FC3S Murray's never ending build.

FC3S Murray · 02-27-2010, 11:52 AM

Quote:

Originally Posted by TitaniumTT

Meh, I'm happy with my stances. Be warned though, this might apply to the BC's, if your tires are sticky enough the rear trailing arm will flex enough on hard turns and chew into the housing on the C/O At idle there's a decent gap, but put enough load on that sucker..... bad things will happen :'(

Good to know Brian, I will have to ask one of my buddies here in town who has some BC's installed on his FC. He drives it very hard and has had those C/O's for 3-4 years now.

MAN I am sorry to see all that rot under your FC....really blows. Knowing you though, you'll find a way to patch it up and make it look better then it came out of the factory.

***TitaniumTT*** · 02-28-2010, 01:23 AM

Yeah, def ask him about it... it's serious hard cornering though. As in my tires were rubbing the heat shield on the muffler! That's alot of flex. I ALMOST went and swapped the rear swing arm bushings for the AWR bearing version to take car of it.

Thanks man, I'm around the corner, over the hump, and I'll have some pics up in my Diary Thread, lemme know.... I think I did the factory proud

FC3S Murray · 03-12-2010, 01:55 PM

..............I am losing my fucking mind! BC Racing contacted me today and said the coilovers won't even ship until Monday. I have been waiting a month...not cool.

However I have almost got my water injection research wrapped up and am pretty confident in what I want to run in my set-up.

The weather is getting very nice and I am losing my patience....I could be putting miles on the motOr

project86 · 03-15-2010, 10:40 PM

....i didnt know moter was spelled with an e.....

FC3S Murray · 03-16-2010, 01:34 PM

F. O.

project86 · 03-19-2010, 04:11 PM

Quote:

Originally Posted by FC3S Murray

F. O.

Sean im gonna ignore that... lucky for you. Im requiring you to let me know when you get your BCs so i can come over and drool on them.

FC3S Murray · 03-20-2010, 05:37 PM

Found my damn camera so here are some pics in high qaulity

Pic of the install of my Black Energy Suspension bushing kit and a Racing Beat Front sway bar. I installed all the bushings except for the rear lower contol arm WHICH worked out to my advantage since you CAN'T have the MMR rear camber adjusters installed unless you have the factory bushing installed OR a sperical bushing since polys will not budge causing binding issues

Gave me a chance to clean up down there too...................

** little tip here for anyone going to install E.S. Bushings for the rear sway bar endlink: You have to install the top bolt inboard-to-outborad or it will hit your body pinch weld

Here are the MMR rear camber adjusters installed on the car. They adjust ON the car btw......

Since I was in a polishing mood with the wheels my Mothers Alum Polish found its way to my compressor housing too

and the intercooler piping ( I need to start working on cleaning up the damn clutter in my engine bay)....

FC3S Murray · 03-20-2010, 05:37 PM

Wheel Shots

closest "on the car" shots I can give you for now

some outside shots

Rear Wheel 17x9 +28

Front Wheel 17x8 +29

Think I should put them on the Wife's Rouge.....

Gregory Casimir · 03-20-2010, 05:56 PM

^^^they actually look pretty dope on the rouge lol

project86 · 03-21-2010, 12:47 AM

i dig it

FC3S Murray · 03-25-2010, 09:39 PM

A little tease for everybody

BC's came in today, I have them installed but am dialing in the FC right now. Pics and review of coilovers and the FC ON THE GROUND will be very very soon

need RX7 · 03-25-2010, 09:57 PM

:drool:

Looks so good.

***TitaniumTT*** · 03-25-2010, 09:57 PM

I need a towel.

So HOT Sean, looks fucking AMAZING. Still LOVE that color.

chibikougan · 03-26-2010, 09:03 AM

Oooh you will have to bring it out Saturday and let me touch you. I mean it! Damnit I mean your car! Haha

FC3S Murray · 03-30-2010, 06:09 PM

Finally an update:

So I figure I will start off with giving a small review so far on the BC Racing type BR coilovers......these things:

I am very impressed by the qaulity especially since they are made in Taiwan. The coilovers came with a 1 year warrenty, the necessary adjustment tools, some product info and a SWEET decal! The whole assembly in general was solid and the craftsmanship impressive, BEST part was the include a brake line clip

Camber plates very nice BUT they peg out at -1.5 degrees because of the allen bolts hitting the bulkhead. The Dampner is fully adjustable with 30 settings.

The install on the car was easy and they came preloaded. I would say judging from when I first put the FC on the ground, the ride hieght was about stock...maybe slightly lower. They adjust just like any other coilover and I will say that the threaded cylinder turned easily IF you loosen the rear and front lower arm bolts.

Total time to install and adjust the ride hieght accordenly was around 4 hours. I used a digital vernier caliper to measure the distance from the bottom lock ring to the small preload lock ring. This ensured linear drop. I DID have to drop the passenger front a 1/2 inch more then the drivers side though to get equal fender gap.

I also have MAXED out my MMR Rear Camber adjusters(bolt fully tightened and bottomed out)) and I am in the -1.2 degree camber in the rear.

02-28-2010, 01:23 AM	#392
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Yeah, def ask him about it... it's serious hard cornering though. As in my tires were rubbing the heat shield on the muffler! That's alot of flex. I ALMOST went and swapped the rear swing arm bushings for the AWR bearing version to take car of it. Thanks man, I'm around the corner, over the hump, and I'll have some pics up in my Diary Thread, lemme know.... I think I did the factory proud __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-12-2010, 01:55 PM	#393
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	..............I am losing my fucking mind! BC Racing contacted me today and said the coilovers won't even ship until Monday. I have been waiting a month...not cool. However I have almost got my water injection research wrapped up and am pretty confident in what I want to run in my set-up. The weather is getting very nice and I am losing my patience....I could be putting miles on the motOr __________________ Same pig, new soul Last edited by FC3S Murray; 03-16-2010 at 01:34 PM..

03-15-2010, 10:40 PM	#394
project86 Can't.Make.Up.My.Mind. Join Date: May 2009 Location: Murfreesboro, TN iTrader: (3) Posts: 1,377 Rep Power: 17	....i didnt know moter was spelled with an e..... __________________ '90 GTUs Stay up to date with my photography '06 Toyota Highlander Hybrid '10 Toyota Prius "Initial Success or Total Failure"

03-16-2010, 01:34 PM	#395
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	F. O. __________________ Same pig, new soul

03-20-2010, 05:37 PM	#397
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	Found my damn camera so here are some pics in high qaulity Pic of the install of my Black Energy Suspension bushing kit and a Racing Beat Front sway bar. I installed all the bushings except for the rear lower contol arm WHICH worked out to my advantage since you CAN'T have the MMR rear camber adjusters installed unless you have the factory bushing installed OR a sperical bushing since polys will not budge causing binding issues Gave me a chance to clean up down there too................... ** little tip here for anyone going to install E.S. Bushings for the rear sway bar endlink: You have to install the top bolt inboard-to-outborad or it will hit your body pinch weld Here are the MMR rear camber adjusters installed on the car. They adjust ON the car btw...... Since I was in a polishing mood with the wheels my Mothers Alum Polish found its way to my compressor housing too and the intercooler piping ( I need to start working on cleaning up the damn clutter in my engine bay).... __________________ Same pig, new soul

03-20-2010, 05:37 PM	#398
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	Wheel Shots closest "on the car" shots I can give you for now some outside shots Rear Wheel 17x9 +28 Front Wheel 17x8 +29 Think I should put them on the Wife's Rouge..... __________________ Same pig, new soul

03-20-2010, 05:56 PM	#399
Gregory Casimir Rotary Fanatic Join Date: Jan 2010 iTrader: (0) Posts: 253 Rep Power: 15	^^^they actually look pretty dope on the rouge lol

03-21-2010, 12:47 AM	#400
project86 Can't.Make.Up.My.Mind. Join Date: May 2009 Location: Murfreesboro, TN iTrader: (3) Posts: 1,377 Rep Power: 17	i dig it __________________ '90 GTUs Stay up to date with my photography '06 Toyota Highlander Hybrid '10 Toyota Prius "Initial Success or Total Failure"

03-25-2010, 09:39 PM	#401
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	A little tease for everybody BC's came in today, I have them installed but am dialing in the FC right now. Pics and review of coilovers and the FC ON THE GROUND will be very very soon __________________ Same pig, new soul Last edited by FC3S Murray; 03-25-2010 at 10:17 PM..

03-25-2010, 09:57 PM	#402
need RX7 Clean S4 Nutswinger Join Date: Mar 2008 Location: Sterling Heights, MI iTrader: (0) Posts: 485 Rep Power: 17	:drool: Looks so good. __________________ -Ted -1986 Mazda RX7 Sport [DD/beater]: engine finally let go at 205k. parts car status. -1986 Mazda RX7 base [resto-mod project]: S5 n/a swap in progress.

03-25-2010, 09:57 PM	#403
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I need a towel. So HOT Sean, looks fucking AMAZING. Still LOVE that color. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-26-2010, 09:03 AM	#404
chibikougan ⊙⊙ Join Date: Dec 2009 Location: Great Falls iTrader: (4) Posts: 1,258 Rep Power: 16	Oooh you will have to bring it out Saturday and let me touch you. I mean it! Damnit I mean your car! Haha

03-30-2010, 06:09 PM	#405
FC3S Murray frustrated! Join Date: Apr 2009 Location: Montana iTrader: (3) Posts: 611 Rep Power: 16	Finally an update: So I figure I will start off with giving a small review so far on the BC Racing type BR coilovers......these things: I am very impressed by the qaulity especially since they are made in Taiwan. The coilovers came with a 1 year warrenty, the necessary adjustment tools, some product info and a SWEET decal! The whole assembly in general was solid and the craftsmanship impressive, BEST part was the include a brake line clip Camber plates very nice BUT they peg out at -1.5 degrees because of the allen bolts hitting the bulkhead. The Dampner is fully adjustable with 30 settings. The install on the car was easy and they came preloaded. I would say judging from when I first put the FC on the ground, the ride hieght was about stock...maybe slightly lower. They adjust just like any other coilover and I will say that the threaded cylinder turned easily IF you loosen the rear and front lower arm bolts. Total time to install and adjust the ride hieght accordenly was around 4 hours. I used a digital vernier caliper to measure the distance from the bottom lock ring to the small preload lock ring. This ensured linear drop. I DID have to drop the passenger front a 1/2 inch more then the drivers side though to get equal fender gap. I also have MAXED out my MMR Rear Camber adjusters(bolt fully tightened and bottomed out)) and I am in the -1.2 degree camber in the rear. __________________ Same pig, new soul Last edited by FC3S Murray; 03-30-2010 at 06:33 PM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode