do these look ok?

dr50376272 · 10-26-2010, 10:59 PM

tell me what you think of this bridgeporting work

Force13b · 10-27-2010, 12:45 PM

They look OK to me but i'm not a motor builder.

RotorDad · 10-27-2010, 03:27 PM

I think they look fine, but it is just a picture. Why are you asking, who did the porting?

***TitaniumTT*** · 10-27-2010, 08:25 PM

I see a few things wrong with them, but you're not taking pics of the important parts

rxspeed7 · 11-03-2010, 04:58 PM

^ very true. what is the timing degrees of the opening and closing events?

Have you used an old rotor to make sure the leading side seal is still supported and that the trailing side seal doesn't scissor into the closing of the port causing it to chip?.
Otherwise they don't look too bad. good job man!!

Zack.

10-27-2010, 03:27 PM	#3
RotorDad Big Ugly Join Date: Apr 2009 Location: Fredericksburg, Va iTrader: (1) Posts: 591 Rep Power: 16	I think they look fine, but it is just a picture. Why are you asking, who did the porting? __________________ *Boosted Big Body On 335's* PS3 ID: Rotordad 1986 Mazda RX7 GXL - Street ported 13BT, Haltech, 62mm, ect. 2006 MazdaSpeed 6 - Eagle, Wiseco, Cobb, ect.

10-27-2010, 08:25 PM	#4
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I see a few things wrong with them, but you're not taking pics of the important parts __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

10-27-2010, 12:45 PM	#2
Force13b cxxxx\|::::::::::::> Join Date: Nov 2009 iTrader: (1) Posts: 315 Rep Power: 16	They look OK to me but i'm not a motor builder.

11-03-2010, 04:58 PM	#5
rxspeed7 The fan hit the shit! Join Date: Nov 2010 Location: ocala,fl iTrader: (0) Posts: 152 Rep Power: 15	^ very true. what is the timing degrees of the opening and closing events? Have you used an old rotor to make sure the leading side seal is still supported and that the trailing side seal doesn't scissor into the closing of the port causing it to chip?. Otherwise they don't look too bad. good job man!! Zack.