Go Back   Rotary Car Club > Tech Discussion > Rotary Tech - General Rotary Engine related tech section..
Reload this Page Bridge Port / Coolant Seal Question
Home Forum Classifieds Register FAQ Members List Calendar Mark Forums Read

Rotary Tech - General Rotary Engine related tech section.. Tech section for general Rotary Engine... This includes, building 12As, 13Bs, 20Bs, Renesis, etc...

 
 
Thread Tools Display Modes
\r\n \r\n\r\n \r\n\r\n \r\n \r\n\r\n \r\n \r\n
\r\n __________________
\r\n \r\n
\r\n \r\n \r\n\r\n \r\n\r\n \r\n\r\n \r\n\r\n\r\n \r\n staticpat is offline\r\n\r\n\r\n \r\n \r\n \r\n \r\n  \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n Reply With Quote\r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n\r\n\r\n\r\n\r\n\r\n\r\n\r\n\r\n\r\n \r\n \r\n \r\n \r\n\r\n\r\n\r\n\r\n'; pd[64076] = '\r\n\r\n \r\n\r\n
\r\n
\r\n
\r\n\r\n
\r\n \r\n\r\n\r\n\r\n\r\n\r\n \r\n \r\n \r\n \r\n\r\n\r\n \r\n\r\n\r\n \r\n \r\n \r\n\r\n
\r\n \r\n Old\r\n 12-18-2008, 12:52 PM\r\n \r\n \r\n \r\n  \r\n #2\r\n \r\n
\r\n\r\n
\r\n \r\n drewski86\r\n \r\n \r\n\r\n \r\n\r\n \r\n \r\n\r\n \r\n \r\n
\r\n __________________
\r\n
\r\n
Quote:
\r\n \r\n \r\n \r\n \r\n
\r\n \r\n
\r\n Originally Posted by djmtsu\r\n View Post\r\n
\r\n
Wars are started over beliefs. Ideas are safer.
\r\n \r\n
\r\n
\r\n
\r\n \r\n \r\n\r\n \r\n\r\n \r\n \r\n
\r\n
\r\n \r\n \r\n Last edited by classicauto; 12-19-2008 at 01:10 PM..\r\n \r\n \r\n \r\n
\r\n \r\n \r\n\r\n
\r\n classicauto is offline\r\n\r\n\r\n \r\n \r\n \r\n \r\n  \r\n \r\n \r\n \r\n \r\n \r\n \r\n Reply With Quote\r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n
\r\n\r\n\r\n\r\n\r\n\r\n\r\n\r\n
\r\n \r\n
\r\n
\r\n
\r\n\r\n\r\n\r\n'; pd[64281] = '\r\n\r\n \r\n\r\n
\r\n
\r\n
\r\n\r\n
\r\n \r\n\r\n\r\n\r\n\r\n\r\n \r\n \r\n \r\n \r\n\r\n\r\n
\r\n \r\n Old\r\n 12-19-2008, 12:00 PM\r\n \r\n \r\n \r\n  \r\n #17\r\n \r\n
\r\n\r\n
\r\n \r\n Whizbang\r\n
Prev Previous Post   Next Post Next
Old 12-18-2008, 11:22 AM   #1
staticpat
Rally Fanboy
 
staticpat's Avatar
 
Join Date: Feb 2008
Location: New York
iTrader: (1)
Posts: 147
Rep Power: 17
staticpat is on a distinguished road
Default Bridge Port / Coolant Seal Question
No Limit Industries is helping me get a half bridge motor running. It was built by a reputable shop, and has like 100 miles on it. The motor is installed in the car now, and we were about to install the intake manifold/carb setup. One of the guys stuck his finger into the intake ports and felt something out of place.

It looks like there's a little piece of gasket material hanging into the intake port. When we felt inside the other ports, they also had some material. I assume it is one of the water seals, that no longer has a place to seat because of the porting. I don't want to rip it out for fear that the whole seal will come with it. I don't want to leave it because it seems like an obstruction to flow.

I don't know enough about the porting procedures to know if this is bad or not. Any tips/advice/information would be greatly appreciate it. I'll call the builder this afternoon to get his opinion on it.









__________________
staticpat is offline   Reply With Quote
 

Bookmarks

« Previous Thread | Top | Next Thread »
Thread Tools
Display Modes
Threaded Mode Threaded Mode

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Forum Jump


All times are GMT -5. The time now is 11:23 PM.

Contact Us - Rotary Car Club - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Hosted by www.GotPlacement.com
Ad Management by RedTyger