Go Back   Rotary Car Club > Tech Discussion > Show your rotary car build up.

Show your rotary car build up. Show off your Rotary Car build!

 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 03-06-2017, 02:07 PM   #11
TitaniumTT
Test Whore - Admin
 
TitaniumTT's Avatar
 
Join Date: Mar 2008
Location: Right Behind you son
Posts: 4,581
Rep Power: 10
TitaniumTT will become famous soon enough
Quote:
Originally Posted by FC Zach View Post
So I swapped the clutch and installed the rebuilt transmission this weekend. The Centerforce Dual Friction I removed appears to still have a lot of life left on it, is there still a market for these? I'd sell it cheap if there's any interest in it.
Bring it to DGRR and wait for someone to blow a turbo clutch and sell it expensive. Of course I'll be the one looking for a clutch

Quote:
Originally Posted by FC Zach View Post
I had to remove the fancy coil mount kit to remove the long starter bolt and as I laid it to the side I felt something protruding from one of the coil-to-plug adapters. . here's what I found:

One of the detents for the plug weren't seated completely and the bad connection caused it to get hot enough to melt almost completely through the plastic housing.

I'm no longer going to be using the COP adapters and will be replacing them with tailored wired. I'll still use the coil mount, just not as it was intended.
Ruh Roh!

Quote:
Originally Posted by FC Zach View Post
Since the power harness was mostly disconnected, I completely removed it with hopes of replacing it with a new harness (mine is in very rough shape). I contacted Chris Ludwig to see if he can do this, if not does anyone have any recommendations on where this can be built or purchased?
I responded in your Alt thread.... otherwise there's always buying a new one for like $400.... they're still available per MazdaMotorsports
__________________
-The Angry Stig-
DGRR 2009, 2011, 2012 & 2013 - Best FC

DEALS GAP!! WOOHOOOO!!!!!

2015 Audi S4 - Samantha - Zero Brap S4
2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter
2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins
1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle
1988 'Vert - In progress
1988 FC Coupe - Gretchen -The attention whore BEAST!


I'm a sick individual, what's wrong with you?
I'm pure Evil
I'm still insane, in the best possible way.
I think Brian's idea of romance is using lube.
Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion.
You win with your thread. Most everything
It's a truck with a steel gate on the back. Just a statement of fact

Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff....
No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon.
-Angry Motherf*cker Mode ENGAGED-
TitaniumTT is offline   Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:54 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Hosted by www.GotPlacement.com