Looking for R+D testers for Defined Auto promo headers

GtoRx7 · 12-26-2010, 02:53 PM

I have already found a couple people who are participating in this program, but open to more. 12a, 13b 6-port, 13b 4-port, 13b full P-port, Bridge port, ALL types will be considered to get a promotionally priced header.

The deal- Customers will purchase a Defined Autoworks prototype header that is built specifically for their engine setup/ car. Cost will be a very discounted price. If no extra power is found vs. the existing header, buyer can return for a full refund

What we need- Car must be using some type of programable ecu. so that the user has control over Air fuel, and timing. The Customer agrees to visit a dyno before and after new header install. The customer also must have knowledge of how to tune the vehicle, or has access to a tuner. Once the results are found, the user agrees to publish the results on forums.

Example header

Conclusion- And that is it! One heck of a deal, with less risk. Just post on here if you are interested. Header construction will begin in 2-3 weeks, cost will vary from $500-$600 depending on the setup. PM me for more details on your specific setup and cost.

Updated info

I should also add the following information about this program.

While originally posted as a R+D test, these headers are far from un-tested. We have been developing this technology and intake/exhaust length ratio for over 3 years now.

Proven results

Our 2 rotor street port, which is a 13b-re engine is producing 230rwhp. Using a identical approach our 3 rotor street port is over 350rwhp and the semi p-port 428rwhp.

Conclusion

So anyone interested, this is not a guinea pig test. This is a promotionally priced proven header, built to custom spec. We are excited to see the results from users running our equipment and thus promoting our name. In the off chance no extra power results, we provide a full refund. So if you are in the market for the most powerful header, consider ours.

Technical information

Material- Our headers use very expensive highest quality 321 stainless. 304 and 409 are lesser grades, and do not take rotary heat nearly as well. 321 also has better heat retention.

Tubing- The wall thickness is .060" or 1/16th. 2" o.d.

Weight- A finished header is between 12-17lbs depending on length. Each header uses a RB stainless flange.

Construction- Fully hand built and painstakingly TIG welded with back purging (nice and smooth on the inside).

Length- Primary tube length will vary between 30" and 65" depending on intake/ engine setup.

Dyno examples

PercentSevenC · 12-26-2010, 11:07 PM

That's a pretty-looking header. I almost wish I was still NA so I could help test.

GtoRx7 · 12-28-2010, 01:33 PM

Just build another n/a car

orion84gsl · 12-30-2010, 11:42 PM

So, your not carb friendly? I have a streetported 4port 13B with a completely tuneable Sterling carb on it and an RB dual exhaust. I just had the engine rebuilt and have only just had it broken in before running into issues elsewhere. I am planning to get on the dyno in the spring.

GtoRx7 · 12-31-2010, 12:51 AM

We are carb friendly, I should have added that. Adding this type of header will most likely slightly change the air/fuel ratio. So to see the strongest gain, there needs to be some type of tuning capabilities in the system. And of course carbs can do that

GtoRx7 · 12-31-2010, 01:40 AM

updated

RotorDad · 12-31-2010, 10:46 AM

Hmmm. Wouldn't mind trying a new header on my supercharged RX, but just not in my budget as of now.

GtoRx7 · 01-07-2011, 01:54 AM

Here are some pics of our hand built collector that is on each of our headers sold. This version is for a 12a, 13b is similar just slightly larger throat diameter. I think this helps convey the differences of our collectors vs. any other header available.

12-26-2010, 02:53 PM	#1
GtoRx7 Rotary Fanatic Join Date: Jul 2008 Posts: 151 Rep Power: 18	Defined Autoworks promotional header offer I have already found a couple people who are participating in this program, but open to more. 12a, 13b 6-port, 13b 4-port, 13b full P-port, Bridge port, ALL types will be considered to get a promotionally priced header. The deal- Customers will purchase a Defined Autoworks prototype header that is built specifically for their engine setup/ car. Cost will be a very discounted price. If no extra power is found vs. the existing header, buyer can return for a full refund What we need- Car must be using some type of programable ecu. so that the user has control over Air fuel, and timing. The Customer agrees to visit a dyno before and after new header install. The customer also must have knowledge of how to tune the vehicle, or has access to a tuner. Once the results are found, the user agrees to publish the results on forums. Example header Conclusion- And that is it! One heck of a deal, with less risk. Just post on here if you are interested. Header construction will begin in 2-3 weeks, cost will vary from $500-$600 depending on the setup. PM me for more details on your specific setup and cost. Updated info I should also add the following information about this program. While originally posted as a R+D test, these headers are far from un-tested. We have been developing this technology and intake/exhaust length ratio for over 3 years now. Proven results Our 2 rotor street port, which is a 13b-re engine is producing 230rwhp. Using a identical approach our 3 rotor street port is over 350rwhp and the semi p-port 428rwhp. Conclusion So anyone interested, this is not a guinea pig test. This is a promotionally priced proven header, built to custom spec. We are excited to see the results from users running our equipment and thus promoting our name. In the off chance no extra power results, we provide a full refund. So if you are in the market for the most powerful header, consider ours. Technical information Material- Our headers use very expensive highest quality 321 stainless. 304 and 409 are lesser grades, and do not take rotary heat nearly as well. 321 also has better heat retention. Tubing- The wall thickness is .060" or 1/16th. 2" o.d. Weight- A finished header is between 12-17lbs depending on length. Each header uses a RB stainless flange. Construction- Fully hand built and painstakingly TIG welded with back purging (nice and smooth on the inside). Length- Primary tube length will vary between 30" and 65" depending on intake/ engine setup. Dyno examples __________________ DEFINED AUTOWORKS Where concept meets results Black 1994 FD 4-rotor 610rwhp all motor Red 1970 Mazda R-100 with 10a Black 1974 Mazda Rx4 Black 1984 Gsl-SE 13b-re streetport 230rwhp Last edited by GtoRx7; 12-31-2010 at 01:54 AM. Reason: incorrect choice of wording on initial post

12-28-2010, 01:33 PM	#3
GtoRx7 Rotary Fanatic Join Date: Jul 2008 Posts: 151 Rep Power: 18	Just build another n/a car __________________ DEFINED AUTOWORKS Where concept meets results Black 1994 FD 4-rotor 610rwhp all motor Red 1970 Mazda R-100 with 10a Black 1974 Mazda Rx4 Black 1984 Gsl-SE 13b-re streetport 230rwhp

12-31-2010, 12:51 AM	#5
GtoRx7 Rotary Fanatic Join Date: Jul 2008 Posts: 151 Rep Power: 18	We are carb friendly, I should have added that. Adding this type of header will most likely slightly change the air/fuel ratio. So to see the strongest gain, there needs to be some type of tuning capabilities in the system. And of course carbs can do that __________________ DEFINED AUTOWORKS Where concept meets results Black 1994 FD 4-rotor 610rwhp all motor Red 1970 Mazda R-100 with 10a Black 1974 Mazda Rx4 Black 1984 Gsl-SE 13b-re streetport 230rwhp

12-31-2010, 01:40 AM	#6
GtoRx7 Rotary Fanatic Join Date: Jul 2008 Posts: 151 Rep Power: 18	updated __________________ DEFINED AUTOWORKS Where concept meets results Black 1994 FD 4-rotor 610rwhp all motor Red 1970 Mazda R-100 with 10a Black 1974 Mazda Rx4 Black 1984 Gsl-SE 13b-re streetport 230rwhp Last edited by GtoRx7; 12-31-2010 at 01:52 AM.

12-31-2010, 10:46 AM	#7
RotorDad Big Ugly Join Date: Apr 2009 Location: Fredericksburg, Va Posts: 591 Rep Power: 17	Hmmm. Wouldn't mind trying a new header on my supercharged RX, but just not in my budget as of now. __________________ *Boosted Big Body On 335's* PS3 ID: Rotordad 1986 Mazda RX7 GXL - Street ported 13BT, Haltech, 62mm, ect. 2006 MazdaSpeed 6 - Eagle, Wiseco, Cobb, ect.

12-30-2010, 11:42 PM	#4
orion84gsl Rotary Fanatic Join Date: Mar 2008 Posts: 167 Rep Power: 18	So, your not carb friendly? I have a streetported 4port 13B with a completely tuneable Sterling carb on it and an RB dual exhaust. I just had the engine rebuilt and have only just had it broken in before running into issues elsewhere. I am planning to get on the dyno in the spring.

01-07-2011, 01:54 AM	#8
GtoRx7 Rotary Fanatic Join Date: Jul 2008 Posts: 151 Rep Power: 18	Here are some pics of our hand built collector that is on each of our headers sold. This version is for a 12a, 13b is similar just slightly larger throat diameter. I think this helps convey the differences of our collectors vs. any other header available. __________________ DEFINED AUTOWORKS Where concept meets results Black 1994 FD 4-rotor 610rwhp all motor Red 1970 Mazda R-100 with 10a Black 1974 Mazda Rx4 Black 1984 Gsl-SE 13b-re streetport 230rwhp

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode