20b RCR Superlite-Coupe

lh6601 · 09-08-2010, 01:26 PM

I gotta go wack off

D4rw1n · 09-12-2010, 08:47 PM

sweet lord

incubus · 09-30-2010, 12:42 AM

Why is the lower chasis square + not round? Wouldn't that save you some weight + be a bit stronger?

Kentetsu · 09-30-2010, 01:42 PM

Wow, I've never seen one of those before! What the hell is it? What will you be using it for? Where can I find more info on the chassis/shell?

I think I just found the car to replace my fb with. Just as soon as a rich uncle dies and leaves me his accumulated wealth!

Anyway, that thing is just plain beautiful man. Must be a lot of fun building that thing up. Must give more photos, so find a reason to snap some for us if you could. Even the boring stuff will most likely have us drooling.

btw, where are you located? I'm sure you are far from me, but thought I'd ask anyway...

.

Gregory Casimir · 09-30-2010, 07:24 PM

wow really looking forward to more progress on this piece! what class racing are you aiming for?

RX-Heven · 10-01-2010, 01:34 PM

Quote:

Originally Posted by incubus

Why is the lower chasis square + not round? Wouldn't that save you some weight + be a bit stronger?

Perhaps, but that's how it was designed. I'll let the people who design these for a living be the judge of what is the best option. I understand about compromises but I don't think many were made when this was designed. The whole chassis is made from aluminum tubing, panels or solid billet. I've also made a few modifications here and there. It is plenty light and stiff, believe me. Goal is less than 2400 pounds wet with a/c, sound deadening etc. accompanied by 800 hp. In other words, better than 3hp/lb in street trim.

Quote:

Originally Posted by Kentetsu

What the hell is it? What will you be using it for? Where can I find more info on the chassis/shell?

http://www.superlitecars.com/
The car will be street legal and SCCA/NASA compliant. I'm building it the way I want while not being constrained by any class regulations. I will drive it on the streets and probably only time trial the car so it will either be in an Unlimited or Race class. The more time and money I put into it, the more I doubt I'll do any head-to-head racing with it but you never know.

Quote:

Originally Posted by Kentetsu

btw, where are you located? I'm sure you are far from me, but thought I'd ask anyway...

San Francisco

need RX7 · 10-01-2010, 03:19 PM

I seriously love this so much. The thought of a car built for pure speed with none of the compromises required for a 'street car' really tickles me in a special way

.

EDIT: Whoa, I just checked out their site and they're actually pretty close to where I live. I might have to go bother them someday

.

Kentetsu · 10-02-2010, 01:27 AM

Damn, all the cool shit happens out in Cali!

It blows my mind that this thing is going to be a street legal car. When you get it finished, maybe we'll take up a collection to get you out to the Deals Gap Rotary Rally.

Anyway, I think I might have just found my "project" for when I retire. Only 22 years to go. lol.

Thanks a lot for the information, I'll check that link out too. Very cool project you've got and I wish you the best of luck...

Edit: These guys are located in Michigan, so I guess I have to take back that comment about all the cool stuff being in Cali.

gmonsen · 12-16-2010, 10:57 PM

Rx-Heven... Dave, its really coming along. Any new pictures or updates? I spoke to the guy that runs RCR about a year or two ago. Great cars. I love both yours and the P4 bodies. I have really thought about this a fair amount. Originally with the Ultima and than more recently the RCR. Only thing that bothers me is the lack of opening windows. Are you good with the little sliding square plexi window and air conditioning?

Incubus... The RCR square tube, semi-monocoque chassis is absolutely state-of-the-art racing chassis design. A round or oval tube chassis could be made to be about as good, but assembly is a lot more accurate and quicker with square tubes. Their P4 is an updated version of Lee Noble's old P4 and Noble is the guy that designed the Ultima, so there's a lot of common lineage with some great cars.

Gordon

FerociousP · 12-17-2010, 12:33 AM

Quote:

Originally Posted by gmonsen

Rx-Heven... Dave, its really coming along. Any new pictures or updates? I spoke to the guy that runs RCR about a year or two ago. Great cars. I love both yours and the P4 bodies. I have really thought about this a fair amount. Originally with the Ultima and than more recently the RCR. Only thing that bothers me is the lack of opening windows. Are you good with the little sliding square plexi window and air conditioning?

Incubus... The RCR square tube, semi-monocoque chassis is absolutely state-of-the-art racing chassis design. A round or oval tube chassis could be made to be about as good, but assembly is a lot more accurate and quicker with square tubes. Their P4 is an updated version of Lee Noble's old P4 and Noble is the guy that designed the Ultima, so there's a lot of common lineage with some great cars.

Gordon

Gordon, not to change from the thread, but do you have pics of your current cars? The list in your sig is quite impressive. 850 6-speed, 3 20Bs... etc...

diabolical1 · 12-18-2010, 05:31 PM

this is an awesome project. where does it stand at the moment? any photos?

RX-Heven · 12-21-2010, 12:20 PM

Ordered a Phil Laird 20b UIM and am waiting on that to arrive to determine where I can stick the turbo and then design an exhaust manifold, intake plenum/tb and ic size/type and placement. It all depends on the UIM as space is tight for what I need.

Redone the engine mounts in billet aluminum and received some Tillett seats and am making billet seat mounts for them at the moment.

Before that though, I need to finish modifying my mill and actually make things with it, not for it.

funkspectrum · 12-21-2010, 01:02 PM

Quote:

Originally Posted by RX-Heven

Ordered a Phil Laird 20b UIM and am waiting on that to arrive to determine where I can stick the turbo and then design an exhaust manifold, intake plenum/tb and ic size/type and placement. It all depends on the UIM as space is tight for what I need.

Redone the engine mounts in billet aluminum and received some Tillett seats and am making billet seat mounts for them at the moment.

Before that though, I need to finish modifying my mill and actually make things with it, not for it.

Lookin good Dave!

I remember seeing that block under your workbench the last time I was at your house!

Been a while, man!

Erdin · 02-09-2011, 05:34 PM

any updates

Yasser_Hanbali13 · 02-09-2011, 11:12 PM

this is my only thought on this piece of art.

09-08-2010, 01:26 PM	#16
lh6601 Down with OPP Join Date: Mar 2010 iTrader: (0) Posts: 50 Rep Power: 15	I gotta go wack off __________________ 86 base, TII swapped, Rtek 2.1, some other things. Daily driven.

09-12-2010, 08:47 PM	#17
D4rw1n Sham-POW Join Date: Feb 2008 Location: Wilmington, NC iTrader: (0) Posts: 42 Rep Power: 0	sweet lord __________________ 93 VR Fake R1 PFC + LC-1 + Datalogit Full Non-Seq @ 12psi KGparts Diff Brace Fluidyne Radiator Tri-sports AST SS DP + MP + Catback Poor Mans Air Box Mod with K&N Walbro Fuel Pump http://fah-web.stanford.edu/cgi-bin/...teamnum=162255

09-30-2010, 01:42 PM	#19
Kentetsu RCC Contributor Join Date: Feb 2008 Location: Grand Rapids, Michigan iTrader: (1) Posts: 530 Rep Power: 17	Wow, I've never seen one of those before! What the hell is it? What will you be using it for? Where can I find more info on the chassis/shell? I think I just found the car to replace my fb with. Just as soon as a rich uncle dies and leaves me his accumulated wealth! Anyway, that thing is just plain beautiful man. Must be a lot of fun building that thing up. Must give more photos, so find a reason to snap some for us if you could. Even the boring stuff will most likely have us drooling. btw, where are you located? I'm sure you are far from me, but thought I'd ask anyway... . __________________ "Learn from the past, or it will become your future...." '85 GS 12a + LSD/Sterling carb/Respeed coilovers/Respeed front swaybar/Respeed adj. rear spring perches/Illuminas/Bilsteins on rear AutoX vids @ http://www.youtube.com/user/Kentetsu1

10-01-2010, 03:19 PM	#22
need RX7 Clean S4 Nutswinger Join Date: Mar 2008 Location: Sterling Heights, MI iTrader: (0) Posts: 485 Rep Power: 17	I seriously love this so much. The thought of a car built for pure speed with none of the compromises required for a 'street car' really tickles me in a special way . EDIT: Whoa, I just checked out their site and they're actually pretty close to where I live. I might have to go bother them someday . __________________ -Ted -1986 Mazda RX7 Sport [DD/beater]: engine finally let go at 205k. parts car status. -1986 Mazda RX7 base [resto-mod project]: S5 n/a swap in progress. Last edited by need RX7; 10-01-2010 at 03:21 PM..

12-16-2010, 10:57 PM	#24
gmonsen The Ancient One Join Date: Mar 2008 Location: Eastern Pennsylvania iTrader: (0) Posts: 144 Rep Power: 17	Rx-Heven... Dave, its really coming along. Any new pictures or updates? I spoke to the guy that runs RCR about a year or two ago. Great cars. I love both yours and the P4 bodies. I have really thought about this a fair amount. Originally with the Ultima and than more recently the RCR. Only thing that bothers me is the lack of opening windows. Are you good with the little sliding square plexi window and air conditioning? Incubus... The RCR square tube, semi-monocoque chassis is absolutely state-of-the-art racing chassis design. A round or oval tube chassis could be made to be about as good, but assembly is a lot more accurate and quicker with square tubes. Their P4 is an updated version of Lee Noble's old P4 and Noble is the guy that designed the Ultima, so there's a lot of common lineage with some great cars. Gordon __________________ 1993 Rx7 R1 20b NA 1994 Rx7 20b supercharged project 1991 BMW 850 6 speed 1991 BMW E30 M3 Evo II

09-30-2010, 12:42 AM	#18
incubus rotor's are in my blood Join Date: Sep 2010 iTrader: (0) Posts: 8 Rep Power: 0	Why is the lower chasis square + not round? Wouldn't that save you some weight + be a bit stronger?

09-30-2010, 07:24 PM	#20
Gregory Casimir Rotary Fanatic Join Date: Jan 2010 iTrader: (0) Posts: 253 Rep Power: 15	wow really looking forward to more progress on this piece! what class racing are you aiming for?

10-02-2010, 01:27 AM	#23
Kentetsu RCC Contributor Join Date: Feb 2008 Location: Grand Rapids, Michigan iTrader: (1) Posts: 530 Rep Power: 17	Damn, all the cool shit happens out in Cali! It blows my mind that this thing is going to be a street legal car. When you get it finished, maybe we'll take up a collection to get you out to the Deals Gap Rotary Rally. Anyway, I think I might have just found my "project" for when I retire. Only 22 years to go. lol. Thanks a lot for the information, I'll check that link out too. Very cool project you've got and I wish you the best of luck... Edit: These guys are located in Michigan, so I guess I have to take back that comment about all the cool stuff being in Cali.

12-18-2010, 05:31 PM	#26
diabolical1 I have radioactive semen Join Date: Jul 2008 Location: in a bottle of Glenfiddich iTrader: (0) Posts: 249 Rep Power: 17	this is an awesome project. where does it stand at the moment? any photos?

12-21-2010, 12:20 PM	#27
RX-Heven The Newbie Join Date: Feb 2008 iTrader: (0) Posts: 20 Rep Power: 0	Ordered a Phil Laird 20b UIM and am waiting on that to arrive to determine where I can stick the turbo and then design an exhaust manifold, intake plenum/tb and ic size/type and placement. It all depends on the UIM as space is tight for what I need. Redone the engine mounts in billet aluminum and received some Tillett seats and am making billet seat mounts for them at the moment. Before that though, I need to finish modifying my mill and actually make things with it, not for it. __________________ -Dave 20b RCR Superlite Coupe 91 Widebody Turbo Vert...RIP

02-09-2011, 05:34 PM	#29
Erdin The Newbie Join Date: Mar 2008 iTrader: (0) Posts: 18 Rep Power: 0	any updates

02-09-2011, 11:12 PM	#30
Yasser_Hanbali13 The Newbie Join Date: Feb 2011 Location: Columbus, Ohio iTrader: (0) Posts: 11 Rep Power: 0	this is my only thought on this piece of art.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode