|
|
|
||||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
 |
|
|
Thread Tools | Display Modes |
|
|
|
|
||||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
|
|
|
Thread Tools | Display Modes |
11-05-2010, 06:31 AM
|
#1 |
|
Rotary Fan in Training
|
13b series 6 and 5 speed help
ok, i want to fit a series 6 13b turbo, 13b series 5 5 speed, in my rx4 coupe. right hand drive as i am in japan.
will the 12a turbo timing cover fit the series 6 13b? so i can make it front mount. will series 5 5 speed mate to series 6 motor with series 5 bellhousing? let me know people. also, does 12a turbo distributor fit 13b series 6 motor? allowing me to use a fuel only computer. thanks guys ! |
|
|
|
11-05-2010, 10:58 AM
|
#2 | |
|
The fan hit the shit!
|
Ok, let me get this straight.
13b rew with s5 tranny in a rx4? If so the s5 tranny will bolt right up to the motor, and i'm not 100% sure but the front cover off the 12a should fit on the rew and then of cousre you will have to use a dizzy because the rew use crank pickup sensor rather than a cas like the rest of the 13b's. Zack.
__________________
87 TII= High comp 13b-re,S360,Link G4 RX  Quote:
|
|
|
|
|
|
11-05-2010, 02:14 PM
|
#3 | ||
|
RCC Addict
|
Quote:
-Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
|
||
|
|
|
|
11-05-2010, 02:15 PM
|
#4 | ||
|
RCC Addict
|
Quote:
-Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
|
||
|
|
|
|
11-05-2010, 03:31 PM
|
#5 | ||
|
Test Whore - Admin
|
Quote:
Quote:
__________________
-The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. -Angry Motherf*cker Mode ENGAGED- |
||
|
|
|
|
11-05-2010, 03:38 PM
|
#6 | |
|
The fan hit the shit!
|
Like i said i was not sure if the 12a cover would fit. Thanks now i know.
__________________
87 TII= High comp 13b-re,S360,Link G4 RX Quote:
|
|
|
|
|
|
11-05-2010, 08:18 PM
|
#7 |
|
Big Ugly
|
Early (S3) 13b front cover will definitely work, but I'm pretty sure there is more than a few 13b REW's using 12a covers.
__________________
Boosted Big Body On 335's PS3 ID: Rotordad 1986 Mazda RX7 GXL - Street ported 13BT, Haltech, 62mm, ect. 2006 MazdaSpeed 6 - Eagle, Wiseco, Cobb, ect. Last edited by RotorDad; 11-05-2010 at 08:26 PM.. |
|
|
|
|
11-05-2010, 10:22 PM
|
#8 |
|
The quest for more torque
|
I think if I recall correctly, the cover will bolt on, but the water pump will not bolt on after the cover is installed (they interfere). I know this is an issue between s4 and s5 and I am pretty sure that a 12a front cover will bolt on an s4.
__________________
1986 GXL ('87 4-port NA - Haltech E8, LS2 Coils. Defined Autoworks Headers, Dual 2.5" Exhaust (Dual Superflow, dBX mufflers) 1991 Coupe (KYB AGX Shocks, Eibach lowering springs, RB exhaust, Stock and Automatic) |
|
|
|
Linear Mode
