FS: Crooked Willow Racing SMIC

zonblitz · 05-03-2009, 07:33 PM

Very Rare Crooked Willow Racing SMIC with CF duct, custom pipes with Greddy Type RS BOV Flang welded to cold side, includes Samco Couplers.
Pipes fit to Greddy elbow and Efini Y-pipe.

$1400 plus shipping.

zonblitz · 05-12-2009, 06:23 PM

SOLD Please close.

tnn · 10-30-2011, 09:47 PM

sorry to bring this thread back. if any have this setup for sell please pm me.

Rx7aholic · 12-27-2011, 09:21 PM

Dude u might as well look for something else, that setup is impossible to find.
Khris

tnn · 08-24-2012, 12:33 AM

well I didn't find it but got a custom made exactly like it

Trout2 · 08-24-2012, 01:30 AM

Hopefully you did something to seal tose big gaps where the end tanks taper.

Jack

tnn · 08-24-2012, 10:30 AM

It looks like gaps but actually not. The ic fit very tight. I was afraid to crack the duct trying to fit in

Rx7aholic · 10-03-2012, 07:54 PM

Nice not bad looking who made it for u? Also u can use some rubber seal (door type) I believe I got it from pepboys it's nice and soft so it contour around the duct, how muc that cost u btw?
Khris

05-12-2009, 06:23 PM	#2
zonblitz Rotary Fanatic Join Date: Feb 2008 Location: Pearl River, LA iTrader: (0) Posts: 166 Rep Power: 17	SOLD Please close. __________________ Kenny If you need a website, or know anyone who does, look me up: www.efiniconsulting.com

08-24-2012, 12:33 AM	#5
tnn The Newbie Join Date: Sep 2010 Location: Bay Area, CA iTrader: (0) Posts: 12 Rep Power: 0	well I didn't find it but got a custom made exactly like it Last edited by tnn; 08-24-2012 at 12:39 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

10-30-2011, 09:47 PM	#3
tnn The Newbie Join Date: Sep 2010 Location: Bay Area, CA iTrader: (0) Posts: 12 Rep Power: 0	sorry to bring this thread back. if any have this setup for sell please pm me.

12-27-2011, 09:21 PM	#4
Rx7aholic The Newbie Join Date: Mar 2008 iTrader: (0) Posts: 27 Rep Power: 0	Dude u might as well look for something else, that setup is impossible to find. Khris

08-24-2012, 01:30 AM	#6
Trout2 Rotary Fanatic Join Date: Mar 2008 iTrader: (0) Posts: 104 Rep Power: 17	Hopefully you did something to seal tose big gaps where the end tanks taper. Jack

08-24-2012, 10:30 AM	#7
tnn The Newbie Join Date: Sep 2010 Location: Bay Area, CA iTrader: (0) Posts: 12 Rep Power: 0	It looks like gaps but actually not. The ic fit very tight. I was afraid to crack the duct trying to fit in

10-03-2012, 07:54 PM	#8
Rx7aholic The Newbie Join Date: Mar 2008 iTrader: (0) Posts: 27 Rep Power: 0	Nice not bad looking who made it for u? Also u can use some rubber seal (door type) I believe I got it from pepboys it's nice and soft so it contour around the duct, how muc that cost u btw? Khris