|
|
|
||||||||
| Show your rotary car build up. Show off your Rotary Car build! |
|
|
Thread Tools | Display Modes |
|
|
|
|
||||||||
| Show your rotary car build up. Show off your Rotary Car build! |
|
|
Thread Tools | Display Modes |
\r\n\r\n\r\n \r\n \r\n \r\n \r\n \r\n 
\r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n  \r\n 04-04-2012, 08:12 AM\r\n \r\n \r\n | \r\n \r\n \r\n #2\r\n \r\n | \r\n \r\n
| \r\n\r\n \r\n \r\n Rx_sam\r\n
\r\n \r\n\r\n \r\n\r\n \r\n \r\n\r\n \r\n \r\n \r\n __________________ \r\n \r\n \r\n\r\n \r\n\r\n \r\n\r\n \r\n 1979 SA22C (parts of one anyway) \r\nhttp://rotarycarclub.com/rotary_foru...ad.php?t=15585 \r\n \r\n1975 MG Midget (building) \r\nhttp://rotarycarclub.com/rotary_foru...ad.php?t=18681 \r\n \r\n1988 N/A SE model FC, dead stock and less than 85k on the clock. This one actually runs, so I don\'t fuck with it.  \r\n | \r\n|
| \r\n \r\n\r\n\r\n \r\n \r\n \r\n \r\n \r\n | \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n | \r\n
| \r\n \r\n \r\n 05-26-2012, 12:18 AM\r\n \r\n \r\n | \r\n \r\n \r\n #17\r\n \r\n | \r\n \r\n
| \r\n\r\n \r\n \r\n Rx_sam\r\n
\r\n \r\n\r\n \r\n\r\n \r\n \r\n\r\n \r\n \r\n \r\n __________________ \r\n \r\n \r\n\r\n \r\n\r\n \r\n\r\n \r\n 1979 SA22C (parts of one anyway) \r\nhttp://rotarycarclub.com/rotary_foru...ad.php?t=15585 \r\n \r\n1975 MG Midget (building) \r\nhttp://rotarycarclub.com/rotary_foru...ad.php?t=18681 \r\n \r\n1988 N/A SE model FC, dead stock and less than 85k on the clock. This one actually runs, so I don\'t fuck with it. \r\n | \r\n|
| \r\n \r\n\r\n\r\n \r\n \r\n \r\n \r\n \r\n | \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n \r\n | \r\n
| \r\n \r\n \r\n 03-13-2013, 09:47 AM\r\n \r\n \r\n | \r\n \r\n \r\n #32\r\n \r\n | \r\n \r\n|||||
| \r\n\r\n \r\n \r\n Rx_sam\r\n
|
i can almost drive it. just need to go on the dyno and then technical control and then put it 5 cm lower because she's to high now
Threaded Mode