FS: '93 Red FD 5 sp 508 rwhp

vincentrx7 · 09-30-2009, 06:17 PM

'93 RX7 5 speed Base model with SUPER RARE back seat (including seat belts). 89k on chasis. About 1k miles on half bridge port motor that made 508 rwhp. Exterior is red. Paint about 5 yrs old. Very slight hail damage. Interior is in overall pretty good condition for its age (I'd guess 8 out of 10). No peeling or discoloration from the sun (still nice and shiny black). It has a carbon fiber dash kit and shift knob, 2 pillar mounted gauges(AEM Boost controller and Wideband) and a carbon fiber steering column mount w/ Greddy fuel press. gauge. The handheld
Apexi Power FC controller is mounted next to the radio (with the Apexi black finish arm). The controller for the Coolingmist system is in the glovebox and the Greddy turbo timer is located in a compartment below the radio. You have everything you need to fully tune the car from the cockpit. Below is a list of engine modifications. Also all boost lines and engine wiring harness were replaced when the engine was done. It was dyno tuned with full meth at 20psi.
The car made 508rwhp
I'll provide the dyno sheet.
$18,500
Pics on the way!
Mods:

GT4094R Ballbearing Single Turbo w/ a turbo blanket heat shield
Stage 4 halfbridge ported motor w/ aviation seals
850cc primary injectors, 1600cc secondary
twin Bosch fuel pumps, one internal and one external
HKS Fuel rail
Apexi Power FC standalone ECU w/ commander unit
Coolingmist Vari-cool Meth injection kit w/ clog nozzel detection and commanderbunit
Greddy intake manifold
Polished Greddy Polished piping throughout
Greddy exhaust manifold
Greddy Racing wastegate Greddy
Type-R blowoff valve
Greddy SP exhaust w/ customized
Greddy downpipe HKS Twin Power ignition
Greddy FMIC
Koyo Radiator
AEM TRU Boost controller - pillar mounted
AEM UEGO Wideband with Bosch O2 sensor –
Greddy Fuel pressure guage
Greddy Turbo Timer
6 Puck sprung hub clutch
Unorthodox 9lb aluminum flywheel
Greddy Pulley set
Oil catch can installed

09-30-2009, 06:17 PM	#1
vincentrx7 20b FD Join Date: Apr 2008 Posts: 105 Rep Power: 17	FS: '93 Red FD 5 sp 508 rwhp '93 RX7 5 speed Base model with SUPER RARE back seat (including seat belts). 89k on chasis. About 1k miles on half bridge port motor that made 508 rwhp. Exterior is red. Paint about 5 yrs old. Very slight hail damage. Interior is in overall pretty good condition for its age (I'd guess 8 out of 10). No peeling or discoloration from the sun (still nice and shiny black). It has a carbon fiber dash kit and shift knob, 2 pillar mounted gauges(AEM Boost controller and Wideband) and a carbon fiber steering column mount w/ Greddy fuel press. gauge. The handheld Apexi Power FC controller is mounted next to the radio (with the Apexi black finish arm). The controller for the Coolingmist system is in the glovebox and the Greddy turbo timer is located in a compartment below the radio. You have everything you need to fully tune the car from the cockpit. Below is a list of engine modifications. Also all boost lines and engine wiring harness were replaced when the engine was done. It was dyno tuned with full meth at 20psi. The car made 508rwhp I'll provide the dyno sheet. $18,500 Pics on the way! Mods: GT4094R Ballbearing Single Turbo w/ a turbo blanket heat shield Stage 4 halfbridge ported motor w/ aviation seals 850cc primary injectors, 1600cc secondary twin Bosch fuel pumps, one internal and one external HKS Fuel rail Apexi Power FC standalone ECU w/ commander unit Coolingmist Vari-cool Meth injection kit w/ clog nozzel detection and commanderbunit Greddy intake manifold Polished Greddy Polished piping throughout Greddy exhaust manifold Greddy Racing wastegate Greddy Type-R blowoff valve Greddy SP exhaust w/ customized Greddy downpipe HKS Twin Power ignition Greddy FMIC Koyo Radiator AEM TRU Boost controller - pillar mounted AEM UEGO Wideband with Bosch O2 sensor – Greddy Fuel pressure guage Greddy Turbo Timer 6 Puck sprung hub clutch Unorthodox 9lb aluminum flywheel Greddy Pulley set Oil catch can installed __________________ Bobby '93 20b RX-7