Puslastion damper/banjo bolt mod

DriftingFC · 06-16-2008, 07:21 PM

ok. Im not ready (fund wise) to upgrade to full stainless braided fuel system. I dont want to risk blowing my dampner either. So, what size/where can I find a banjo bolt to replace my damper?

Please, damper lovers, dont bash and say what a bad Idea blah blah blah, just keep your opinion to yourself.

TehMonkay · 06-16-2008, 07:30 PM

Quote:

Originally Posted by DriftingFC

ok. Im not ready (fund wise) to upgrade to full stainless braided fuel system. I dont want to risk blowing my dampner either. So, what size/where can I find a banjo bolt to replace my damper?

Please, damper lovers, dont bash and say what a bad Idea blah blah blah, just keep your opinion to yourself.

Drill and tap for 3/8" NPT port and put an adapter for a 5/16" barb fitting on the end.

RETed · 06-16-2008, 07:33 PM

Summit Racing or anyone that carries Earls fittings...
http://fc3spro.com/TECH/FAQ/pd.html

-Ted

Phoenix7 · 06-16-2008, 07:38 PM

is yours leaking?

DriftingFC · 06-17-2008, 08:30 AM

Quote:

Originally Posted by phoenix7

is yours leaking?

Not yet. But since this is a track car more then a daily driver, I dont want to risk blowing the PD at the track. Plus Im about 8k into this car and I refuse to let it burn to the ground.

Howru · 06-17-2008, 01:35 AM

I took a banjo bolt from a spare S4 NA rail -- not sure if it was primary or secondary. It stuck out about 1/4" so I shortened the bolt with a bench grinder.

Good thing I tested with the spare primary rail: I kept wrenching the banjo bolt until it split. Whoops.

Phoenix7 · 06-17-2008, 10:42 AM

buy a spare and repair when it leaks? Do an inspection after every track event and stay on top of it. Be prepared but don't do unnecessary work.

DriftingFC · 06-17-2008, 11:06 AM

The season is half over, and Im just getting into it. I am going to do the Banjo bolt to finish the rest of the season, then do a complete braided setup with an FPR when I redo the car over the winter.

TehMonkay · 06-17-2008, 04:25 PM

Quote:

Originally Posted by DriftingFC

The season is half over, and Im just getting into it. I am going to do the Banjo bolt to finish the rest of the season, then do a complete braided setup with an FPR when I redo the car over the winter.

just bring the pd to a store than sells banjo blots and get a similar one?

expecially if its not your daily driver

Phoenix7 · 06-17-2008, 11:10 AM

ok. Get the old PD pressure tested (if it's not expensive) when you're done to see how it's been holding up all these years.

06-16-2008, 07:21 PM	#1
DriftingFC Rotary Fan in Training Join Date: Feb 2008 Location: Pittsburgh iTrader: (0) Posts: 81 Rep Power: 17	Puslastion damper/banjo bolt mod ok. Im not ready (fund wise) to upgrade to full stainless braided fuel system. I dont want to risk blowing my dampner either. So, what size/where can I find a banjo bolt to replace my damper? Please, damper lovers, dont bash and say what a bad Idea blah blah blah, just keep your opinion to yourself.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

06-17-2008, 01:35 AM	#6
Howru Louvers! Join Date: Mar 2008 Location: Vallejo, CA iTrader: (3) Posts: 66 Rep Power: 17	I took a banjo bolt from a spare S4 NA rail -- not sure if it was primary or secondary. It stuck out about 1/4" so I shortened the bolt with a bench grinder. Good thing I tested with the spare primary rail: I kept wrenching the banjo bolt until it split. Whoops.

06-17-2008, 11:06 AM	#8
DriftingFC Rotary Fan in Training Join Date: Feb 2008 Location: Pittsburgh iTrader: (0) Posts: 81 Rep Power: 17	The season is half over, and Im just getting into it. I am going to do the Banjo bolt to finish the rest of the season, then do a complete braided setup with an FPR when I redo the car over the winter.