20B Eshaft Pullers -Pics-

***Herblenny*** · 05-06-2008, 08:43 AM

I thought I post it here..

Here are what 20B Eshaft Pullers look like..

Home Made Puller

***Herblenny*** · 05-06-2008, 08:45 AM

Mazda Special Tool!

Inside

BLK FC3S · 05-06-2008, 09:40 AM

NICE! I might have to borrow that from you one day.

tom93r1 · 05-06-2008, 12:15 PM

very creative! And alot less $$ than the Mazda tool.

To_Slow · 05-08-2008, 08:00 PM

Quote:

Originally Posted by Herblenny

Mazda Special Tool!

Inside

That looks like Carlos Lopez e-shaft puller. Nice pice. Well worth the money.

AHarada · 05-08-2008, 08:31 PM

Nice work.

What exactly is this used for?

HellBent · 05-09-2008, 03:16 AM

PULLING OUT THE ECCENTRIC would be my guess, since its a ECCENTRIC SHAFT PULLER

jtbshaw · 05-20-2008, 05:11 PM

Quote:

Originally Posted by RotaryResurrection

< butthead> uh huh huh, he said "shaft puller", huh huh huh < /butthead>

that's funny!

Prometheus · 09-03-2008, 07:35 PM

Jesus, I wish I had one of those a last weekend.

I had to use a pry bar (that I wrapped with a rag many times, to be sure not to gnar the lobe) and a piece of Teflon between the side plate (to crush/ cushion) tha back side of the pry bar.

with some penetrating oil and no tapping with a hammer, the lobe simply slid off with adequate pressure applied to the pry bar.

I was surprised on how easy the lobe came off.

I did this on 3 20B blocks and there was no damage.

05-09-2008, 03:16 AM	#7
HellBent Evil and Proud Join Date: Feb 2008 Location: Maryville TN, 10 mins from the DRAGON iTrader: (0) Posts: 81 Rep Power: 17	PULLING OUT THE ECCENTRIC would be my guess, since its a ECCENTRIC SHAFT PULLER __________________ going to die young and leave a good looking corpse and a mangled seven

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

05-06-2008, 09:40 AM	#3
BLK FC3S C088 Join Date: Mar 2008 Location: Mount Dora, FL (no its not a mountian) iTrader: (0) Posts: 112 Rep Power: 17	NICE! I might have to borrow that from you one day.

05-06-2008, 12:15 PM	#4
tom93r1 Rotary Fan in Training Join Date: Feb 2008 iTrader: (0) Posts: 45 Rep Power: 0	very creative! And alot less $$ than the Mazda tool.

05-08-2008, 08:31 PM	#6
AHarada Rotary Fanatic Join Date: Mar 2008 iTrader: (1) Posts: 162 Rep Power: 17	Nice work. What exactly is this used for?

09-03-2008, 07:35 PM	#9
Prometheus Rotary Fan in Training Join Date: Feb 2008 Location: Portland, Oregon/ Vancouver, Washington Area iTrader: (0) Posts: 49 Rep Power: 0	Jesus, I wish I had one of those a last weekend. I had to use a pry bar (that I wrapped with a rag many times, to be sure not to gnar the lobe) and a piece of Teflon between the side plate (to crush/ cushion) tha back side of the pry bar. with some penetrating oil and no tapping with a hammer, the lobe simply slid off with adequate pressure applied to the pry bar. I was surprised on how easy the lobe came off. I did this on 3 20B blocks and there was no damage.