Bit of an emergency question here...

sv51macross · 11-25-2010, 07:00 PM

The more I delve, the more I find out. So, in the hopes of gaining some access to the LIM bolts, I remove the airpump. I read the shop manual procedure, and go out. Now, I'm wondering why the heck can I not find the adjustment bracket. Then it hits me:

THERE IS NO adjustment bracket! So all this time, the support bolt/hinge has been keeping tension (or not) against the air pump belt.

NEVER buy a FC for $1000 off eBay.

So in all seriousness, before I loose my mind, anyone have nay tips for getting at the bottom two and rear two bolts on the LIM?

Mazdabater · 11-25-2010, 10:38 PM

Handskills? Did you try the vacum cleaner idea of mine? I got a part of a zip tie out of mine by that.

sv51macross · 11-25-2010, 11:22 PM

Don't have the right materials for a hose on hand. Plus, I've already invested so much effort into removing the LIM that I'm following through with it if it kills me. As an enthusiast, I must not be defeated by this, I must persevere!

Pete_89T2 · 11-25-2010, 11:24 PM

Quote:

Originally Posted by Mazdabater

Handskills? Did you try the vacum cleaner idea of mine? I got a part of a zip tie out of mine by that.

+1... I suggested a shop vac many posts ago as well. I can vouch for the fact it works - saved my a$$ in a similar situation - dropped one of the fuel rail bolts in the LIM once and the shop vac sucked it right up.

sv51macross · 11-26-2010, 11:31 AM

I got it out! I had to remove both 5/6 port actuators and then the LIM but I got it out!

Very lucky I was. The runner had 'chuted' the washer so it traveled at the port horizontally. The port necked down enough that the washer wedged horizontally in the port, so it never actually entered the block.

Whew!

So now I just have to reassemble the lower intake tract, finish replacing the oil injection lines, pressure test the fuel system, and reassemble the whole shebang.

Peace, and thanks for the support!

FerociousP · 11-29-2010, 10:18 AM

Do it to it Lars! congrats on NOT doing something that we've all had that little adrenaline shot thinking about if it happened to us...

11-25-2010, 07:00 PM	#16
sv51macross Rotary Fan in Training Join Date: Oct 2010 Location: Ann Arbor, Mi iTrader: (0) Posts: 47 Rep Power: 0	The more I delve, the more I find out. So, in the hopes of gaining some access to the LIM bolts, I remove the airpump. I read the shop manual procedure, and go out. Now, I'm wondering why the heck can I not find the adjustment bracket. Then it hits me: THERE IS NO adjustment bracket! So all this time, the support bolt/hinge has been keeping tension (or not) against the air pump belt. NEVER buy a FC for $1000 off eBay. So in all seriousness, before I loose my mind, anyone have nay tips for getting at the bottom two and rear two bolts on the LIM? __________________ 1990 Mazda RX-7 NA; Lucy, after the main antagonist from Elfin Lied. Eventual plans? Something cyberpunk and spicy.

11-25-2010, 11:22 PM	#18
sv51macross Rotary Fan in Training Join Date: Oct 2010 Location: Ann Arbor, Mi iTrader: (0) Posts: 47 Rep Power: 0	Don't have the right materials for a hose on hand. Plus, I've already invested so much effort into removing the LIM that I'm following through with it if it kills me. As an enthusiast, I must not be defeated by this, I must persevere! __________________ 1990 Mazda RX-7 NA; Lucy, after the main antagonist from Elfin Lied. Eventual plans? Something cyberpunk and spicy.

11-26-2010, 11:31 AM	#20
sv51macross Rotary Fan in Training Join Date: Oct 2010 Location: Ann Arbor, Mi iTrader: (0) Posts: 47 Rep Power: 0	I got it out! I had to remove both 5/6 port actuators and then the LIM but I got it out! Very lucky I was. The runner had 'chuted' the washer so it traveled at the port horizontally. The port necked down enough that the washer wedged horizontally in the port, so it never actually entered the block. Whew! So now I just have to reassemble the lower intake tract, finish replacing the oil injection lines, pressure test the fuel system, and reassemble the whole shebang. Peace, and thanks for the support! __________________ 1990 Mazda RX-7 NA; Lucy, after the main antagonist from Elfin Lied. Eventual plans? Something cyberpunk and spicy.

11-29-2010, 10:18 AM	#21
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	Do it to it Lars! congrats on NOT doing something that we've all had that little adrenaline shot thinking about if it happened to us... __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-25-2010, 10:38 PM	#17
Mazdabater FC3S Join Date: Jun 2010 Location: Townsville, QLD, AUS iTrader: (0) Posts: 326 Rep Power: 15	Handskills? Did you try the vacum cleaner idea of mine? I got a part of a zip tie out of mine by that.