Cup holder in progress

Rx-7fetish · 03-01-2011, 02:33 AM

So tired of holding my drinks in my lap and so far not having seen any other decent cup holder options I have decided to embark on my own fabrication. First off let me state that this really isn't a viable option for someone with power mirrors unless you move the mirror switch. Or just adjust them then unplug the switch. I have non power aero mirrors so I decided to get rid of the switch.

I then traced the whole rectangle piece onto a piece of aluminum I had, moved the square where the security light clips in up further and this is what I have so far.

My next step will be to take some measurements and get a general drink size whole cut out on the bigger lower portion of the new plate. Then take another larger cup or something of that sort and cut the bottom portion off and affix to the bottom of the plate. So the hole isn't just open to under the center console. I also plan to line the top edge of holder with foam or something of that sort so it can hold a variety of drink sizes snug. My other worry is that I might need to build up higher from the top of the plate if this turns out to be to shallow if just made level with the plate.

speedjunkie · 03-01-2011, 02:38 AM

Awesome. You might be starting a movement with this haha.

Rx-7fetish · 03-01-2011, 11:46 AM

Questions, comments, suggestions, anyone?

***TitaniumTT*** · 03-01-2011, 11:53 AM

I don't think that area will be deep enough to securely hold a drink

Rx-7fetish · 03-01-2011, 01:29 PM

Quote:

Originally Posted by Rx-7fetish

My other worry is that I might need to build up higher from the top of the plate if this turns out to be to shallow if just made level with the plate.

..

***TitaniumTT*** · 03-01-2011, 01:42 PM

Just emphasising that I feel it won't be deep enough. What's the test? Take a few hard turns and wait to see if some sticky stinky soda gets spilled and soaks into the carpet, electronics, and seats? I'd build it up from the start.

Rx-7fetish · 03-01-2011, 01:44 PM

I do plan to make some sort of arms or fingers to grip the drink, like so,

But yes I do think I will cut a few more layers of aluminum into squares and cut progressively bigger holes in them as the layers go up

My5ABaby · 03-01-2011, 04:37 PM

Or fiberglas.

Rx-7fetish · 03-01-2011, 05:16 PM

Quote:

Originally Posted by My5ABaby

Or fiberglas.

i already own the aluminum in small enough chunks that its not really useful for much else, also no money for the glass. im just doin a prototype i guess you could say, your welcome to use whatever material to see fit. Also i thought of the raised ring but decided against it due to my elbow being in the area when there is no drink, i dont want to break it off, plus i think maybe a quarter to a half inch thinker just around the cup holder area would be more aesthetically pleasing. this will all also be getting painted black, or grey, not sure yet.

Rx-7fetish · 03-01-2011, 05:34 PM

Behold! I am a master of Paint!!!

Roen · 03-01-2011, 04:54 PM

Why not build a second ring that's raised over the panel for extra security? That + grips in the hole should provide for a semi-secure fit.

03-01-2011, 02:33 AM	#1
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor iTrader: (0) Posts: 211 Rep Power: 0	Cup holder in progress So tired of holding my drinks in my lap and so far not having seen any other decent cup holder options I have decided to embark on my own fabrication. First off let me state that this really isn't a viable option for someone with power mirrors unless you move the mirror switch. Or just adjust them then unplug the switch. I have non power aero mirrors so I decided to get rid of the switch. I then traced the whole rectangle piece onto a piece of aluminum I had, moved the square where the security light clips in up further and this is what I have so far. My next step will be to take some measurements and get a general drink size whole cut out on the bigger lower portion of the new plate. Then take another larger cup or something of that sort and cut the bottom portion off and affix to the bottom of the plate. So the hole isn't just open to under the center console. I also plan to line the top edge of holder with foam or something of that sort so it can hold a variety of drink sizes snug. My other worry is that I might need to build up higher from the top of the plate if this turns out to be to shallow if just made level with the plate. Last edited by Rx-7fetish; 03-01-2011 at 05:39 PM..

03-01-2011, 11:53 AM	#4
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I don't think that area will be deep enough to securely hold a drink __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-01-2011, 01:42 PM	#6
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Just emphasising that I feel it won't be deep enough. What's the test? Take a few hard turns and wait to see if some sticky stinky soda gets spilled and soaks into the carpet, electronics, and seats? I'd build it up from the start. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-01-2011, 01:44 PM	#7
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor iTrader: (0) Posts: 211 Rep Power: 0	I do plan to make some sort of arms or fingers to grip the drink, like so, But yes I do think I will cut a few more layers of aluminum into squares and cut progressively bigger holes in them as the layers go up Last edited by Rx-7fetish; 03-01-2011 at 01:48 PM..

03-01-2011, 04:37 PM	#8
My5ABaby Sigh..... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (6) Posts: 2,377 Rep Power: 19	Or fiberglas. __________________ 1986 Sport: 132k miles, 5A (Sapphire Blue Metallic), Tokico Blues, Racing Beat Springs, Custom LED tailights (only S4 LED tails in the world), SSR Mark II, Racing Beat exhaust, S5 black interior, Rotary Resurrection rebuild at 120k miles Community Service Manual RotorWiki "Imagination costs nothing; we could build square locomotives or fly to Mars" - Felix Wankel Yesterday is history, tomorrow is a mystery, but today is a gift. That is why it is called the "present."

03-01-2011, 02:38 AM	#2
speedjunkie RCC Loves Me Not You Join Date: Mar 2008 Location: Colorado Springs, CO iTrader: (1) Posts: 2,089 Rep Power: 19	Awesome. You might be starting a movement with this haha.

03-01-2011, 11:46 AM	#3
Rx-7fetish Blue Blur Join Date: Jan 2009 Location: Windsor iTrader: (0) Posts: 211 Rep Power: 0	Questions, comments, suggestions, anyone?

03-01-2011, 04:54 PM	#11
Roen Evil Club Mod Join Date: Feb 2008 iTrader: (0) Posts: 183 Rep Power: 17	Why not build a second ring that's raised over the panel for extra security? That + grips in the hole should provide for a semi-secure fit. __________________ Ex-King of the Loop / Captain Guardrail / Master Crab Rapist / Evil Crop Dusting Mod