TII oil pump on n/a engine.

need RX7 · 05-24-2011, 05:40 PM

I seem to recall reading somewhere that the TII oil pump flows more than the n/a oil pump, and that the TII oil pump is a direct swap onto an n/a engine.

Assuming the above is true, is it worth it? I plan on doing autocross and maybe the occasional track day, but it's not a serious race car. The engine (S5 n/a) is on a stand, and I plan on replacing the front cover gasket, so doing the pump would be easy while I'm in there.

diabolical1 · 05-24-2011, 09:00 PM

true on both counts. if you already have one, then by all means put it in. if you're asking if you should specifically buy one because you'll have the front cover off, then i'm really not sure. i mean i believe every little bit counts (if you can get the parts) but i wouldn't impose that on you.

Redshft · 05-25-2011, 07:34 AM

As above, true.
Personally, given the pain of swapping the oil pump while the engine is in the car should you have to later, and the consequences of an oil system vs. the cost of a new pump, it's certainly not a bad idea while you have the front cover off.
But, it really comes down to the existing pump. Is it reasonably new, or is it the original pump or of unknown origin? It's it original/unknown, I'd put in a new one just to feel better.

j9fd3s · 05-26-2011, 11:25 AM

the Turbo pump is larger, so it flows more oil, which is good.

if you've got it apart, put the turbo pump in, but i wouldn't take it apart just to put the turbo pump in, too much work for that

Libor · 05-26-2011, 05:40 PM

I´ve been thinking about some thing. Pump has fixed volume and flow is directly tied to engine RPMs - till pressure regulator starts bleeding excess oil back to the pan. So when we will fit bigger volume oil pump, we will hit regulated pressure in earlier RPMs but then, flow is very same, granted that we use same regulator.

I know that this is done regularly, but I think there are some misunderstands in flow, pressure etc.

05-24-2011, 05:40 PM	#1
need RX7 Clean S4 Nutswinger Join Date: Mar 2008 Location: Sterling Heights, MI iTrader: (0) Posts: 485 Rep Power: 17	TII oil pump on n/a engine. I seem to recall reading somewhere that the TII oil pump flows more than the n/a oil pump, and that the TII oil pump is a direct swap onto an n/a engine. Assuming the above is true, is it worth it? I plan on doing autocross and maybe the occasional track day, but it's not a serious race car. The engine (S5 n/a) is on a stand, and I plan on replacing the front cover gasket, so doing the pump would be easy while I'm in there. __________________ -Ted -1986 Mazda RX7 Sport [DD/beater]: engine finally let go at 205k. parts car status. -1986 Mazda RX7 base [resto-mod project]: S5 n/a swap in progress.

05-25-2011, 07:34 AM	#3
Redshft Rotary Fan in Training Join Date: Feb 2010 Location: Halifax, Nova Scotia, Canada iTrader: (0) Posts: 78 Rep Power: 15	As above, true. Personally, given the pain of swapping the oil pump while the engine is in the car should you have to later, and the consequences of an oil system vs. the cost of a new pump, it's certainly not a bad idea while you have the front cover off. But, it really comes down to the existing pump. Is it reasonably new, or is it the original pump or of unknown origin? It's it original/unknown, I'd put in a new one just to feel better. __________________ 2004 RX8 GT 1986 RX7 Track Car: 13B Bridge Port w/ Renesis Internals and Weber Carb 2003 MazdaSpeed Protege 1988 RX7 Convertible - new project 2004 Impreza and 2003 Legacy wagons for hauling groceries and The Dog

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

05-26-2011, 11:25 AM	#4
j9fd3s Rotary Fanatic Join Date: Mar 2008 iTrader: (0) Posts: 123 Rep Power: 17	the Turbo pump is larger, so it flows more oil, which is good. if you've got it apart, put the turbo pump in, but i wouldn't take it apart just to put the turbo pump in, too much work for that

05-26-2011, 05:40 PM	#5
Libor Rotary Fan in Training Join Date: Aug 2010 iTrader: (0) Posts: 54 Rep Power: 15	I´ve been thinking about some thing. Pump has fixed volume and flow is directly tied to engine RPMs - till pressure regulator starts bleeding excess oil back to the pan. So when we will fit bigger volume oil pump, we will hit regulated pressure in earlier RPMs but then, flow is very same, granted that we use same regulator. I know that this is done regularly, but I think there are some misunderstands in flow, pressure etc.