Eccentric shaft lock bolt removal

parrotfever · 08-18-2009, 01:27 PM

Help the newbie please! I've set the stage (photo upload failed - I'll try later) - prepped the area and scrounged every tool I could beg, borrow, or buy.

I've watched the videos I could find - I've read the FSM (which says to replace the Eccentric shaft lock bolt) - BUT...

Can someone please advise as to how to loosen this bolt? I tried an impact wrench to no avail. My guess is that its got threadlocker on it and that heat is the solution - but I'd rather hear from those who know BEFORE I screw up.

If so - how high (propane/MAP/acetylene) & how long? If not, then what?

I'm kinda desperately wanting to see what the mice did while living inside. How they got there is another question as the car had a full exhaust attached.

parrotfever Bob

Dzire · 08-18-2009, 01:37 PM

MAPP GAS work for me

***TitaniumTT*** · 08-18-2009, 02:40 PM

Impact has yet to fail me, then again, she's huge. Maybe stuff it in the back of a car/truck and head down to a tire shop?

parrotfever · 08-18-2009, 03:49 PM

Many thanks for the responses! I also found a thread that ran last year in Rotary Resurrection's forum (memo to self - look first, then look harder, Grasshopper). I used my 1/2" drive impact wrench but was concerned about undue stress by going larger. Left/right-hand thread was also a question in my mind. I'll go to heat & my 3/4" drive impact wrench next and see what happens.

parrotfever Bob

parrotfever · 08-18-2009, 08:02 PM

Oxy-Acetylene until the bolt head was cherry red & the 3/4" impact wrench did the trick! Thanks again.

parrotfever Bob

djmtsu · 08-18-2009, 08:16 PM

Good job!

I remember the last time I had to take one off, I used an impact socket with a makeshift 6 foot breaker bar!

Works everytime (the first time!!!)

Mobius · 08-18-2009, 09:41 PM

Quote:

Originally Posted by djmtsu

Good job!

I remember the last time I had to take one off, I used an impact socket with a makeshift 6 foot breaker bar!

Works everytime (the first time!!!)

Haha, exactly. It's either lots of heat and an impact or hanging off of an 8 foot breaker bar.

08-18-2009, 01:27 PM	#1
parrotfever Rotary Fan in Training Join Date: Jun 2009 Location: Northern NJ iTrader: (0) Posts: 37 Rep Power: 0	Eccentric shaft lock bolt removal Help the newbie please! I've set the stage (photo upload failed - I'll try later) - prepped the area and scrounged every tool I could beg, borrow, or buy. I've watched the videos I could find - I've read the FSM (which says to replace the Eccentric shaft lock bolt) - BUT... Can someone please advise as to how to loosen this bolt? I tried an impact wrench to no avail. My guess is that its got threadlocker on it and that heat is the solution - but I'd rather hear from those who know BEFORE I screw up. If so - how high (propane/MAP/acetylene) & how long? If not, then what? I'm kinda desperately wanting to see what the mice did while living inside. How they got there is another question as the car had a full exhaust attached. parrotfever Bob __________________ 1989 RX-7 convertible 2000 F-350 4x4 crew cab 2002 Altima 3.5 wife's buggy - 2004 Titan 4x4 crew cab

08-18-2009, 01:37 PM	#2
Dzire Rotary Fanatic Join Date: Apr 2008 Location: B,ham AL/Hollywood FL iTrader: (0) Posts: 151 Rep Power: 17	MAPP GAS work for me __________________ RX8 2004 GT RX7 1988 TII

08-18-2009, 02:40 PM	#3
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Impact has yet to fail me, then again, she's huge. Maybe stuff it in the back of a car/truck and head down to a tire shop? __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

08-18-2009, 03:49 PM	#4
parrotfever Rotary Fan in Training Join Date: Jun 2009 Location: Northern NJ iTrader: (0) Posts: 37 Rep Power: 0	Many thanks for the responses! I also found a thread that ran last year in Rotary Resurrection's forum (memo to self - look first, then look harder, Grasshopper). I used my 1/2" drive impact wrench but was concerned about undue stress by going larger. Left/right-hand thread was also a question in my mind. I'll go to heat & my 3/4" drive impact wrench next and see what happens. parrotfever Bob __________________ 1989 RX-7 convertible 2000 F-350 4x4 crew cab 2002 Altima 3.5 wife's buggy - 2004 Titan 4x4 crew cab Last edited by parrotfever; 08-18-2009 at 08:03 PM..

08-18-2009, 08:02 PM	#5
parrotfever Rotary Fan in Training Join Date: Jun 2009 Location: Northern NJ iTrader: (0) Posts: 37 Rep Power: 0	Oxy-Acetylene until the bolt head was cherry red & the 3/4" impact wrench did the trick! Thanks again. parrotfever Bob __________________ 1989 RX-7 convertible 2000 F-350 4x4 crew cab 2002 Altima 3.5 wife's buggy - 2004 Titan 4x4 crew cab

08-18-2009, 08:16 PM	#6
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Good job! I remember the last time I had to take one off, I used an impact socket with a makeshift 6 foot breaker bar! Works everytime (the first time!!!) __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode