|
|||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
 |
|
|
Thread Tools | Display Modes |
|
|||||||
| RX-7 2nd Gen Specific (1986-92) RX-7 1986-92 Discussion including performance modifications and technical support sections. |
|
|
|
Thread Tools | Display Modes |
08-30-2014, 06:39 PM
|
#1 |
|
Rotary Masochist
Join Date: May 2008
Location: Floyds Knobs, IN
Posts: 494
Rep Power: 18  |
FC clutch slave thread size?
Can anyone check the thread size on the hydraulic fitting on an FC slave, please? TIA!
__________________
_______________________________________________ One stop Haltech, AEM, Syvecs shopping. Installation and tuning. http://www.lms-efi.com Free support. Drop us an email. chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI |
|
|
|
08-30-2014, 07:14 PM
|
#2 |
|
Rotary Fan in Training
Join Date: Oct 2008
Posts: 87
Rep Power: 18 |
Not M10X1 like a lot of the others??
|
|
|
|
|
08-31-2014, 11:52 AM
|
#3 |
|
Rotary Masochist
Join Date: May 2008
Location: Floyds Knobs, IN
Posts: 494
Rep Power: 18 |
Nope. It's larger.
__________________
_______________________________________________ One stop Haltech, AEM, Syvecs shopping. Installation and tuning. http://www.lms-efi.com Free support. Drop us an email. chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI |
|
|
|
|
08-31-2014, 03:45 PM
|
#4 | |
|
RCC Addict
Join Date: Mar 2008
Location: Honolulu, Hawaii USA
Posts: 1,813
Rep Power: 19 |
The fitting on the clutch slave cylinder to the clutch slave flex hose?
The one that uses a 17mm hex fitting to remove and install? BTW, this is for a TURBO model... I just eyeballed it, and it does look like a 10mm fine thread, or 10mm x 1.0. The 10mm I got using a ruler. I can confirm in a few hours, as I don't have my fastener measuring tools with me right now... -Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
Last edited by RETed; 09-01-2014 at 04:23 AM. |
|
|
|
|
|
08-31-2014, 06:00 PM
|
#5 |
|
Rotary Masochist
Join Date: May 2008
Location: Floyds Knobs, IN
Posts: 494
Rep Power: 18 |
Yes. Maybe it is 10mm. Thought it was larger. Turbo and NA use the same hose, so either one will give the proper measurement.
__________________
_______________________________________________ One stop Haltech, AEM, Syvecs shopping. Installation and tuning. http://www.lms-efi.com Free support. Drop us an email. chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI |
|
|
|
|
09-01-2014, 04:23 AM
|
#6 | |
|
RCC Addict
Join Date: Mar 2008
Location: Honolulu, Hawaii USA
Posts: 1,813
Rep Power: 19 |
Confirmed.
10mm x 1.00 -Ted
__________________
reted_2000@yahoo.com Technical Advisor FC3S Pro http://fc3spro.com/ Quote:
|
|
|
|
|
|
09-01-2014, 07:04 AM
|
#7 |
|
Rotary Masochist
Join Date: May 2008
Location: Floyds Knobs, IN
Posts: 494
Rep Power: 18 |
Thanks Dannobre and Ted!
__________________
_______________________________________________ One stop Haltech, AEM, Syvecs shopping. Installation and tuning. http://www.lms-efi.com Free support. Drop us an email. chris@lms-efi.com 502-515-7482 Facebook @LMS-EFI |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
