Alternator question, battery is discharging quickly.

***TitaniumTT*** · 03-03-2017, 09:46 AM

Ok, so I went to go take a look at the resistors that I set up.... I did a little heatshrinking over the resistors so I couldn't identify them that way, I should've just ohmed them out, I'll try that tomorrow when I'm back at the shop, in the meatime, Ohms law tells me to start with the 150ohm resistor that you have and measure the voltage at the corresponding pins as per the FSM. There should be 1.2v drop across them

FC Zach · 03-06-2017, 03:58 AM

I swapped my trans/clutch this weekend and since the power harness was mostly disconnected I went ahead and removed it completely. . thing is haggard to say the least. It wasn't hard for me to pull the loom apart to expose wires since the electrical tape was rotted and crumbled away. The OE alt. wires for the "T" shaped connector were nowhere to be found. .

With this said, I emailed Chris Ludwig asking if this harness is something he can make. . If not, does anyone have any recommendations on where to get this harness or have one made?

03-03-2017, 09:46 AM	#1
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son Posts: 4,581 Rep Power: 10	Ok, so I went to go take a look at the resistors that I set up.... I did a little heatshrinking over the resistors so I couldn't identify them that way, I should've just ohmed them out, I'll try that tomorrow when I'm back at the shop, in the meatime, Ohms law tells me to start with the 150ohm resistor that you have and measure the voltage at the corresponding pins as per the FSM. There should be 1.2v drop across them __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-06-2017, 03:58 AM	#2
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN Posts: 2,267 Rep Power: 20	I swapped my trans/clutch this weekend and since the power harness was mostly disconnected I went ahead and removed it completely. . thing is haggard to say the least. It wasn't hard for me to pull the loom apart to expose wires since the electrical tape was rotted and crumbled away. The OE alt. wires for the "T" shaped connector were nowhere to be found. . With this said, I emailed Chris Ludwig asking if this harness is something he can make. . If not, does anyone have any recommendations on where to get this harness or have one made? __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode