Renesis engines, purchasing

djmtsu · 03-21-2010, 01:08 PM

I am very curious about this....

Why do people sell used renesis engines (condition essentially unknown to the buyer) for $1500 and up?

I can purchase one at the local dealership as a crate reman for right under $2000.

So, what gives?

***TitaniumTT*** · 03-21-2010, 02:07 PM

I think the used engine is a complete longblock with all the expensive manis, expensive OMPs, WP, TPS, injectors etc etc etc. The crate from the dealership is just the keg correct? If you're doing an engine swap it makes alot more sense to get the used and take a chance becuase all the other parts will cost more than $1500.

j9fd3s · 07-28-2011, 10:04 AM

Quote:

Originally Posted by TitaniumTT

I think the used engine is a complete longblock with all the expensive manis, expensive OMPs, WP, TPS, injectors etc etc etc. The crate from the dealership is just the keg correct? If you're doing an engine swap it makes alot more sense to get the used and take a chance becuase all the other parts will cost more than $1500.

the mazda reman comes with the water pump flywheel and oil pan.

when i was looking at doing an Rx8 swap (vs the PP) in 2006 i priced out all the intakes and fuel real stuff, its like $5k!

djmtsu · 03-21-2010, 02:22 PM

I guess. But I have seen short blocks for $1500.

A Mazda Reman with warranty for under 2k is awesome.

FerociousP · 03-21-2010, 07:40 PM

i thought he said $2100??

djmtsu · 03-21-2010, 07:59 PM

That is retail, he said it could be cheaper.

Even $2100 is a good deal.

ROTORX7Holly · 03-23-2010, 10:05 PM

Check out www.mazmart.com for renesis rebuilt by Rick Engman. I know a while back he had them for like $2K. If you contact them, ask for Paul. Strange, I cannot find the MazMart vendor here. Where did they go?

1Revvin7 · 03-26-2010, 02:38 PM

Mazda remans have poor rebuild quality, we are rebuilding a couple right now . They didn't even last 40k...

Lastphaseofthis · 03-27-2010, 11:13 AM

Quote:

Originally Posted by 1Revvin7

Mazda remans have poor rebuild quality, we are rebuilding a couple right now . They didn't even last 40k...

Can you tell what parts were replaced, and what was not? what was the failure mode if you don't mind? water jacket? i've seen one rx-8 that lost compression, but i was never told why, the guy was to busy trying to sell it to me.

stinksause · 11-14-2011, 02:05 AM

Quote:

Originally Posted by 1Revvin7

Mazda remans have poor rebuild quality, we are rebuilding a couple right now . They didn't even last 40k...

I heard a rumor that mazda uses jails to build their remans

1Revvin7 · 03-27-2010, 06:24 PM

The two I have seen lost compression from too much side seal clearance and worn out apex seals. Rotor housings and bearings were shot too. Sideseal clearance was in the .024"+ range. It appears to be they replace just soft and hard seals...

djmtsu · 03-31-2010, 06:49 AM

I know a guy

$1850 plus a refundable $1000 core charge.

FerociousP · 03-31-2010, 07:43 AM

its more like... he "knows" a guy 8===@

fc3sfreak415 · 07-27-2011, 02:22 PM

If your lookin for an engine give nation wide auto recycling a call. They have 2 engines for sale for $1700 they both are used and under 60k with one year warranty on them and no core charge

NATIONWIDE AUTO RECYCLING
978-534-0477 EXT 305

reddozen · 07-28-2011, 07:59 AM

I got my short block for $1000 Shipped. I'd much rater go that route and have it rebuilt by someone fairly reputable than to risk anything with a factory Mazda reman. As mentioned, their clearances / tolerances are pretty sloppy. Hand cut side seals FTW.

03-21-2010, 01:08 PM	#1
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	Renesis engines, purchasing I am very curious about this.... Why do people sell used renesis engines (condition essentially unknown to the buyer) for $1500 and up? I can purchase one at the local dealership as a crate reman for right under $2000. So, what gives? __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-21-2010, 02:07 PM	#2
*TitaniumTT* Test Whore - Admin Join Date: Mar 2008 Location: Right Behind you son iTrader: (4) Posts: 4,581 Rep Power: 10	I think the used engine is a complete longblock with all the expensive manis, expensive OMPs, WP, TPS, injectors etc etc etc. The crate from the dealership is just the keg correct? If you're doing an engine swap it makes alot more sense to get the used and take a chance becuase all the other parts will cost more than $1500. __________________ -The Angry Stig- DGRR 2009, 2011, 2012 & 2013 - Best FC DEALS GAP!! WOOHOOOO!!!!! 2015 Audi S4 - Samantha - Zero Brap S4 2004 RX8 - Jocelyn - 196rwhp, 19mpg fuel to noise converter 2000 Jeep Cherokee Sport - Wifey mobile - Now with 2.5" OME lift and 30" BFG AT KO's! So it begins 1998 Jeep Cherokee - 5 spd, 4" lift, 33" BFG's - Rotary Tow Vehicle 1988 'Vert - In progress 1988 FC Coupe - Gretchen -The attention whore BEAST! I'm a sick individual, what's wrong with you? I'm pure Evil I'm still insane, in the best possible way. I think Brian's idea of romance is using lube. Your rage caused the meteor strike in Russia. The Antichrist would be proud of his minion. You win with your thread. Most everything It's a truck with a steel gate on the back. Just a statement of fact Motec M820, AIM dash, ported 13B-RE Cosmo, 6-spd trans, 4.3 Torsen, custom twin wg fully divided mani, Custom 4" split into 2x 3" exhaust, Custom HMIC, Custom custom custom custom I like to welder stuff.... No Bolt-ons allowed. Dyno'ed @ Speed1 Tuned by me - 405rwhp on WG.... WM50 cuming soon. *-Angry Motherfcker Mode ENGAGED-**

03-21-2010, 02:22 PM	#4
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	I guess. But I have seen short blocks for $1500. A Mazda Reman with warranty for under 2k is awesome. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-21-2010, 07:40 PM	#5
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	i thought he said $2100?? __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

03-21-2010, 07:59 PM	#6
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	That is retail, he said it could be cheaper. Even $2100 is a good deal. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-23-2010, 10:05 PM	#7
ROTORX7Holly Rotary Fanatic Join Date: Mar 2008 Location: Atlanta iTrader: (0) Posts: 364 Rep Power: 17	Check out www.mazmart.com for renesis rebuilt by Rick Engman. I know a while back he had them for like $2K. If you contact them, ask for Paul. Strange, I cannot find the MazMart vendor here. Where did they go? __________________ 2004 RX-8 Back in a Rotary again - March, 2010 2005 Mazda3i .. Purchased Aug. 05.. Daily Zoom Zoomed from Apr., 07 to Mar., 10 Original Owner of 93 VR Base, ...SOLD April 20, 2007.

03-26-2010, 02:38 PM	#8
1Revvin7 Turblown Engineering Join Date: Feb 2008 Location: AZ iTrader: (0) Posts: 62 Rep Power: 17	Mazda remans have poor rebuild quality, we are rebuilding a couple right now . They didn't even last 40k...

03-27-2010, 06:24 PM	#11
1Revvin7 Turblown Engineering Join Date: Feb 2008 Location: AZ iTrader: (0) Posts: 62 Rep Power: 17	The two I have seen lost compression from too much side seal clearance and worn out apex seals. Rotor housings and bearings were shot too. Sideseal clearance was in the .024"+ range. It appears to be they replace just soft and hard seals...

03-31-2010, 06:49 AM	#12
djmtsu My minds tellin' me no... Join Date: Feb 2008 Location: Murfreesboro, TN iTrader: (10) Posts: 4,043 Rep Power: 21	I know a guy $1850 plus a refundable $1000 core charge. __________________ 1976 Mazda Cosmo RX-5 1976 Mazda Cosmo RX-5 2003 Toyota Tundra TRD 2015 Toyota 4Runner SR5

03-31-2010, 07:43 AM	#13
FerociousP I-had-a-bad-experience... Join Date: Feb 2008 Location: M'boro iTrader: (2) Posts: 1,046 Rep Power: 18	its more like... he "knows" a guy 8===@ __________________ '15 Juke Nismo '06 MX-5 GT SOLD '04 S Silver RX-8 GT Track Day Use SOLD '90 Black TII vert w/ Sprint RE stock port/turbo DD dyno (242.6whp@5500rpm @12psi 8psi@redline) and (250ftlbtq@4800rpm @13psi) SOLD '89 GTUs 6p TII SOLD, '87 sport SOLD, '79 SA stock SOLD '91 B2600i 4x4 w/ Rx-8 LSD SOLD

07-27-2011, 02:22 PM	#14
fc3sfreak415 Wankel Works Join Date: May 2011 Location: Boston, MA iTrader: (0) Posts: 35 Rep Power: 0	If your lookin for an engine give nation wide auto recycling a call. They have 2 engines for sale for $1700 they both are used and under 60k with one year warranty on them and no core charge NATIONWIDE AUTO RECYCLING 978-534-0477 EXT 305

07-28-2011, 07:59 AM	#15
reddozen Gold Wheels FTW Join Date: Mar 2008 iTrader: (0) Posts: 744 Rep Power: 17	I got my short block for $1000 Shipped. I'd much rater go that route and have it rebuilt by someone fairly reputable than to risk anything with a factory Mazda reman. As mentioned, their clearances / tolerances are pretty sloppy. Hand cut side seals FTW. __________________ My Cars: 1974 RX4 Coupe 1991 FC3S RX7 - Sold 2003 ZZW30 MR2 (Rotary swap after RX8) 2004 SE3P RX8 (20B Swap in the works)

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode