Length of brake lines

firzen · 06-15-2010, 06:32 AM

Does anybody know the lengths of brake lines on our car? I'm looking to completely redo my brake system with new tubing and am wondering if anybody else had pulled this off.

Cheers.

firzen · 06-19-2010, 11:56 PM

How come I always ask questions nobody can answer?

***TitaniumTT*** · 06-20-2010, 08:22 AM

I don't remember the length but I do remember that I just took a tailors tape measure and had at it. Called up Classis Tube, gave them the lengths and they cut and flared the ends with the tube nuts already on. They sent it in a coil so I had to straighten it, then bend it to where I wanted it. They can and have in the past completely redone lines in stainless. Meaning if you send them your old lines, they'll jig them and send you a new set. Not sure what the cost is on that.

The other thing to do would be to just buy a coil of the line and have a hydrualic shop flare the ends after you've got it bent where you want it.

firzen · 06-21-2010, 10:26 PM

I took my measuring tape out and got a rough estimate- it ain't easy to measure the full length of the pipes without removing any of them- and got around 25ft of 3/16" lines. Going to look again tomorrow and see how much 1/4" line I need.

I'm actually going to try the copper-nickel alloy stuff instead of SS. A couple of reputable shops in my area (including a proper race shop) recommended the stuff for its corrosion resistance and easy workability.

06-15-2010, 06:32 AM	#1
firzen Rotary Fanatic Join Date: Mar 2008 iTrader: (2) Posts: 231 Rep Power: 17	Length of brake lines Does anybody know the lengths of brake lines on our car? I'm looking to completely redo my brake system with new tubing and am wondering if anybody else had pulled this off. Cheers.

06-20-2010, 08:22 AM	#3
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I don't remember the length but I do remember that I just took a tailors tape measure and had at it. Called up Classis Tube, gave them the lengths and they cut and flared the ends with the tube nuts already on. They sent it in a coil so I had to straighten it, then bend it to where I wanted it. They can and have in the past completely redone lines in stainless. Meaning if you send them your old lines, they'll jig them and send you a new set. Not sure what the cost is on that. The other thing to do would be to just buy a coil of the line and have a hydrualic shop flare the ends after you've got it bent where you want it. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-19-2010, 11:56 PM	#2
firzen Rotary Fanatic Join Date: Mar 2008 iTrader: (2) Posts: 231 Rep Power: 17	How come I always ask questions nobody can answer?

06-21-2010, 10:26 PM	#4
firzen Rotary Fanatic Join Date: Mar 2008 iTrader: (2) Posts: 231 Rep Power: 17	I took my measuring tape out and got a rough estimate- it ain't easy to measure the full length of the pipes without removing any of them- and got around 25ft of 3/16" lines. Going to look again tomorrow and see how much 1/4" line I need. I'm actually going to try the copper-nickel alloy stuff instead of SS. A couple of reputable shops in my area (including a proper race shop) recommended the stuff for its corrosion resistance and easy workability.