HEAVY engine vibration

sen2two · 03-30-2010, 02:59 PM

(not my car)

S5 TII fresh rebuilt motor, timing is good, TPS is good, has spark/fuel to both rotors, no vacuum leaks, AFM is good...

Hard to start without holding the pedal down slightly. when it actually does idle at around 650-700 it sounds ok, not great, but ok. the second you try and rev it up, the engine shakes VERY HARD. The higher the RPM the worse it shakes. Its kinda similar to running on one rotor, but not so much...

any ideas? im stuck here...

Kentetsu · 03-31-2010, 06:50 AM

I'd check the ignition to make sure he's still got spark, but really it sounds like he tossed an apex seal.

.

classicauto · 03-31-2010, 10:46 AM

whats the story on the plugs?

Seen new plugs foul almost instantly from being gobbed with vaseline/assembly lube after the first start up. I'd toss a fresh set in and just see what happens.

sen2two · 03-31-2010, 10:50 AM

Quote:

Originally Posted by classicauto

whats the story on the plugs?

Seen new plugs foul almost instantly from being gobbed with vaseline/assembly lube after the first start up. I'd toss a fresh set in and just see what happens.

thats was my first guess also. no luck... Its using B9ES plugs also, wich are plugs for jet skis. And are EXTREMELY hard to foul out. Thats the reason i use them for start up... I also use them in my personal car year round.

sen2two · 03-31-2010, 10:48 AM

not an apex seal. its a fresh rebuild with RA seals. has great spark to all four plugs also...

never seen anything like this before. the only thing that comes to mind is kinda far fetched... Maybe someone in the past swapped rotors in this motor. the rotors could be far enough off balance to cause this vibration.

classicauto · 03-31-2010, 11:02 AM

I dunno about the mismatch rotors. I've run a S4 flywheel on an S5 (out of necesity for a breif period of time) and even with that I didn't really get any vibration you could detect just running the car. I'm sure it was wobbling due to the rear bearing being shot after

but no noticeable engine vibration at all. And I'd think that difference is greater then one wrong weight rotor......but....its uncertain.

Usually a heavy vibration like this is a misfire - which system its related to though I can't say for sure but would bet ignition.

Have you tried rotating the CAS with it runnning and revving and see if gets worse or better?

***TitaniumTT*** · 03-31-2010, 11:30 AM

Quote:

Originally Posted by classicauto

whats the story on the plugs?

Seen new plugs foul almost instantly from being gobbed with vaseline/assembly lube after the first start up. I'd toss a fresh set in and just see what happens.

That would be my first guess as well. I've had new plugs foul within 15 minutes of running from being gobbed up. Just all of sudden lost rotor..... stupid D580 coils

Quote:

Originally Posted by classicauto

I dunno about the mismatch rotors. I've run a S4 flywheel on an S5 (out of necesity for a breif period of time) and even with that I didn't really get any vibration you could detect just running the car. I'm sure it was wobbling due to the rear bearing being shot after

but no noticeable engine vibration at all. And I'd think that difference is greater then one wrong weight rotor......but....its uncertain.

Usually a heavy vibration like this is a misfire - which system its related to though I can't say for sure but would bet ignition.

Have you tried rotating the CAS with it runnning and revving and see if gets worse or better?

Maybe of it's two rotors from different series, different weights it might be off enough to FUBAR it.

My guess would be start at the ignition. Just becuase they're new plugs doesn't mean they;re not fouled. Just becuase they're new wired doesn't mean they're fuctioning properly. Just becuase they're new injectors, doesnt' mean they work either..... speaking of, what the story behind the injectors? I've heard rumors about the cleaning agents they use corroding the injector's frozen if they sit for long enough after a cleaning. Might wannaa send them out and see if they're in tip top shape.

FerociousP · 03-31-2010, 11:14 AM

djmtsu's engine had good (tested) compression, spark, ran "ok" but not great at idle, sounding like it was running on one rotor but "not", and would make crazy noises when revved... he determined he lost an injector (or a good injector went weak/clogged/etc.) while driving and eventually spun a bearing which now has low oil pressure..

how's your oil pressure?

djmtsu · 03-31-2010, 11:34 AM

Does it sound like this:

Lastphaseofthis · 03-31-2010, 11:26 PM

wow.. ^ that shit's fucked up.

OP,-maybe flywheel is not on properly? or it sheared the key? take it off and look.

Max777 · 04-01-2010, 12:35 PM

I had a the center bushing in my transmission cross member sag and break, when I put in the Banzai Poly bushings, it was terrible. Bought a new crossmember, and it got a lot better. I still need to replace my drive shaft and tires, but otherwise I cna drive the car under 50mph. I also think I have soem high rpm hesitations because the resistance on my TPS reads 7.1K at WOT, when it should read around 6K tops.

Hope this info helps somewhat.

sen2two · 04-02-2010, 08:51 PM

Well, the plugs look great but, i'll try a new set anyway... I was also just informed that the gas thats in the tank has been there for over 2 years.

Hopefully some new gas will remedy this...

***TitaniumTT*** · 04-02-2010, 10:20 PM

Yeah, I'd also send out those injectors as well. If the gas has been sitting that long, the injectors have probably been idle that long and I would think could use a little lovin'

sen2two · 04-02-2010, 11:28 PM

lol... cars not mine. As far as i knew, the gas was fairly new.

sen2two · 04-04-2010, 04:57 PM

new gas, new plugs... same problem.

WTF...

03-30-2010, 02:59 PM	#1
sen2two KTEC Join Date: Jan 2009 iTrader: (2) Posts: 642 Rep Power: 0	HEAVY engine vibration (not my car) S5 TII fresh rebuilt motor, timing is good, TPS is good, has spark/fuel to both rotors, no vacuum leaks, AFM is good... Hard to start without holding the pedal down slightly. when it actually does idle at around 650-700 it sounds ok, not great, but ok. the second you try and rev it up, the engine shakes VERY HARD. The higher the RPM the worse it shakes. Its kinda similar to running on one rotor, but not so much... any ideas? im stuck here... __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

03-31-2010, 06:50 AM	#2
Kentetsu RCC Contributor Join Date: Feb 2008 Location: Grand Rapids, Michigan iTrader: (1) Posts: 530 Rep Power: 17	I'd check the ignition to make sure he's still got spark, but really it sounds like he tossed an apex seal. . __________________ "Learn from the past, or it will become your future...." '85 GS 12a + LSD/Sterling carb/Respeed coilovers/Respeed front swaybar/Respeed adj. rear spring perches/Illuminas/Bilsteins on rear AutoX vids @ http://www.youtube.com/user/Kentetsu1

03-31-2010, 10:48 AM	#5
sen2two KTEC Join Date: Jan 2009 iTrader: (2) Posts: 642 Rep Power: 0	not an apex seal. its a fresh rebuild with RA seals. has great spark to all four plugs also... never seen anything like this before. the only thing that comes to mind is kinda far fetched... Maybe someone in the past swapped rotors in this motor. the rotors could be far enough off balance to cause this vibration. __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

03-31-2010, 11:14 AM	#8
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	djmtsu's engine had good (tested) compression, spark, ran "ok" but not great at idle, sounding like it was running on one rotor but "not", and would make crazy noises when revved... he determined he lost an injector (or a good injector went weak/clogged/etc.) while driving and eventually spun a bearing which now has low oil pressure.. how's your oil pressure? __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

03-31-2010, 11:34 AM	#9
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Does it sound like this: __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-31-2010, 11:26 PM	#10
Lastphaseofthis The Newbie Join Date: Apr 2008 Location: Mobile, AL iTrader: (0) Posts: 13 Rep Power: 0	wow.. ^ that shit's fucked up. OP,-maybe flywheel is not on properly? or it sheared the key? take it off and look.

04-01-2010, 12:35 PM	#11
Max777 Pirate Join Date: Mar 2008 Location: Central IL iTrader: (5) Posts: 1,323 Rep Power: 18	I had a the center bushing in my transmission cross member sag and break, when I put in the Banzai Poly bushings, it was terrible. Bought a new crossmember, and it got a lot better. I still need to replace my drive shaft and tires, but otherwise I cna drive the car under 50mph. I also think I have soem high rpm hesitations because the resistance on my TPS reads 7.1K at WOT, when it should read around 6K tops. Hope this info helps somewhat. __________________ Rotaries:They are NOT that complicated!

04-02-2010, 08:51 PM	#12
sen2two KTEC Join Date: Jan 2009 iTrader: (2) Posts: 642 Rep Power: 0	Well, the plugs look great but, i'll try a new set anyway... I was also just informed that the gas thats in the tank has been there for over 2 years. Hopefully some new gas will remedy this... __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

04-02-2010, 10:20 PM	#13
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	Yeah, I'd also send out those injectors as well. If the gas has been sitting that long, the injectors have probably been idle that long and I would think could use a little lovin' __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

04-02-2010, 11:28 PM	#14
sen2two KTEC Join Date: Jan 2009 iTrader: (2) Posts: 642 Rep Power: 0	lol... cars not mine. As far as i knew, the gas was fairly new. __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

04-04-2010, 04:57 PM	#15
sen2two KTEC Join Date: Jan 2009 iTrader: (2) Posts: 642 Rep Power: 0	new gas, new plugs... same problem. WTF... __________________ what I have: 1985 Gs:12a All motor Drag car - 1973 Rx2: Play car What I had: 93 Touring: TRADED - 91 Coupe: TRADED - 90 GTU: RHD - 88 10AE: SOLD - 87 Base: SOLD - 86 Base: SOLD - 1985 GSLSE - 85 Gsl: SOLD - 80 Gs: TRADED - 1972 Rx2

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode