No more adjustment on TPS

phantomworks · 09-08-2008, 01:51 PM

I have installed a new TPS on my car and I've run out of adjustment?.

While adjusting the TPS I'm getting the proper closed/narrow voltage readings but when I try to adjust the TPS to get my WOT voltage correct I can't get anymore then 3.58 and 3.84.
The TPS will not rotate anymore on throttle body, I checked the throttle cable adjustment and it"s fine and the TPS was installed correctly.

What do you guy's think?

Spindoctor · 09-09-2008, 07:38 PM

Sounds like the tabs may be on the wrong side....take it off and reinstall it

phantomworks · 09-09-2008, 08:09 PM

No they are not on the wrong side, In fact I took it off and reinstalled it again today with the same results.

Phoenix7 · 09-09-2008, 08:22 PM

bad TPS? I don't understand, the screw just won't turn anymore?

phantomworks · 09-09-2008, 09:15 PM

Brand new TPS from Ray Crowe, I hope it's not bad. The TPS won"t rotate anymore on the throttle body.

I'm wondering if there is just a voltage drain on the system. maybe a bad ground?

Spindoctor · 09-10-2008, 08:42 PM

Perhaps you could remove it one more time and run it through its limits detached from the TB to see if it's even capable of reaching specified voltages. That may rule out a few things right off the bat. Is the harness in good condition? Have you tried probing the wires right at the connector?

phantomworks · 09-11-2008, 12:47 PM

Great idea I'll try it off the throttle body, thanks.
I'm probing right where the wires go into the connector

cewrx7r1 · 09-13-2008, 05:08 PM

Are you opening the throttle 100%?
If you are not doing it manually at the TB, you can't ber sure unless you have had your linkage checked out.

09-08-2008, 01:51 PM	#1
phantomworks The Newbie Join Date: May 2008 iTrader: (0) Posts: 21 Rep Power: 0	No more adjustment on TPS I have installed a new TPS on my car and I've run out of adjustment?. While adjusting the TPS I'm getting the proper closed/narrow voltage readings but when I try to adjust the TPS to get my WOT voltage correct I can't get anymore then 3.58 and 3.84. The TPS will not rotate anymore on throttle body, I checked the throttle cable adjustment and it"s fine and the TPS was installed correctly. What do you guy's think?

09-13-2008, 05:08 PM	#8
cewrx7r1 The Judge Join Date: Feb 2008 iTrader: (0) Posts: 196 Rep Power: 17	Are you opening the throttle 100%? If you are not doing it manually at the TB, you can't ber sure unless you have had your linkage checked out. Last edited by cewrx7r1; 09-15-2008 at 09:54 AM..

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

09-09-2008, 07:38 PM	#2
Spindoctor The Newbie Join Date: Mar 2008 iTrader: (0) Posts: 27 Rep Power: 0	Sounds like the tabs may be on the wrong side....take it off and reinstall it

09-09-2008, 08:09 PM	#3
phantomworks The Newbie Join Date: May 2008 iTrader: (0) Posts: 21 Rep Power: 0	No they are not on the wrong side, In fact I took it off and reinstalled it again today with the same results.

09-09-2008, 09:15 PM	#5
phantomworks The Newbie Join Date: May 2008 iTrader: (0) Posts: 21 Rep Power: 0	Brand new TPS from Ray Crowe, I hope it's not bad. The TPS won"t rotate anymore on the throttle body. I'm wondering if there is just a voltage drain on the system. maybe a bad ground?

09-10-2008, 08:42 PM	#6
Spindoctor The Newbie Join Date: Mar 2008 iTrader: (0) Posts: 27 Rep Power: 0	Perhaps you could remove it one more time and run it through its limits detached from the TB to see if it's even capable of reaching specified voltages. That may rule out a few things right off the bat. Is the harness in good condition? Have you tried probing the wires right at the connector?

09-11-2008, 12:47 PM	#7
phantomworks The Newbie Join Date: May 2008 iTrader: (0) Posts: 21 Rep Power: 0	Great idea I'll try it off the throttle body, thanks. I'm probing right where the wires go into the connector