All motor 12a rebuild.

Tri-Angles · 07-15-2011, 02:10 AM

Hey guys, I have a 82' rx7 with a 12a that ive been j porting here lately. I wanted to know If I had my stock nikki carb jetted and raised my fuel pressure a bit would I be able to use my nikki to run it daily until I got a holley/weber carb. I don't push my car hard at all so im not concerned with having a heavy foot. Any really good and sound advice would be helpful. Thanks

Whizbang · 07-15-2011, 08:55 AM

technically speaking it can work and you seem aware that it wouldn't see its full potential. I have a good deal on a weber 48 ida from my streetport 12a. Thing ran damn good! Lots of spare jets with it if you choose to bypass the work and cost of rejetting the niki

j9fd3s · 07-15-2011, 01:50 PM

i have a buddy who has run F prepared (i think) for a couple of decades, its a small bridgeport 12A or 13B and a modded nikki. i think it works because the bridge is on the small side, and its moderate timing.

the carb mods are really similar to what sterling, or paul yaw or rotary engineering were doing. although mike, my buddy prefers to use the older pre rx7 nikki's and manifold.

weber or holley would probably be more HP, but the nikki will work too

Tri-Angles · 07-16-2011, 03:13 AM

Quote:

Originally Posted by Gravity Fed

technically speaking it can work and you seem aware that it wouldn't see its full potential. I have a good deal on a weber 48 ida from my streetport 12a. Thing ran damn good! Lots of spare jets with it if you choose to bypass the work and cost of rejetting the niki

Ok. How much would you sell it for if you were to sell it? And if not what size jets could I use on my nikki to make this work. Im making my order for my gasket kit tomorrow or sunday but i wont be able to get my rotor kit until maybe 2 weeks from now. My biggest thing would be getting my intake and carb because im on a tight budget because im starting UTI in sept. :-/

Tri-Angles · 07-16-2011, 03:17 AM

And here is the link to ausrotary where i have a few pics of the j port that i did on my plates. I havent finished my intake ports yet. Im not going to go too high on my centre plates intake ports though. http://www.ausrotary.com/viewtopic.p...3584&start=100

-xlr8planet- · 07-25-2011, 04:47 PM

I really like the overall shape of the ports

07-15-2011, 02:10 AM	#1
Tri-Angles The Newbie Join Date: Dec 2010 iTrader: (0) Posts: 8 Rep Power: 0	All motor 12a rebuild. Hey guys, I have a 82' rx7 with a 12a that ive been j porting here lately. I wanted to know If I had my stock nikki carb jetted and raised my fuel pressure a bit would I be able to use my nikki to run it daily until I got a holley/weber carb. I don't push my car hard at all so im not concerned with having a heavy foot. Any really good and sound advice would be helpful. Thanks

07-15-2011, 08:55 AM	#2
Whizbang Respecognize! Join Date: Jul 2008 Location: Δx = ħ/2Δp iTrader: (5) Posts: 3,190 Rep Power: 20	technically speaking it can work and you seem aware that it wouldn't see its full potential. I have a good deal on a weber 48 ida from my streetport 12a. Thing ran damn good! Lots of spare jets with it if you choose to bypass the work and cost of rejetting the niki __________________ For current updates and event coverage check out Follow on Twitter! @WhizbangRally Whizbang Rally's Webpage \| Facebook

07-15-2011, 01:50 PM	#3
j9fd3s Rotary Fanatic Join Date: Mar 2008 iTrader: (0) Posts: 123 Rep Power: 17	i have a buddy who has run F prepared (i think) for a couple of decades, its a small bridgeport 12A or 13B and a modded nikki. i think it works because the bridge is on the small side, and its moderate timing. the carb mods are really similar to what sterling, or paul yaw or rotary engineering were doing. although mike, my buddy prefers to use the older pre rx7 nikki's and manifold. weber or holley would probably be more HP, but the nikki will work too Last edited by j9fd3s; 07-15-2011 at 01:55 PM..

07-16-2011, 03:17 AM	#5
Tri-Angles The Newbie Join Date: Dec 2010 iTrader: (0) Posts: 8 Rep Power: 0	And here is the link to ausrotary where i have a few pics of the j port that i did on my plates. I havent finished my intake ports yet. Im not going to go too high on my centre plates intake ports though. http://www.ausrotary.com/viewtopic.p...3584&start=100 Last edited by Tri-Angles; 07-16-2011 at 09:58 PM.. Reason: Forgot the link

07-25-2011, 04:47 PM	#6
-xlr8planet- RCC Contributor Join Date: Feb 2008 Location: Buenos Aires, Argentina iTrader: (4) Posts: 679 Rep Power: 17	I really like the overall shape of the ports __________________ www.rx7club.com.ar RX-7 Forum in Spanish I make custom decals. Yes, you can ask me

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode