running but alil slugish and back fireing?????

rotaryguy481 · 04-09-2010, 08:06 PM

Ok I finally got it to stay running and everything I have been posting a lot on here lately I changed the spark plugs and now it runs but really slugish and popping and all what else could it be

djmtsu · 04-09-2010, 08:11 PM

Wicked vacuum leak, blown engine, timing WAYY off, bad gas....

Alot of variables.

rotaryguy481 · 04-09-2010, 09:02 PM

Well I know the motors not bad less than two thousand miles on it and would a blow off valve not hooked up right cause a big vac leak and the gas could be to and the guy i got it from mixed way to much oil with the gas as well.

jerd_hambone · 04-09-2010, 09:08 PM

A BOV could cause a vac leak, but I don't know if it'd cause the car to run sluggish and backfire.

Was the motor broken in done properly?

rotaryguy481 · 04-09-2010, 09:58 PM

Yeah im pretty sure it was what are the requirements

jerd_hambone · 04-09-2010, 10:36 PM

http://www.rotaryresurrection.com/2n...p_breakin.html

rotaryguy481 · 04-09-2010, 10:44 PM

Aight I just asked the guy he told me pretty much everything that was in the thread

rotaryguy481 · 04-10-2010, 08:57 AM

And the compression is 115 front and back

jerd_hambone · 04-10-2010, 10:07 AM

Hm.

rotaryguy481 · 04-10-2010, 03:25 PM

I'm starting to think its the afm or bad coil or wires cause when you touch where the boot meets the wire it shocks the piss out of ya

My5ABaby · 04-10-2010, 03:48 PM

Did you put the right wires on the right plugs?

rotaryguy481 · 04-10-2010, 07:10 PM

IS L1 AND T1 the front rotor and L2 T2 the rear

rotaryguy481 · 04-11-2010, 11:10 AM

Ok I unplugged the pressure sensor and it runs just fine but when I plugged it back in runs like crappy

rotaryguy481 · 04-11-2010, 08:07 PM

Ok got a ajustable fpr what should I put the pressure at

FC3S · 04-12-2010, 05:45 AM

Search much? Throwing any codes? TPS adjusted properly?

04-09-2010, 08:06 PM	#1
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	running but alil slugish and back fireing????? Ok I finally got it to stay running and everything I have been posting a lot on here lately I changed the spark plugs and now it runs but really slugish and popping and all what else could it be

04-09-2010, 08:11 PM	#2
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Wicked vacuum leak, blown engine, timing WAYY off, bad gas.... Alot of variables. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

04-10-2010, 03:48 PM	#11
My5ABaby Sigh..... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (6) Posts: 2,377 Rep Power: 19	Did you put the right wires on the right plugs? __________________ 1986 Sport: 132k miles, 5A (Sapphire Blue Metallic), Tokico Blues, Racing Beat Springs, Custom LED tailights (only S4 LED tails in the world), SSR Mark II, Racing Beat exhaust, S5 black interior, Rotary Resurrection rebuild at 120k miles Community Service Manual RotorWiki "Imagination costs nothing; we could build square locomotives or fly to Mars" - Felix Wankel Yesterday is history, tomorrow is a mystery, but today is a gift. That is why it is called the "present."

04-09-2010, 09:02 PM	#3
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	Well I know the motors not bad less than two thousand miles on it and would a blow off valve not hooked up right cause a big vac leak and the gas could be to and the guy i got it from mixed way to much oil with the gas as well.

04-09-2010, 09:58 PM	#5
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	Yeah im pretty sure it was what are the requirements

04-09-2010, 10:44 PM	#7
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	Aight I just asked the guy he told me pretty much everything that was in the thread

04-10-2010, 08:57 AM	#8
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	And the compression is 115 front and back

04-10-2010, 03:25 PM	#10
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	I'm starting to think its the afm or bad coil or wires cause when you touch where the boot meets the wire it shocks the piss out of ya

04-10-2010, 07:10 PM	#12
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	IS L1 AND T1 the front rotor and L2 T2 the rear

04-11-2010, 11:10 AM	#13
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	Ok I unplugged the pressure sensor and it runs just fine but when I plugged it back in runs like crappy

04-11-2010, 08:07 PM	#14
rotaryguy481 Rotary Fan in Training Join Date: Jan 2010 Location: Fort Worth TX iTrader: (0) Posts: 74 Rep Power: 15	Ok got a ajustable fpr what should I put the pressure at

04-12-2010, 05:45 AM	#15
FC3S The Newbie Join Date: Apr 2010 iTrader: (0) Posts: 2 Rep Power: 0	Search much? Throwing any codes? TPS adjusted properly?