New project: 1976 Cosmo RX-5

rx7 vinnie · 04-03-2015, 07:26 PM

I'll bleed soy sauce.....

djmtsu · 04-04-2015, 09:36 AM

Quote:

Originally Posted by rx7 vinnie

I'll bleed soy sauce.....

I like soy sauce.

djmtsu · 08-11-2015, 07:52 AM

Here's a dumb update, since it has been like 4 months.

I bought a 1992 Miata roller. Did some measuring. And now I'm going to attempt an IRS swap from the Miata onto the Cosmo.

Pray for me.

t_g_farrell · 08-11-2015, 10:07 AM

WAHT! Sounds insane, do it and I'll watch.

GySgtFrank · 08-11-2015, 10:34 AM

Quote:

Originally Posted by t_g_farrell

WAHT! Sounds insane, do it and I'll watch.

Good. You can hold his beer.

FC Zach · 08-11-2015, 10:56 PM

djmtsu · 08-13-2015, 08:52 AM

It all seems like it might work. Same width between the rails for the front subframe, rack, suspension arms, sway bar is all contained as a unit. Only serious modification would be to lower the shock towers. For the rear, there is tons of room back there. The fuel tank is in the trunk, and there is nothing else back there. The rear is also a self contained unit. Nothing except the strut tops is 'outside' the assembly.

GySgtFrank · 08-13-2015, 10:56 AM

Go for it. Sounds like a definite improvement to the solid axle and you won't have to worry about breaking it with a rotary.

djmtsu · 08-13-2015, 04:36 PM

Improvement all around! No more solid axle. Vastly superior suspension. Brake parts the are stupid easy to source and upgrade. Bolt pattern unleashes an infinite wheel choice. No need for a 2 piece driveshaft. Rack and Pinion steering. Do I need to go on??

FC Zach · 08-13-2015, 11:19 PM

This is awesome man, cant wait to see progress! Hell, I can't wait to see it on the road!!

djmtsu · 10-27-2015, 11:34 AM

Fuel tank is cleaned up, should be good now. All that is really left is to find the new battery cables I bought (or just get more), get a battery and fire it up.

Had to get a new heater hose (the elbow off the rear iron) since the one that was on it disintegrated as soon as coolant flowed into it. Looks like there is an oil leak in the oil cooler area. Don't know if it is just a connection issue (I have new crush washers) or if the cooler is cracked. If it is, I'll steal the one off white Cosmo for now.

Once it is fired up and running, I will need to figure out if it is the brake switch or wiring keeping the brake lights from functioning. Then, figure out the washer pump, and horn. All these are simple and can be rewire in short time, so I'm not concerned. I do need to find a gauge solution for coolant and oil pressure. Not sure where to put them.

DGRR 2016 here we come. Ugly.

GySgtFrank · 10-27-2015, 01:10 PM

Quote:

Originally Posted by djmtsu

DGRR 2016 here we come. Ugly.

I do believe we heard this last year, you little tease you.

djmtsu · 10-27-2015, 01:59 PM

Quote:

Originally Posted by GySgtFrank

I do believe we heard this last year, you little tease you.

Glass houses Gunny....

FC Zach · 10-27-2015, 10:50 PM

Quote:

Originally Posted by GySgtFrank

I do believe we heard this last year, you little tease you.

It did take him two years to clean a gas tank

djmtsu · 10-28-2015, 09:44 AM

Quote:

Originally Posted by FC Zach

It did take him two years to clean a gas tank

One year.....and if it you think it is easy, I'll give you the other tank to clean.....

04-03-2015, 07:26 PM	#271
rx7 vinnie I SEE DEAD PEOPLE Join Date: Mar 2008 Location: nashville, tn (antioch) iTrader: (0) Posts: 743 Rep Power: 17	I'll bleed soy sauce..... __________________ VIN-AUTO Rotary list of Fails below: 86 mazda rx7 csp 61 N/A= because RACECAR 87 mazda rx7 t2 with 13b-re cosmo GT42= FKN RUNS!!! 03 Dodge Viper SRT-10 Vert 06 dodge ram 2500 Megacab turbo Cummins=puller 16 MB ML350

08-11-2015, 07:52 AM	#273
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Here's a dumb update, since it has been like 4 months. I bought a 1992 Miata roller. Did some measuring. And now I'm going to attempt an IRS swap from the Miata onto the Cosmo. Pray for me. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

08-11-2015, 10:07 AM	#274
t_g_farrell Waffles - hmmm good Join Date: Aug 2008 Location: Huntersville, NC iTrader: (0) Posts: 757 Rep Power: 0	WAHT! Sounds insane, do it and I'll watch. __________________ 1980 GS stockport, Fat Nikki, RB Dual Facetfuel pumps, Holley regulator, RB Street port exhaust, 2GDFIS, MR2 MK I electric fans, 2G strut bar, relayed fans, lights and fuel pump, LEDs Project Fat Nikki Budget 12A rebuild Video setup < $30.00

08-11-2015, 10:56 PM	#276
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN iTrader: (2) Posts: 2,267 Rep Power: 19	__________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

08-13-2015, 08:52 AM	#277
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	It all seems like it might work. Same width between the rails for the front subframe, rack, suspension arms, sway bar is all contained as a unit. Only serious modification would be to lower the shock towers. For the rear, there is tons of room back there. The fuel tank is in the trunk, and there is nothing else back there. The rear is also a self contained unit. Nothing except the strut tops is 'outside' the assembly. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

08-13-2015, 10:56 AM	#278
GySgtFrank Professional Stick Poker Join Date: Feb 2011 Location: Stafford, Ks. iTrader: (0) Posts: 1,005 Rep Power: 15	Go for it. Sounds like a definite improvement to the solid axle and you won't have to worry about breaking it with a rotary. __________________ 1979 SA22C (parts of one anyway) http://rotarycarclub.com/rotary_foru...ad.php?t=15585 1975 MG Midget (building) http://rotarycarclub.com/rotary_foru...ad.php?t=18681 1988 N/A SE model FC, dead stock and less than 85k on the clock. This one actually runs, so I don't fuck with it.

08-13-2015, 04:36 PM	#279
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Improvement all around! No more solid axle. Vastly superior suspension. Brake parts the are stupid easy to source and upgrade. Bolt pattern unleashes an infinite wheel choice. No need for a 2 piece driveshaft. Rack and Pinion steering. Do I need to go on?? __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

08-13-2015, 11:19 PM	#280
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN iTrader: (2) Posts: 2,267 Rep Power: 19	This is awesome man, cant wait to see progress! Hell, I can't wait to see it on the road!! __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

10-27-2015, 11:34 AM	#281
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Fuel tank is cleaned up, should be good now. All that is really left is to find the new battery cables I bought (or just get more), get a battery and fire it up. Had to get a new heater hose (the elbow off the rear iron) since the one that was on it disintegrated as soon as coolant flowed into it. Looks like there is an oil leak in the oil cooler area. Don't know if it is just a connection issue (I have new crush washers) or if the cooler is cracked. If it is, I'll steal the one off white Cosmo for now. Once it is fired up and running, I will need to figure out if it is the brake switch or wiring keeping the brake lights from functioning. Then, figure out the washer pump, and horn. All these are simple and can be rewire in short time, so I'm not concerned. I do need to find a gauge solution for coolant and oil pressure. Not sure where to put them. DGRR 2016 here we come. Ugly. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode