil filter pedestal adapter with -10AN outlet & gauge ports (passages ported by Gorilla RE)
Gorilla RE bell-mouth modified pick-up tube
Gorilla RE aluminum OMP oil supply block off plate
Earls -3AN hose/fittings for premix supply to Gorilla RE modified OEM oil metering pump
Afgmoto1978 black pre-mix tank in place of OEM vacuum canister
RE-Speed filler neck
Valvoline 10W-30 VR-1 motor oil
Idemitsu Racing rotary synthetic pre-mix
Jaz 1-pint breather can on Gorilla RE bracket with -4AN super stock hose & fittings to oil filler neck & rear iron’s unused oil drain

Instrumentation:
SPA oil pressure/temperature gauge
SPA water temperature/fuel pressure gauge
PLX egt gauge using Temp Rip sensors in turbo manifold
Innovative XD-19 wide band gauge and sensor with Gorilla RE aluminum heat sink
Defi D-gauge mechanical boost gauge

Electrical:
Odyssey PC925 battery in passenger side rear bin with Jegs aluminum battery tray mounted to Gorilla RE bracket that uses existing rear seat belt mounting points
Gorilla RE bracket for OEM battery fuse box
Phoenix Gold 200-A circuit breaker at battery
Phoenix Gold 1/0 positive & negative battery cables (both routed battery to starter, positive from starter to main fuse box)
Phoenix God 4-gauge ground cables at numerous points
OEM engine harness (unused wiring removed, re-wrapped with split loom, fusing tape, electrical tape, exposed portions wrapped with Thermo-Tec heat shield tape)
Sport Tuner 140-Amp alternator, cerma-chrome coated, blue painted stator

Wheels/Tires:
Volk SE37A 18x9.5 (F+45 /R+45 with 5mm spacer) powder coated black
Falken RT-615 265-35-19 F/R tires
Muteki black lug nuts

Suspension:
Aragosta 15-way adjustable dampers with 10.3/7.8-kg F/R springs
Suspension Techniques F/R sway bars
Improved Racing adjustable sway bar end links
Widefoot front sway bar mounts
RP/rx7.com trailing arms
M2 toe links
Cusco front strut tower brace

Drivetrain:
Atomic Rex manual steering rack
Exeddy D-core twin disk carbon clutch
RP/rx7.com stainless steel clutch line
Mazdaspeed short-throw shifter
Pettit 80-durometer differential mounts
NEO 75W90 synthetic gear oil in transmission & differential

Brakes:
Stop Tech front big brake kit with piston sized to match 99-spec rear & slotted rotors
99-spec OEM rear calipers with Precision 2-pc slotted rotors
Mazda 929 master cylinder
N-Tech front rotor backing plates
Stainless steel lines (Stop Tech front / rx7.com rear)
Motul RB-600 Brake fluid
Rotary 13B1 anodized blue rotor shaped brake/clutch fluid reservoir cap

Exterior:
Original Chaste White Paint
Shine replica Mazdaspeed front lip
Shine replica RE-A street diffuser
Front lip and diffuser sanded then coated with Dupli-color truck bed liner
OEM mud guards
Smoked front turn lamp housings
LED tail lights, marker lights, turn signals, reverse lights, license plate lights
20% rear / 50% side window tint
PIAA platinum series super white headlight bulbs

Interior:
Original 1994 unless otherwise mentioned
Mazdaspeed Type F seats recovered in BMW black leather
Momo Super Anatomic shift knob
Momo Monte Carlo 350mm steering wheel
Flyrx7 3-gauge 52mm center speaker gauge pod
Saab 3-gauge 52mm din panel
RE-Amemiya Steering column gauge pod
Redline.com black leather shift & parking brake boots
JDM armrest ashtray replacement
TNT rear hatch carpet

Misc:
Himni Racing stainless steel hardware throughout engine bay
Black powder coated brackets, hard water & brake lines throughout engine bay
Aba stainless steel hose clamps for air filter & wastegate lines

[Kane]

^^^ I remember that FD, stupid clean ride man!

[TitaniumTT]

Brian Treffeisen

1988 Mazda RX7 Originally a 4-lug SE Chassis has approx 260ishk

Pretty much bone stock

All mods including paint performed by myself, tuning done by Dave @ KDR/Speed1, Mazpower of Illicit Performance, and myself

Engine:
13B-RE cosmo engine. Proprietary intake ports and exhaust porting
RWS OMP adapter
New OEM side/ corner seals
RA Super Black Cryo seals
Proprietary clearances
RX8 e-shaft and stat gear bearings
ALL internals cryo treated

Intake:
Ported and portmatched intake mani
Custom Elbow
Ceramic Coated by Sport Tuner
Double-throttle – AWS – wax rod removed
All unused Upper Intake nipples welded shut
All -3 braided line used for MAP sensor and FPR (I'm adding a "vacuum block" as I type)

Turbo:
BNR Stage 3's
Custom Y-pipe
Custom X-over pipe
Custom Rob Bailey Solenoids
Custom Boost and Vac tank
All run sequentially via the MoTeC M800

Exhaust:
Started off as an ebizzle REW DP
Added 3" flex coupler
ALL SS V-bands
Magnaflow 3" in 2x 2.5" out as a "mid-pipe"
Magnaflow 2.5" in/out can
Summit Special exhaust tips becuase... well, the Magnaflow and borla tips were more expensive than thier mufflers... thank you ricers!

Fuel System:
Injector Dynamics 725cc primary / 2000cc secondary injectors
CJ Motorsports primary rail/Rotary Extreme Secondary
Bosch Motorsports FPD
Aeromotive "mini" adjustable FPR with -3AN SS reference line
Custom 17gal fuel cell with Cosmo Lift pump and a "Poopra" 290lph pump stuffed in a built in surge tank.
-6 SS hardline replaces all the stock crap and -6 Nomex taking care of all the needed flex line
Aeromotive 10 micron fuel filter

Ignition:
Bosch Motorsports coils Modified by Paul Yaw

Engine Management:
MoTeC M800 ECU
MoTeC TCMux Traction Control Multiplexer
AIM Digital Dash
Boost Trim Switch
Lauch Control and Traction Control
Full Fuction Engineering "one-off" Trigger kit for my REW hub and RE front cover w/Hall-Effect Sensor (damn I love that thing)

Cooling:
Custom Griffen Radiator.... at this point I've done more welding on that thing than they have
-16 fittings
Custom AST with inlets from the engine and the rad
Proper ducting from the bumper
I have 0 hose clamps on my entire engine and only 2 for the heater core
Rad Mounted to a custom HMIC frame that houses the Rad/Intercooler and all the ducting. Can be removed with 10 bolts and is strong enough to stand on

Oil System:
Dual Mocal 19-row coolers,
Mocal thermostat
Aeroquip -10AN Nomex lines & fittings
Custom ducting
THE FIRST EVER RE-Speed oil filter pedestal adapter with -10AN
Custom oil filler neck with vacuum port scavenger into exhaust
Passageways ported
Custom o-ringed oil pump

Instrumentation:
AIM digital dash
AutoMeter Boost, Fuel and voltometer

Electrical:
Battery relocated into custom Billet tray
Remote Batter cut-off switch
MoTeC, Alarm, PW, PDL, Trunk solenoid, Horn and siren all hard wired
Remote Jumper and charge ports

Wheels/Tires:
Work VSXX 17x8 and 17x9 +35 wheels
Dunlop Direzza Z1SS in 235/40 255/40/17

Suspension:
Stance C/O's with 7/5 springs
RB fron Sway Bar
RB endlinks
Rear bar removed
All Poly bushings
Camber adjuster in the rear
DTSS eliminators
Custom tri-point strut bar with engine torque brace
Custom Rear strut bar
Custom Lower Arm Bar
did I mention I like building custom things?
Custom Bumper support and HMIC frame Brace

Drivetrain:
TitaniumTT modified 15:1 De-Powered Powersteering rack
4.3 Torsen Rear end
Exedy Twin Disc Clutch
6-spd Tranny (Yes I'm counting this )
Custom AL driveshaft

Brakes:
Custom Wilwood setup Front and Rear THANK YOU FASTBRAKES!
13.25"x 1.25" front rotors
6 Piston Wilwood Superlite Calipers
12.2"x.81" Rear rotor
Wilwood Combination P-Brake caliper - yes, I have a functioning ebrake
New pads coming
Wilwood 1" remote mount Master Cylinder
Custom adater to keep power brake booster
Wilwood combination Proportioning Valve
I redid EVERY SINGLE line in 3/16" Stainless Steel hardline
Custom -3 SS braided softlines to go to the calipers

Exterior:
Custom paint color based of the original Lotus Storm Titanium Metallic
Shine auto Front bumper heavily modified and reenforced
Full S5 molding conversion
Custom painted S4 Rear Tail lights
Carbon Fiber exhaust Gaurds
Smoked all outside lenses
5% tint all around
Illicit Perfomance Sticker
Custom hood - Yes, I built that hood starting with a stock aluminum hood

Interior:
Herblenny's old RX8 seats
New carpet
Custom fiberglass door panels
Custom dash
Custom triple gauge pod
Alpine CDA117, 6.5" components front and rear, PDX5 and sub