Question about 10AE

jfaplanet · 03-28-2008, 06:18 PM

I have acquired a 10AE, that was disassembled when I got it. My question is this. Since its an 88, and some 88's had low impedance injectors and some had high. Which is it. The car came with 3 motors and several harnesses. I have no clue as to which harness goes in the car. I am going to start trying to put the car back together after deals gap, so anyone that can assist me with info it is much appreciated. Thanks in advance, Charles

Phoenix7 · 03-28-2008, 07:31 PM

I believe the 87 turbos were LOW IMPEDANCE and the 88+ turbos were HIGH IMPEDANCE.

The cutoff is 1987.5.

Anything NEWER = high
anything OLDER = Low (will come with a resistor)

Wait until others verify though.

My5ABaby · 03-28-2008, 07:44 PM

http://www.rotaryresurrection.com/2n...ctor_info.html

Match up the injectors to the injector clips.

Rotary_Rocket_87 · 03-28-2008, 08:34 PM

Yeah, 87.5 was the cutoff point. your 10AE should have high impedance injectors. I would suggest taking the wiring harnesses apart (don't mix them together) and check for bad spots in the wires before installing in the car. This will prevent a big headache in the future and give you some assurance that you won't have a wiring issue. If you have a bad wire or two in a harness replace it with the "twin" wire from one of the other harnesses.

You could even go so far as completely disassembling the harness, reusing the plugs and connectors (after they have been thoroughly cleaned) and replacing all of the wire, using the factory wires as a template.

jfaplanet · 03-28-2008, 09:13 PM

Guys that is great info. I'm an old school mazda guy and this is my first FC. REPU, SA, FB are all I have ever owned. This is great. Thanks again.

03-28-2008, 06:18 PM	#1
jfaplanet Rotary Fanatic Join Date: Feb 2008 Location: Smyrna, TN iTrader: (0) Posts: 134 Rep Power: 17	Question about 10AE I have acquired a 10AE, that was disassembled when I got it. My question is this. Since its an 88, and some 88's had low impedance injectors and some had high. Which is it. The car came with 3 motors and several harnesses. I have no clue as to which harness goes in the car. I am going to start trying to put the car back together after deals gap, so anyone that can assist me with info it is much appreciated. Thanks in advance, Charles

03-28-2008, 09:13 PM	#5
jfaplanet Rotary Fanatic Join Date: Feb 2008 Location: Smyrna, TN iTrader: (0) Posts: 134 Rep Power: 17	Thanks Guys that is great info. I'm an old school mazda guy and this is my first FC. REPU, SA, FB are all I have ever owned. This is great. Thanks again.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

03-28-2008, 07:44 PM	#3
My5ABaby Sigh..... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (6) Posts: 2,377 Rep Power: 19	http://www.rotaryresurrection.com/2n...ctor_info.html Match up the injectors to the injector clips.

03-28-2008, 08:34 PM	#4
Rotary_Rocket_87 2nd Generation Freak Join Date: Mar 2008 Location: Chuck Vegas, NH iTrader: (0) Posts: 64 Rep Power: 17	Yeah, 87.5 was the cutoff point. your 10AE should have high impedance injectors. I would suggest taking the wiring harnesses apart (don't mix them together) and check for bad spots in the wires before installing in the car. This will prevent a big headache in the future and give you some assurance that you won't have a wiring issue. If you have a bad wire or two in a harness replace it with the "twin" wire from one of the other harnesses. You could even go so far as completely disassembling the harness, reusing the plugs and connectors (after they have been thoroughly cleaned) and replacing all of the wire, using the factory wires as a template.