RX8 Front cover mod for 13B and 13BT

Phoenix7 · 06-12-2010, 04:02 AM

I was talking to Higgi about my issues with the pulley boss and how I needed to remove the front cover to make sure the needle bearings were seated right before torquing the new pulley boss. Long-story short I needed a new gasket and he mentioned that the RX8 gasket was a better choice but it needed to be modified. Very easy.

Have to cut the sections that don't line up without damaging the crush ring (hotlinking pics isn't working anymore)

The info came from this site:
http://www.rotaryheads.com/modificat...asket_mod.html

1. the RX8 gasket is metal vs. the paper ones for the FC
2. The FC front cover gasket is $25 + $4.75 for the Water pump housing-to-block gasket vs. $16 for the RX8 gasket W/ waterpump gasket.
3. It should help with the common leaky front cover.

I'll post pics of it if you want but it's self-explanatory, plus the pics from the site in the site are clear enough

End results:

You can find the gaskets from Atkins:
http://atkinsrotary.com/store/catalo...p-1-c-800.html

Note that this also works for the REW.

FC Zach · 06-12-2010, 05:33 AM

Nice, I learn something new every day. Going gasket less is an even cheaper and just as effective option, with little modification. I like the fact that the 8 gasket is made of steel. Is it a design similar to head gaskets?? like thin multi layer and coated gaskets?

Ender · 06-12-2010, 06:04 AM

HA! Cool. I'll have to remember this.

***TitaniumTT*** · 06-12-2010, 07:18 AM

13B-RE front cover gaskets are metal and require no modifications

N390-10-502

They're not like head gaskets. They're stamped with a raised area in the center. They are also reuseable if you're careful.

Nismo · 07-21-2010, 11:24 AM

Quote:

Originally Posted by TitaniumTT

13B-RE front cover gaskets are metal and require no modifications

N390-10-502

They're not like head gaskets. They're stamped with a raised area in the center. They are also reuseable if you're careful.

Good to know, I wish mine came with one!

firzen · 06-12-2010, 09:10 PM

Good stuff. Subscribed.

Phoenix7 · 07-17-2010, 02:57 AM

Stickied in archives...

classicauto · 07-21-2010, 10:42 AM

I notice that it goes across the pesky o-ring area.

Does the gasket take the place of the oring there? Or does it just take the place of the oring "holder" and still requires the oring to be installed?

Phoenix7 · 07-21-2010, 10:42 PM

Quote:

Originally Posted by classicauto

I notice that it goes across the pesky o-ring area.

Does the gasket take the place of the oring there? Or does it just take the place of the oring "holder" and still requires the oring to be installed?

The front cover-to-housing o-ring and nylon washer? Yes, you still need both of those. The gasket goes on AFTER you install the new ring/washer.

diabolical1 · 08-06-2010, 02:07 PM

finally! a mod that i can use, at a time when i can use it.

06-12-2010, 05:33 AM	#2
FC Zach RCC Loves Me Not You Join Date: Mar 2008 Location: Eagleville, TN iTrader: (2) Posts: 2,267 Rep Power: 19	Nice, I learn something new every day. Going gasket less is an even cheaper and just as effective option, with little modification. I like the fact that the 8 gasket is made of steel. Is it a design similar to head gaskets?? like thin multi layer and coated gaskets? __________________ 1993 Yamaha GTS1000 1992 Celica Turbo AllTrac 1987 RX7 Sport 1979 Yamaha G1, KM24 powered 1975 Dolmar KMS4

06-12-2010, 07:18 AM	#4
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	13B-RE front cover gaskets are metal and require no modifications N390-10-502 They're not like head gaskets. They're stamped with a raised area in the center. They are also reuseable if you're careful. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

06-12-2010, 09:10 PM	#6
firzen Rotary Fanatic Join Date: Mar 2008 iTrader: (2) Posts: 231 Rep Power: 17	Good stuff. Subscribed.

08-06-2010, 02:07 PM	#10
diabolical1 I have radioactive semen Join Date: Jul 2008 Location: in a bottle of Glenfiddich iTrader: (0) Posts: 249 Rep Power: 17	finally! a mod that i can use, at a time when i can use it.