The Great Evinrude Adventure!

Buggy · 03-14-2013, 06:55 AM

Quote:

Originally Posted by tweiss3

That is an awesome find. And the fact that you are getting some great use out of it is even better.

I believe that just owning something to look at it is pointless. If I can't play with it and use it why have it!

Buggy · 12-14-2013, 11:13 AM

Time to bring this thread back to life! I basically had no time this summer to work on anything, but now that the snow is here it's time to get back at the envinrude. I got it all back together yet last winter after I broke the drive sprockets and used it a bit more. I still had problems with it wanting to die on me though once it got warm. I pulled the engine out of it just last week and tore it down to the bare keg and checked it for vacuum leaks. The only thing I found was the carb is leaking pretty bad around the throttle shafts. I did reseal a few things and tightened up the through bolts on the engine just to be sure before I put it all back together. I put fresh fuel in it and charged the battery. It fired right up and ran like a champ! For about 5 minutes... It runs for a bit perfectly and then just like you turned off the key it dies and won't even attempt to restart. I'm thinking it's an ignition issue and hope I have time soon to look at it. Could also be low on compression so I may have to make an adaptor for the 12mm spark plug hole and test it. I also know of another one for sale locally that I may go pick up. Can never have too many parts lol!

Buggy · 12-21-2013, 06:54 PM

I went out and worked on the sled again. I fired it up with my spark tester hooked up and ran it until it died. I still had spark and lots of fuel supply so that only left one thing, compression! I wasted no time collecting all of my spare engine parts and I removed the engine from the sled again. I took the engine apart and found 2 corner seals were broken, the side plate was badly worn from the broken corner seals, and the housing had a nasty chunk out of the inside by the spark plug. No wonder it ran like crap! Luckily I had spare parts to replace all of those things so I did a quick rebuild. I also drilled the spark plug hole out to accept a 14mm spark plug instead of the obsolete 12mm stock plugs. I then put it all back together and tried it again. It ran much better than before, but still not 100%. It wouldn't idle for me and it wanted to cut out randomly on me. I decided to rebuild my other spare carburetor. The spare carb was pretty ugly so I figured it would be pretty untouched and original compared to my other carb. After some cleaning and a good soak in cleaner it was good to go! I put that carb on today and finally it runs good! Idles away very nice, just needs some fine tuning and a better battery.
rc1.jpg rc2.jpg rc3.jpg rc4.jpg rc5.jpg

Buggy · 12-21-2013, 06:54 PM

rc6.jpg rc7.jpg

casual_john · 12-27-2013, 07:53 PM

Congrats! I bet you are one of very few who have rebuilt a rotary snowmobile.

12-14-2013, 11:13 AM	#17
Buggy I've been Wankeled! Join Date: Apr 2010 Location: Mildmay, Ontario, Canada iTrader: (0) Posts: 260 Rep Power: 15	Time to bring this thread back to life! I basically had no time this summer to work on anything, but now that the snow is here it's time to get back at the envinrude. I got it all back together yet last winter after I broke the drive sprockets and used it a bit more. I still had problems with it wanting to die on me though once it got warm. I pulled the engine out of it just last week and tore it down to the bare keg and checked it for vacuum leaks. The only thing I found was the carb is leaking pretty bad around the throttle shafts. I did reseal a few things and tightened up the through bolts on the engine just to be sure before I put it all back together. I put fresh fuel in it and charged the battery. It fired right up and ran like a champ! For about 5 minutes... It runs for a bit perfectly and then just like you turned off the key it dies and won't even attempt to restart. I'm thinking it's an ignition issue and hope I have time soon to look at it. Could also be low on compression so I may have to make an adaptor for the 12mm spark plug hole and test it. I also know of another one for sale locally that I may go pick up. Can never have too many parts lol! __________________ 1976 Rx-4 hardtop. Half bridge 3B 13B, S5 NA rotors, Renesis e-shaft, stat gears, and bearings, balanced rotating assembly, RE dual weber 36 DCD's 203rwhp 137ft-lbs torque DGRR 2011 3rd place 1974 Rx-4 all original 27,000 miles 1988 Rx-7 TII 320rwhp. DGRR 2012 3rd place

12-21-2013, 06:54 PM	#18
Buggy I've been Wankeled! Join Date: Apr 2010 Location: Mildmay, Ontario, Canada iTrader: (0) Posts: 260 Rep Power: 15	I went out and worked on the sled again. I fired it up with my spark tester hooked up and ran it until it died. I still had spark and lots of fuel supply so that only left one thing, compression! I wasted no time collecting all of my spare engine parts and I removed the engine from the sled again. I took the engine apart and found 2 corner seals were broken, the side plate was badly worn from the broken corner seals, and the housing had a nasty chunk out of the inside by the spark plug. No wonder it ran like crap! Luckily I had spare parts to replace all of those things so I did a quick rebuild. I also drilled the spark plug hole out to accept a 14mm spark plug instead of the obsolete 12mm stock plugs. I then put it all back together and tried it again. It ran much better than before, but still not 100%. It wouldn't idle for me and it wanted to cut out randomly on me. I decided to rebuild my other spare carburetor. The spare carb was pretty ugly so I figured it would be pretty untouched and original compared to my other carb. After some cleaning and a good soak in cleaner it was good to go! I put that carb on today and finally it runs good! Idles away very nice, just needs some fine tuning and a better battery. rc1.jpg rc2.jpg rc3.jpg rc4.jpg rc5.jpg __________________ 1976 Rx-4 hardtop. Half bridge 3B 13B, S5 NA rotors, Renesis e-shaft, stat gears, and bearings, balanced rotating assembly, RE dual weber 36 DCD's 203rwhp 137ft-lbs torque DGRR 2011 3rd place 1974 Rx-4 all original 27,000 miles 1988 Rx-7 TII 320rwhp. DGRR 2012 3rd place

12-21-2013, 06:54 PM	#19
Buggy I've been Wankeled! Join Date: Apr 2010 Location: Mildmay, Ontario, Canada iTrader: (0) Posts: 260 Rep Power: 15	rc6.jpg rc7.jpg __________________ 1976 Rx-4 hardtop. Half bridge 3B 13B, S5 NA rotors, Renesis e-shaft, stat gears, and bearings, balanced rotating assembly, RE dual weber 36 DCD's 203rwhp 137ft-lbs torque DGRR 2011 3rd place 1974 Rx-4 all original 27,000 miles 1988 Rx-7 TII 320rwhp. DGRR 2012 3rd place

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-27-2013, 07:53 PM	#20
casual_john Dover White GXL Join Date: Mar 2013 Location: London, Ontario iTrader: (0) Posts: 9 Rep Power: 0	Congrats! I bet you are one of very few who have rebuilt a rotary snowmobile.