Flywheel and EShaft Pulley N&B

BLKTOPTRVL · 05-06-2008, 10:07 AM

I know this has been discussed on the other forum, but I also think we need to build up information here. Besides, I like telling my stories. So...

I could not get the Pulley Bolt, or the flywheel nut to budge.

So, As Ted and others suggested, I decided to set up my compressor (for the first time) and zip those suckers off fast and quick.

Setting up the compressor (8.6scfm @40 PSI, 6.4scfm @90 PSI, 150PSI max, 33 Gal Tank, 2HP running) was cake. My impact is only rated at 300 Ft Lbs. (Got the whole rig at Sears on sale for about $300)

Tried to remove the nut and bolt using the compressor. Zip. Nada. Wouldn't budge.

So, remembering some information gathered a long time ago, I applied heat around the Flywheel nut using a propane torch for about 3-4 minutes (too long?). Came right off.

The front pulley bolt was more stubborn, but after an additional three minutes or so, it also came off. I am guessing none.

I just wonder how much damage (if any) all that heat could have done.

tom93r1 · 05-06-2008, 12:13 PM

You are good. The thing to worry about is the possibility of cooking the front and rear main seals but you should be replacing them any way.

BLKTOPTRVL · 05-06-2008, 12:27 PM

Definitely replacing them, funny, the thing smoked for about 15 minutes after. Now I am off to go get a flywheel puller.

BLKTOPTRVL · 05-06-2008, 06:09 PM

Once again I went back to the old stories told...

Use a prybar and a soft mallet to remove the wheel. No dice.

Then I found RotaryReserection's write up on the subject...

http://www.rotaryresurrection.com/2n...el_remove.html

Two slight blows to the FW and it was off.

Thanks RR. I think his site should be compulsary reading.

misterstyx69 · 10-28-2008, 04:51 PM

..just piss off your Sister and give her a hammer!..the parts fly off!..but seriously,I had my engine strapped on a pallet and I used a piece of chain on the Flywheel and attached it to a pressure plate bolt and the bolt that Holds the Trans to the Engine.With a 3 and 1/2 foot 3/4 drive breaker bar I got the 54mm Flywheel nut off.then while the Flywheel nut was Just Cracked(still on),I moved the assembly to tighten the other way,so I could get at the 19mm front pulley Nut.I put it on and had a Buddy steady it while I jumped on the Bar.It came right off..My total for a breaker bar and the Flywheel socket was 26 dollars CDN.(already had the 19mm Socket!.lol!)

Barry Bordes · 10-31-2008, 06:59 AM

Or you can make a special tool from an old pressure plate assembly.
Barry

Signal 2 · 11-07-2008, 06:29 AM

^Some powdercoat and your ready to start a group buy.

This has been the best $90 I ever spent considering the trouble it's saved. http://www.harborfreight.com/cpi/cta...temnumber=2623

05-06-2008, 10:07 AM	#1
BLKTOPTRVL Rotary Fanatic Join Date: Feb 2008 iTrader: (0) Posts: 192 Rep Power: 17	Flywheel and EShaft Pulley N&B I know this has been discussed on the other forum, but I also think we need to build up information here. Besides, I like telling my stories. So... I could not get the Pulley Bolt, or the flywheel nut to budge. So, As Ted and others suggested, I decided to set up my compressor (for the first time) and zip those suckers off fast and quick. Setting up the compressor (8.6scfm @40 PSI, 6.4scfm @90 PSI, 150PSI max, 33 Gal Tank, 2HP running) was cake. My impact is only rated at 300 Ft Lbs. (Got the whole rig at Sears on sale for about $300) Tried to remove the nut and bolt using the compressor. Zip. Nada. Wouldn't budge. So, remembering some information gathered a long time ago, I applied heat around the Flywheel nut using a propane torch for about 3-4 minutes (too long?). Came right off. The front pulley bolt was more stubborn, but after an additional three minutes or so, it also came off. I am guessing none. I just wonder how much damage (if any) all that heat could have done. __________________ ...shoot a mother-humpin moose, eight days of the week... Last edited by BLKTOPTRVL; 05-06-2008 at 10:09 AM..

05-06-2008, 12:27 PM	#3
BLKTOPTRVL Rotary Fanatic Join Date: Feb 2008 iTrader: (0) Posts: 192 Rep Power: 17	Definitely replacing them, funny, the thing smoked for about 15 minutes after. Now I am off to go get a flywheel puller. __________________ ...shoot a mother-humpin moose, eight days of the week... Last edited by BLKTOPTRVL; 05-06-2008 at 04:53 PM..

05-06-2008, 06:09 PM	#4
BLKTOPTRVL Rotary Fanatic Join Date: Feb 2008 iTrader: (0) Posts: 192 Rep Power: 17	Getting the Flywheel off. Once again I went back to the old stories told... Use a prybar and a soft mallet to remove the wheel. No dice. Then I found RotaryReserection's write up on the subject... http://www.rotaryresurrection.com/2n...el_remove.html Two slight blows to the FW and it was off. Thanks RR. I think his site should be compulsary reading. __________________ ...shoot a mother-humpin moose, eight days of the week...

10-31-2008, 06:59 AM	#6
Barry Bordes Rotary Fanatic Join Date: Feb 2008 Location: Slidell, LA iTrader: (0) Posts: 191 Rep Power: 17	Or you can make a special tool from an old pressure plate assembly. Barry __________________ GOD the Incomprehensible Obvious (www.frksj.org)

11-07-2008, 06:29 AM	#7
Signal 2 Viable Fossil Join Date: Mar 2008 Location: Mid-West iTrader: (0) Posts: 199 Rep Power: 17	^Some powdercoat and your ready to start a group buy. This has been the best $90 I ever spent considering the trouble it's saved. http://www.harborfreight.com/cpi/cta...temnumber=2623 __________________ Jim VR R1 FD

05-06-2008, 12:13 PM	#2
tom93r1 Rotary Fan in Training Join Date: Feb 2008 iTrader: (0) Posts: 45 Rep Power: 0	You are good. The thing to worry about is the possibility of cooking the front and rear main seals but you should be replacing them any way.

10-28-2008, 04:51 PM	#5
misterstyx69 .drives like MrMagoo! Join Date: Feb 2008 Location: Smiths Falls,Ontario iTrader: (5) Posts: 198 Rep Power: 17	..just piss off your Sister and give her a hammer!..the parts fly off!..but seriously,I had my engine strapped on a pallet and I used a piece of chain on the Flywheel and attached it to a pressure plate bolt and the bolt that Holds the Trans to the Engine.With a 3 and 1/2 foot 3/4 drive breaker bar I got the 54mm Flywheel nut off.then while the Flywheel nut was Just Cracked(still on),I moved the assembly to tighten the other way,so I could get at the 19mm front pulley Nut.I put it on and had a Buddy steady it while I jumped on the Bar.It came right off..My total for a breaker bar and the Flywheel socket was 26 dollars CDN.(already had the 19mm Socket!.lol!)

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode